Ecolink Intelligent Technology CS732 Users Manual

Problem

Solution

Attempt to pair the sensor is unsuccessful.

Please refer to control panel manuals for pairing.

The sensor and the control panel does not communicate.

Perform the signal strength testing procedure described in the control panel installation manual. Make sure that the signal is sufficient. If

necessary,

replace the sensor’s battery.

The sensor sends a Low Battery

indication.

ensure continuous proper operation, replace the battery within two weeks of the first Low Battery indication.

2055 Corte Del Nogal Carlsbad, California 92011 1-855-632-6546 www.discoverecolink.com

TROUBLESHOO

If you encounter one of the following problems with the CS-732, resolve

the problem:

TING

use the following solutions to

CS-732

ClearSky Occupancy Sensor 345 MHz

Installation Instructions

5. COMPLIANCE WITH STAND

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B 15 of the FCC Rules. These limits are designed to provide reasonable installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause will not occur in a particular installation. If this equipment does cause harmful interference to radio or television which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient

• Increase

• Connect the equipment into an outlet on a circuit dif

connected.

• Consult

Warning:

authority to operate the equipment.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil. In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element shall be installed such that a minimum separation distance of 20 cm is maintained from the general population. Conformément aux exigences d'Industrie Canada en matière d'exposition humaine aux champs de radiofréquences, l'élément rayonnant doit être installé de telle sorte qu'une distance minimale de 20 cm soit maintenue par rapport à la population générale.

FCC ID: XQC-CS732 ICID: 9863B-CS732

relocate

the

separation between

the

dealer

Changes or modifications not expressly approved by the Ecolink Intelligent Technology Inc.

harmful

the

or an

interference to radio communications. However, there is no guarantee that interference

receiving

experienced radio/TV technician

antenna.

the

equipment

ARDS

protection

and receiver.

ferent from that to which the receiver is

for help.

against harmful interference in a residential

digital

device, pursuant to Part

reception,

could void the user’s

1. INTRODUCTION

The CS-732 wireless digital PIR occupancy sensor supported by ClearSky 345 MHz.

Detector Type: Two - Dual element low-noise pyroelectric sensor Optical Data:

Max. Coverage: 15 x 15 m, (49.2 x 49.2 ft)

ELECTRICAL

Internal Nominal Battery Battery Life: 5 years

FUNCTIONAL

Occupancy

Visual

WIRELESS

Supported Frequency: 345 MHz Tamper

MOUNTING

Height: Installation

ENVIRONMENTAL

Operating Temperatures -10˚ C to 55˚ C (14˚ F to 131˚ F) Storage Temperatures -20˚ C to 65˚ C ( -4˚ F to 149˚ F)

PHY

Size (H x W x D) 83 x 61 x 42 mm (3.27 x 2.4 x Weight (with battery) 90 g (3.17 oz) Color White

is a microprocessor-controlled

SPECIFICA

Batteries:

Capacity:

Transmission:

Indications:

Network:

Alert:

Options:

SICAL

TIONS

parabolic mirrors for long range

parabolic mirrors for close range

Two 3V Lithium batteries, type CR-123A. 1400 mAh per battery

Once the occupancy sensor is in normal operating mode (after exiting the 15 minute walk test mode) the occupancy sensor will send an occupied transmission to the control panel upon motion detection. The sensor will not re-send occupied transmission signal until after approximately 3 continuous minutes without motion has been observed by the sensor. After approximately continuous 3 minutes without motion, the sensor will send an unoccupied transmission signal to the control panel and resume normal occupancy detection.

Upon installing the batteries or removing the pull tab, the red LED during

the power-up stabilization period. mode. During the 15 minute walk test mode, the red LED lights for about 3 seconds upon prior to transmission of the occupancy signal. The LED does not light upon transmissions or detection the 15 minute walk test mode has ended.

ClearSky

Reported when a tamper event occurs and in

1.8-2.4 m (6 - 8 ft). Surface or corner

/ 90°

will flash for approximately 1 to 2 minutes

The sensor will then automatically enter the 15 minute walk test

any subsequent message, until the tamper switch is restored

1.66”)

motion d

etection

after

Note: Rebooting the detector will put it in walk test mode for 15 minutes.

INST

3.1 General Guidance

1. Do not install near heating and cooling sources.

2. Do not aim detector at windows due to risk of drafts.

3. Do not install outdoors.

4. Do not install where direct sunlight can strike the

5. Do not install near high-voltage electrical lines.

6. Do not install behind any obstructions.

7. Do not mount on unstable surfaces.

ALLA

TION

unit.

3.2 Installation Procedure

Separate detector from bracket. Figure 3.

Remove the bracket.

Mount bracket to wall using the center screw holes (B) or corner screw holes (A1 & A2). Figure 4.

Install new batteries OR if batteries are installed, remove the activation strip.

Remount the detector by sliding it down onto the bracket until a click is heard. Figure 5.

The unit is ready for walk test.

3.3 Replacing the Batteries

1. Press upward to separate the detector the bracket.

2. Replace the ba

3. Put back the detector on the bracket.

Note: It is recommended to wait approximately 1 minute after battery removal before inserting the new battery.

CAUTION! Risk of explosion if battery is replace by an incorrect type. Dispose of used battery according to the manufacturer’s instructions.

tteries.

from

Figure 2. General

Guidelines

3.4 Activating and Pairing the

pair the detector to the control panel, you must set the panel to pairing mode.

1. First set the control panel to pairing mode.

2. To activate, pull the activation strip that protrudes from the back of the detector or insert the batteries.

3. If required, manually enter in the serial number of the sensor to the control panel.

Verify from the control panel that the sensor has been paired.

Note: Pairing should be performed before

Detector

installation.

Note: Serial number is the 6 digits located in the battery compartment underneath the QR code.

3.5 Rebooting the

reboot the detector, complete the following steps:

1. Remove the battery cover

2. Remove the batteries for 3 seconds and reinstall them

3. Close the battery cover

Detector

3.6

Unpair

1. Follow control panel instructions to remove the sensor from the network.

3.7 W

alk T

While the occupancy sensor is in the 15 minute walk test mode, walk across the far end of coverage pattern in both directions. The LED should light for 2-3

Important! Instruct the user to walk test at

least once a week to verify proper function of the detector.

Note:

After battery insertion or closing the cover (which results in closing the tamper switch)the LED the detector goes into walk-test mode for 15 minutes. In walk test mode for every motion detected. After 15 minutes the detector automatically enters normal in which the LED detection.

the Detector

esting

flashes for 1 to 2 minutes and

will not blink after

from Panel

the LED

lights

mode

seconds

each time your motion is detected.

Figure 7 – Coverage Pattern Walk-Test

Ecolink Intelligent Technology CS732 Users Manual

Specifications and Main Features

Frequently Asked Questions

User Manual