Ecostrad GH-20F-APP Instruction Manual

Ecostrad iQ Glass Electric Panel Heater

– 2000w with WiFi Control

Instruction Manual

GH-20F-APP

Please read the manual carefully prior to use

Safety Instructions

• Read the manual before you use the heater. Keep the manual and ensure it
stays with the heater if you give it to a new owner.

• Before use, check that the heater and all supplied accessories are complete and
intact.

• The heater must be installed as per installation instructions. The heater must be
plugged into a socket that meets the following requirements: AC 230V,

frequency 50/60Hz.

• The heater is only suitable for indoor use. Do not use it outdoors!

• Do not leave the heater unattended during use. Keep the heater out of the reach

of children: risk of burns.

• Do not use an external controller with the heater. The heater must not be set to
switch on when it will be unattended.

• Do not use the heater near flammable or explosive materials: risk of fire or
explosion.

• Inserting items into the protective grill of the heater is strictly prohibited: risk of
electric shock.

• Do not touch the metal housing as it will get hot when the heater is in use: risk of
burns. Set aside some time to let the heater cool before you turn it off and store
it.

• Unplug the heater if it is going to be out of use for a long time.

• Prior to each use of the electric heater, make sure it is in a good condition and

intact. Do not plug in or use the heater if the casing, wire or plug are damaged.

• The heating element may be damaged if the heater is dropped or hit. Check that
the element is not damaged prior to each use. Do not use the heater if the
element is broken.

• Disconnect the plug from the socket when moving or cleaning the heater. When
disconnecting, first turn off the switch, then unplug the plug. Do not yank the
cable.

• Demolition of the electric heater without authorization is strictly prohibited.
Please look for professional service personnel if the heater is damaged.

• The product is limited to home use only.

• During use, do not let bare skin touch the surface of the appliance: risk of burns.

• Do not share the heater’s socket with other appliances: risk of fire due to

excessive load.

• CAUTION: never cover the heater. Covering the heater risks overheating and
fire.

• The heater must not be located immediately below an electrical socket-outlet.

• If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or a similarly qualified person to avoid a hazard.

• Avoid the use of an extension cord as this may overheat and cause a fire risk.

• This heater is not intended for use in bathrooms, laundry areas or similar

locations where there may be moisture. Never place the heater where it may fall

into a bathtub or other water receptacle

• Do not use the heater in the immediate surroundings of a bath, shower or
swimming pool.

• Children of less than 3 years should be kept away unless continuously
supervised.

• Children aged from 3 years to 8 years shall only switch on/off the appliance
provided that it has been placed or installed in its intended normal operating
position and they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children aged
between 3 and 8 years shall not plug in, regulate or clean the appliance or
perform maintenance.

• This appliance can be used by children aged 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.

• CAUTION: some parts of this product can become very hot and cause burns.
Particular attention must be given where children and vulnerable people are
present.

Installation Instructions

• Before installing, check that all parts are complete and the product is intact.

• If you want to use the electric heater freestanding, please fit with the feet

provided with the heater, following the instructions below. Make sure the heater
is mounted on a level, stable and clean surface.

Freestanding Installation

1. Put the product upside down on a

soft cotton cloth or carpet.

2. Fix the feet to the base of the

heater using the screws provided.
Line up the holes in the base with
the holes in feet, put the screws
through the holes and tighten with
a screwdriver.

Wall Mounted Installation

Hook

Hook

Expansion Screw
Expansion Screw

Wall Bracket

Lock Piece

1. Take out the wall brackets and expansion screws from the box. Fix the screws

onto the wall according to the distances between the holes of the wall brackets,
as depicted below:

2. Slot the hooks and tongues of the brackets into the corresponding notches at the

back of the heater. Pull the brackets up until they slot into place, as shown below.

3. On the top of the right bracket, fix the wall bracket lock piece as pictured. Fix the

lock piece loosely onto the bracket with the supplied screw. Slide the lock piece
into the locking slot on the back of the heater, then tighten up the screw.