Ecotech Marine MP40w ES VorTech, VorTech MP60w Setup Manual

070113

®

Setup Guide

Customer Support ...................... 1

Inside the Box ............................ 2

Maintenance ............................... 3

Installing the VorTech™ .............. 4

The EcoSmart Driver .................. 8

Mounting the Driver .................... 9

Operational Modes ..................... 10

Tidal Swell Mode ........................ 12

Nutrient Transport Mode ............ 13

1

Congratulations on your

purchase of a VorTech

™

MP40w ES

Propeller Pump!

Please read this entire setup guide before using your pump. By purchasing,

installing or using this product, you are acknowledging that the Limited

Warranty on p. 19 is part of the sale terms.

Short Pulse Mode ....................... 14

Long Pulse Mode ....................... 15

Reef Crest Random Mode .......... 16

Additional Modes ....................... 16

Lagoonal Random Mode ............ 17

Troubleshooting .......................... 18

Limited Warranty ........................ 19

Regulatory Information ............... 20

Customer Support

Many of the steps in this guide have corresponding how-to videos. View them
on the EcoTech Marine website at ecotechmarine.com/media-gallery/video.

®

The EcoTech Marine Community is another tool for users to troubleshoot and

learn about our products. For additional information about your VorTech
Propeller Pump, please visit us at community.ecotechmarine.com.

UNITED STATES & CANADA

Contact EcoTech Marine directly for all warranty service and returns.
Visit ecotechmarine.com/support

INTERNATIONAL

Contact your local distributor directly for all warranty service and returns.
Visit ecotechmarine.com/find-retailers/international-distributors

Customer Support

1-800-785-0338

[e-mail] or

ecotechmarine.com/support

2 3

Inside the Box

POWER SUPPLY POWER CORD FOAM GUARD

MOUNTING TABS (X4)

DRIVER

VELCRO STRIPS (X2)

DRY SIDE

ZIP TIES (X4)

WET SIDE

Your VorTech Propeller Pump is designed to operate optimally with little
attention after initial setup; however, due to the harsh conditions of a
saltwater aquarium and resulting buildup of algae and other organic
matter, it is advisable to clean your wet side to ensure the longevity
of your purchase.

EcoTech recommends doing a wet side cleaning every 6 to 8 weeks or
as necessary.

This can be accomplished by disassembling the pump's wet side and
gently brushing with a soft brush under running water. If there is calcium
buildup, it may be necessary to soak these parts
in a mild acid solution such as vinegar. Do not
use strong acids, because these may damage
the components.

After cleaning, reassemble the wet side, finger
tightening the drive shaft screw and nut. Do not
use tools to tighten components.

WET SIDE

DISASSEMBLY

WATCH THE VIDEO:

ecote.ch/mp40disassemble

Maintenance

Installing the VorTech

™

STEP 1: Choose Pump Location

• Where the pump output is unobstructed

• High enough above the sand bed so sand is not disturbed

• Sufficiently below the surface so air is not sucked into a vortex

STEP 2: Prepare Aquarium

• Use an aquarium scraper to clean the inside surface of the

aquarium and a damp cloth to clean the outside.

• Use caution when handling an aquarium scraper.

STEP 3: Attach Mounting Tab

•

Peel backing from the adhesive and place the tab 2-3" above
the desired mounting location on the outside of the aquarium
(Figure A).

STEP 4: Correctly Set Pin Spacer

•

Determine the glass thickness by measuring it (or contact
the aquarium manufacturer).

• Remove the rubber spacer from the bottom of the

motor housing (Figure B).

• Align the power cord according to the thickness marked

on the pin spacer. To do this, pull the pin spacer from
the motor housing, align the thickness mark and
carefully slide the pin spacer onto the motor (Figure C).

3/4" (19mm) thick aquariums DO NOT use the pin spacer.

STEP 5: Place Dry Side on Aquarium

•

Place the rubber spacer directly on the wall of the
aquarium at the desired location (Figure D).

• Position the dry side so the cord points straight up in the

12 o’clock position (Figure E).

• Tie the cord to the mounting tab using a zip tie (Figure E).

Trim the excess end of the zip tie.

Never place the dry side in the aquarium.

When adjusting the pin spacer, be careful not

to bend the rubber pins when inserting them into

the holes within the motor housing.

4 5

Figure A

Figure B

Figure E

Figure C

Figure D

SETUP YOUR

MP40

WATCH THE VIDEO:
ecote.ch/mp40setup