ECO Spot LED40DE User Manual

ECO Spot LED40DE User Manual



ECO Spot™ LED40DE User Manual

that complies with local building and electrical codes and

defective or wet, or if they show signs of overheating.

The ECO Spot LED40DE is intended for exterior applications but
is also suitable for interior use. Thank you for choosing an ECO

Spot™ Gobo projector. This unit is equipped with a fan cooled heat
pipe to keep the 40W High Power LED running cool. It is also
available as interior version (ES-LED40D).

Please read this manual before installing or operating this fixture,
follow the safety precautions listed below and observe all warnings.

WARNING!
To prevent damage to the LED, always connect the driver
cable to the projector FIRST before plugging it into the
power outlet.

Package Contents

Projector, External LED Driver, Test Gobo, Spare gobo retaining ring and spare drive

belt, Gobo adapter ring for E-Size Gobos

Safety Information

• Place your fixture at a suitable place with good air flow.

• Keep flammable materials away from the fixture.

• Minimum distance to flammable material = 1 ft (0.3m).

• Minimum distance to illuminated surface = 3.3 ft (1.0m).

• Provide a minimum clearance of 4 in (10cm) around air vents.

• Use only genuine spare parts for part replacement.

• Do not look directly into the lamp; it can cause eye damage.

• Always unplug the unit from the power mains before any service is done.

• Light fixtures should be installed and maintained only by qualified personnel with

experience in lighting equipment and general electrical experience.

• Disconnect the fixture from AC power before handling the fixture.

• Always ground (earth) the fixture electrically.

• Use only a power source

has both, overload and ground-fault protection.

• Do not use the fixture if the power cable or power plug is in any way damaged,

Copyright © 2014 Globus New Media LLC Page 1

ECO Spot LED40DE User Manual

can hold

an approved means of secondary attachment such as a safety cable.

the image is well focused.

When used for the first time, the lens will often need to be twisted outwards many

• Re-tighten the outer ring to ensure a tight seal of the lens.

Handling Instructions

• There is a weatherproof connector between the driver (power supply) and

projector, which can be opened for easier handling. Always make this
connection first before powering up the driver, otherwise the LED can be
damaged by the power surge.

• Before the initial start-up, please unpack and carefully check for damage caused

during transportation.

• Place your fixture at a suitable place with good air flow.

• Make sure there are no flammable materials close to the lamp.

• When suspending the fixture above ground level, verify that the structure

at least 10 times the weight of all installed devices.

• Verify that all external covers and rigging hardware are securely fastened and use

Warranty

One Year from Date of Purchase. Keep your receipt for reference and contact your dealer
in case of warranty issues.

Projection Lenses

The projector accommodates interchangeable projection lenses to allow optimizing the
projection size and resulting brightness at varying distances. The more narrow the lens,
the smaller and brighter the image will be at a given distance. For example, cutting the
projection size in half, will quadruple its brightness.

Gobo Rotator

If the fixture is equipped with a gobo rotator, it can be turned on/off with the silver push­button on the front plate underneath the lens. There are no controls for rotating speed or
direction.

Focusing

• Power up the projector.

• If the fixture is equipped with a gobo rotator, turn it on, once the gobo projects in

the desired position, turn it off.

• Loosen the outer ring around the lens that acts as a water seal.

• Focus the projection by twisting the lens in and out until

rotations to reach the focusing point. When in doubt, keep going.

Page 2 Copyright © 2014 Globus New Media LLC

ECO Spot LED40DE User Manual

• The yoke can be screwed to a wall or ceiling or fastened with a C-clamp

the projection lens in or

out.

Multi-functional Yoke

• The yoke can slide over the whole length of the fixture body to accommodate a

wide range of pointing directions.

• The yoke can also serve as stand.

Gobo Placement (see Specifications for Gobo Dimensions)

The ES-LED40DE uses D-Size gobos or E-Size gobos with an adapter ring. See the
Specifications for exact dimensions. For max. image size and brightness use D-Size gobos.
The recommended gobo image diameter is 35mm. An Image Diameter of up to 40mm is
possible with some loss in focusing quality for optimal focus, stay within 32mm image
size.

• Unscrew the thumbscrews to remove the front cover with the projection lens.

• Push the two pins of the gobo retaining ring together and pull out the retaining

ring. Carefully remove the old gobo and replace it with the new gobo.

• Tip: Tilt the projector forward while placing the palm of your hand inside, the old

gobo will fall into your hand.

• If you have a glass gobo, place the more reflective side towards the light bulb.

• Replace the retaining ring and make sure it evenly pushes the gobo all the way

back.

• Replace the front cover and adjust the focus by threading

Copyright © 2014 Globus New Media LLC Page 3

ECO Spot LED40DE User Manual

• Effective luminous flux: 1,500lm

• Narrow 10º (eff. 14º)

• Fixture: equivalent to IP62

Line Voltage

100-240V, 50/60Hz, 0.6A, 48W

Ambient Operating Temperature

-13 to 104°F (-25 to 40°C)

Dimensions / Weight

Body without yoke:

10.5 x 6 x 3.75in (L x W x H)

(267 x 153 x 95mm)

The projection lens adds 0.5 to 2in (12 to

50mm) to the length.

Height with yoke: 7.75in (197mm)

Weight 7lbs (3kg)

Gobo Dimensions D-Size

Metal or Glass Gobos and Dichroic filters

The projector takes D-Size gobos:

Outer Diameter (OD): 53mm

Image Diameter (ID): 35mm

Max Thickness: 4mm

Larger ID up to 40mm is possible with
some loss in focusing quality, for optimal
focus stay within 32mm image size. An
adapter for the smaller E-Size gobos is
included.

(max 40mm)

LED Lamp

• Extremely high light density for

ultra-efficient projection.

• Power: 40W

• Bulb life 50,000h

• Color Temperature 5,500k, +/-

500k

• Rated Luminous flux: 2,000lm

Lens Options

The projector can be equipped with
standard projection lenses of the ECO
Spot line. These lenses are marked based
on a gobo image size of 25mm. With the
larger gobo image size, a given lens
produces a larger image than the lens
specification, see the effective lens angles
in () below. The more narrow the lens, the
smaller and brighter the image will be at
a given distance. Currently these lenses
are available:

• Wide 25º (effective 35º)

• Medium 20º (eff. 28º)

• Medium Narrow 15º (eff. 21º)

IP Ratings

• LED Driver: IP65

Page 4 Copyright © 2014 Globus New Media LLC