Ecolink Intelligent Technology SCZ5 User Manual

SIREN+CHIME (Z-WAVE PLUSTM)

PRODUCT OVERVIEW

The Ecolink Siren+Chime is a Z-Wave PlusTM enabled device intended to integrate into a Z-Wave PlusTM home
automation network for the purpose of sounding a siren or chime when told to do so by a controlling device. It can
be used to sound its siren when a house has been broken into; to chime when a monitored door or window is
opened; and to give audible user feedback on the state of the security system with entry-delay and exit-delay
tones.

 Plug and Play for Z-Wave Plus enabled Alarm Systems
 Chime (Programmable) to alert when zones are opened
 120 dB Siren
 Can be plugged into any AC outlet and screwed into faceplate for solid installation

PRODUCT SPECIFICATIONS

 For indoor use only
 Operating Frequency 908.42 MHz
 Operating range: Up to 100 feet (30.5 meters) line of sight
 Operating temperature: 0˚C to 49˚C, 32˚F to 120˚F (ambient temperature)

HOW DO I USE THIS?

The Siren+Chime can be enabled through “scenes” to make noise under certain conditions defined in your scene.
A scene on some gateways can be called an “automation,” or a “Smart App.”

However, not every Z-Wave PlusTM controller allows our devices to appear for the user to properly use and control
via their user interface. You should check with the manufacturer of your particular Z-Wave PlusTM controller to see
if they support our device explicitly. If they do not explicitly support our device, it may still work with limited
functionality. In fully supported controllers, the Siren+Chime device would show up as such, and all or most
functionality will be enabled within the user interface, otherwise this device may appear as a generic electric
outlet and be controlled as if it were a lamp. An incomplete list of compatible Z-Wave PlusTM gateways may be
found on our website at www.discoverecolink.com.

If your Z-Wave PlusTM controller only allows the Siren+Chime to be controlled as if it was single electric outlet,
you can choose whether your Siren+Chime is just a siren or just a chime via the jumper labeled “J5” on the back of
the device. With the jumper placed, the device will enable its chime functionality, and with the jumper removed
(default) the siren functionality is enabled.

© 2016 Ecolink Intelligent Technology Inc. PN SC-ZWAVE5-ECO R1.01

Endpoint

Sound

1

Default

Siren

J5 Jumper Placed

Chime

2

Default

Chime

J5 Jumper Placed

Siren

3

Entry Delay

4

Exit Delay

If the Siren+Chime is semi supported via its multiple endpoints, the Siren+Chime may appear on the user interface
as a collection of switches or power outlets.

WHAT IS Z-WAVE PLUSTM?

The Z-Wave PlusTM protocol is an interoperable, wireless, RF-based communications technology designed
specifically for control, monitoring and status reading applications in residential and light commercial
environments. It is a mesh network that can allow non-sleeping devices to extend the range of an existing
network. The Z-Wave Plus protocol is a standard governed by the Z-Wave PlusTM alliance, and allows for most
certified Z-Wave PlusTM devices to communicate and interoperate with each other.

For a more complete look at Z-Wave technology for non-technologists, and to learn more about Z-Wave's role as
a key enabling technology for the Internet of Things and connected objects, please visit www.z-wave.com.

HOW CAN I ADD IT TO MY EXIS TING NETWO RK?

1. As stated above, be sure that our device is enabled to work with your Z-Wave Plus

2. Plug the Siren+Chime into the wall and observe the LED’s behavior. If after 10 seconds, the LED fades from

on to off continuously, this means that the Siren+Chime is ready to be added to your Z-Wave PlusTM
network. If LED turns off, that means that the Siren+Chime is already learned into an old Z-Wave PlusTM
network and must be excluded first.

To do this, follow the directions below on removing a Z-Wave PlusTM device or factory defaulting the device.

1. Unplug the Siren.

2. Follow your Z-Wave Plus

TM

controller’s instructions for activating its Add (Z-Wave PlusTM inclusion) mode.

3. Plug the siren in to power. On power-up, the Siren+Chime goes into learn mode. Wait 10 seconds for user

feedback that your Z-Wave PlusTM controller’s inclusion mode has completed.

TM

controller (hub).

HOW CAN I REM OVE IT FROM MY NETWORKOR AN OLD NE TWORK?

© 2016 Ecolink Intelligent Technology Inc. PN SC-ZWAVE5-ECO R1.01