Outdoor Digital Timer
OPERATING INSTRUCTIONS
2. Reset
There is a reset hole under the dashboard.
Insert a pin or paperclip into the hole to reset
the timer. This will clear all programmed
settings.
Before initial use, plug the timer in for at least 30 minutes to charge the
internal battery. After the screen displays, the unit is ready for
programming.
The device must be mounted in a vertical position with the receptacle
facing downward and with the receptacle at least 2 ft above the
ground level.
1. Button Layout
1. MODE - Manual override and scroll
between the timer status options.
2. TIME - Press and hold for two seconds to
set current time.
3. PROG - Press and hold for two seconds to
begin setting function.
4. < + > - To increase time and day setting.
5. SET/ - Setting confirm and clear setting.
6. < - > - To reduce time and day setting.
7. RESET - Reset all the functions.
8. PHOTO SENSOR - The sensor will sense for light and dark, and
direct the timer to act accordingly.
3. Set Current Time
a. Press and hold "TIME" button for 2 seconds
to enter the current time settings. Press "+"
or "-" button to set the correct day.
b. Press the "SET" button to enter the hour
setting. Press "+" or "-" buttons to set the
current hour. Be sure that AM or PM appears
correctly.
c. Press the "SET" button to enter the minute
setting. Press the "+" or "-" buttons to set the
current minute.
d. Press the "SET" button to finish setting the current time and return to
normal display.
e. While setting those processes above, press and hold “SET” button
can clear the setting and back to the original timer settings. While
setting those processes above, press “TIME” button or wait for
15 seconds to back the standby display.
3
2
MODE TIME
PROG
+
-
SET/
1 2 3
4
6
8
8
5
1
4. MODE Setting
Press “MODE” button to choose the desired
mode.
ON→OFF→RDM Timer→AUTO Timer→
AUTO CDS→AUTO CDS + TIMER as
following listed.
The below icons will appear on the right of
display.
4
4-1
1. ON - Always on
The outputs remain always on.
4-2
2. OFF - Always off
The outputs remain always off.
4-3
3. RDM - Security feature.
On at a random time, and remains ON for
15 minutes.
Up to 5 on/off events every day.
The on/off events are built into this
product, turn ON at a random time and
the ON time is different each day,
creating a more “lived-in” look.
4-4
4. AUTO - ON/OFF program at AUTO mode.
ON/OFF at your exact programmed time.
4-5
5. AUTO - Photocell
ON at dusk, OFF at dawn.
4-6
6. AUTO - Program and Photocell
On at dusk, OFF at your exact
programmed time.
5. Program Setting
Make sure the current mode is at AUTO
mode, then press and hold "PROG" button for
two seconds to begin program setting, using
the "+" and "-" buttons to adjust the setting.
1. Press the "+" or "-" button to set the
correct day.
MO, TU, WE, TH, FR, SA, SU, MO TU WE TH FR, SA SU, MO TU
WE TH FR SA SU (cycle).
2. Press the "SET" button to enter the hour setting. Press "+" or "-"
buttons to set the desired hours for your timer to turn on. Be sure
that AM or PM appears correctly.
3. Press the "SET" button to enter the minute setting. Press the "+" or
"-" buttons to set the desired minutes for your timer to turn on.
4. Press “SET” button to enter the program OFF setting, the “1 OFF”
will appear on the display. Repeat steps 1 to 3 to set your desired
OFF time, up to 8 on/off programs settings.
5. While setting the programs, press and hold the “SET” button to
clear the set program time.
6. Once you complete the programs settings, press the “TIME” button
or wait for 15 seconds to restore your programs to back the
standby display.
5
6. Photocell Setting
Press the “MODE” button to select the
photocell function. This setting will
automatically turn the power on at dusk and
turn the power off at dawn.
6
7. Program and Photocell Setting
1. Press “MODE” to select “AUTO Program and photocell setting”,
then press and hold the “PROG” button for two seconds to set the
off time.
TM-108 Size: 145x210mm
Front
MADE IN CHINA
2. Press the “+” or “-” button to set the
desired OFF day of the week program.
You can select each day individually,
Monday to Friday, Saturday/Sunday, or
an entire week to have your timer turn
on at dusk and off at the set time.
3. Press the “SET” button to enter the
OFF time hour setting. Press the "+" or
"-" buttons to set time. Be sure to cycle
through until AM or PM appears correctly.
4. Press the “SET” button to enter the OFF time minutes setting.
Press the "+" or "-" buttons to set time.
5. You can press the “SET” button to enter additional programs, up to
8 off program settings. While setting the programs, press and hold
the “SET” button to clear the set program time. Press the “TIME”
button or wait for 15 seconds to store the program, and return back
to the standby display.
7-1
HELPFUL TIPS
SAFETY INFORMATION
Do not attach a device that exceeds the unit ratings as described in the
Safety Information section of this manual.
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
SPECIFICATIONS:
14/3 AWG SJTW vinyl cord
RATINGS:
125 V ac 60 Hz, 15 A Resistive,
15 A General Use, 1000 W Tungsten,
500 VA Electronic Ballast, 1/2HP.
120 V ac 60 Hz, 8.3 A Ballast.
SUITABLE FOR USE WITH OUTDOOR APPLIANCES – RAINTIGHT
WHEN MOUNTED VERTICALLY WITH THE RECEPTACLE FACING
DOWNWARD. NOT FOR WATER IMMERSION.
This equipment has been tested and found to comply with the limits for
Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation of the device.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
WARNING
CARE AND MAINTENANCE
• Store indoors in dry location.
• Always unplug when not in use.
• Do not unplug by pulling on cord.
TROUBLESHOOTING
PROBLEM POSSIBLE
CAUSE
CORRECTIVE
ACTION
Lights do not
turn on at dusk.
Timer is not in a good
area for light meter to
function as there is too
much ambient light to
detect darkness.
Move the timer to another
location where there is no
ambient light.
Lights do not
turn on, even
when timer is in
“ON” position.
Lights are not in “ON”
position, lights are not
functioning, or timer is
not receiving power.
Be sure that lights are
functional by plugging
them directly into the
outlet. Be sure that lights
are in “ON” position if they
have their own switch. Be
sure that timer is receiving
power - the LED should
light up when plugged
into an outlet and put in
the “ON” position.
Lights are
flashing (turning
on and off).
The timer is in Dusk to
Dawn mode, and the
light from the
plugged-in lights is
affecting the light
sensor.
Move the lights away from
the timer, or reposition the
timer so that it does not
face the lights.
Back
Loading...