Ecolink Intelligent Technology FLZB1ECO Users Manual

FLZB1-ECO

ENROLLING

To enroll the sensor, remove the top cover by prying off
at one of the tabs on either side. Set your panel into
program mode. Refer to your specific alarm panel
instruction manual for details on these menus. Once in
program mode, place the batteries into the sensor and
follow the instructions that appear on the panel. When

“Trip to Pair” appears on the screen, press the tamper

button to complete the enrollment process. See LED
section below for more information on initial power up
behavior.

NOTE: For best results, pair the device to your panel
before installation.

A Universal Electronics Company

Flood Sensor

Installation Manual & User Guide

SPECIFICATIONS

Frequency: 2.4GHz Operating Temperature: 32°-120°F (0°-49°C)
Battery: Two,1.5Vdc AAAA Alkaline (3Vdc Nominal) Operating Humidity: 5-95% RH non condensing
Battery life: 4 years? Supervisory signal interval: 27 min(approx.)
Water Detect Depth: Minimum of 0.397mm (1/64”) Maximum current draw: 135mA during transmission
3rd Party Certifications: FCC, IC, ETL, ZigBee 3.0

OPERATION

The FLZB1-ECO is a battery-powered sensor for home security or home automation applications. The FLZB1-ECO is
triggered by the presence of water in contact with the built in flood probes on the bottom of the case which
causes the FLZB1-ECO to transmit.

MOUNTING

The device is designed to be used on a flat surface without the need for mounting. A protective cover is supplied
which can be screwed down over the sensor to protect it from damage or from being moved from the set location.

LED

The Flood Sensor is equipped with an LED. On power up, the LED will stay solid for 2 seconds, then blink 3 times every
5 seconds (approx.) when not enrolled with a panel. If the sensor is already enrolled into a network, it will illuminate
the LED for approximately 4 seconds and then turn off.

REPLACING THE BATTERY

When the battery is low a signal will be sent to the control panel. To replace the battery:

1) Remove the Flood Sensor from installation location by removing protective cover if necessary.

2) Pry the cover open using the notched areas on either side.

3) Replace the two AAAA 1.5Vdc batteries ensuring the + side of the battery faces as indicated on the device.

4) Re-attach the cover, you should hear a solid snap when cover engages properly.

5) Replace the protective plate if necessary.

REBOOTING AND RESETTING TO FACTORY DEFAULTS

In order to reboot the device, simply remove the battery and place it back in. Upon doing this, you should see the LED
illuminate. See LED section for more information on LED behavior.

To reset the device to factory defaults use the following instructions:

1. Open case and remove battery from device.

2. Press and hold tamper switch.

3. Place battery back into the device while still holding the tamper switch.

4. When you see the LED illuminate, release the tamper switch.

5. After releasing the switch, the device will restore to factory defaults and the LED should begin blinking again.

PACKAGE CONTENTS

Included Items:
1 x FLZB1-ECO Flood Sensor
1 x Protective Plate
2 x Mounting Screws
2 x AAAA batteries
1 x Installation Manual

Non-Included Items:

Security Control panel

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment to an outlet on a different circuit from the receiver

• Consult the dealer or an experienced radio/TV contractor for help.

WARNING: Changes or modifications not expressly approved by Ecolink Intelligent Technology Inc could void the

user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.