Ecolink Intelligent Technology BHAPIR001 Users Manual

Motion Detector
Home security beyond the front door
Ring Video Doorbells began a Ring of Security around your entire property.
Ring Protect is the security system that takes the Ring of Security a step further giving you another level of protection for your property.
Contents
1. Diagram
2. In-app Setup
3. Connecting the Device
4. Physical Installation
1. Say hello to
your Ring Motion Detector.
Diagram
Detector
LED Ring
Mounting bracket
2. Set up your
Ring Motion Detector in the Ring app.
Set up your Ring Motion Detector near your Base Station
In the Ring app, choose Set Up a Device.
Choose Sensors, then Ring Motion Detector.
3. Connect your
Ring Motion Detector to your base station.
Scan the QR Code or enter the S2 PIN
The QR Code and PIN can be found on the back of your device, on the box, or on the card in this box.
27472
5. Troubleshooting
Ring_Motion_Detector_Manual.indd 9 9/4/17 8:43 PM
Pull the tab on the detector
RING, ALWAYS HOME, and CHIME are trademarks of Ring Inc.
Last updated: 09/04/17
This connects the battery and turns on the device. Your base station will find it.
12345
Track the connection progress of the sensor
Your sensor will try to connect to your base station. The sensor’s LED ring will show you the progress.
Waiting to connect
Blue Blinking (30 sec)
4. Install your
Ring Motion Detector on
Place your detector (but don’t install it yet)
Hold the detector where you want to install it. Make sure the detector detects motion in the whole area.
Install your detector.
Use the bracket and tape or screws included in your kit. The detector can be mounted flush to the wall or angled in a corner.
View detector history in the Ring app
You should have a few history events from installing your detector. Check your app to make sure it’s working.
5. Some
additional details about
How to change the battery
Your battery should last quite a long time, but when you need to replace it, press the clip and remove the detector cover.
Connected
Couldn’t add to base station
Motion detected
Sensor tampered
Ring_Motion_Detector_Manual.indd 18 9/4/17 8:43 PM
Blue Solid (5 sec)
Blue Blink (5x, quick)
Blue Blink (1x)
Blue Blinks (3x)
the wall.
your detector.
© 2017 Ring Inc.
1523 26th St. Santa Monica, CA 90404
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
CAN ICES-3 (B)/NMB-3(B) – This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The FCC ID of the device in this package can be found on the back or bottom of the device.
CAUTION
To reduce the risk of electrical shock, DO NOT open the unit. There are no user serviceable parts inside the unit. Refer to customer support for any repairs.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same of equivalent type recommended by the manufacturer. Dispose of the used batteries according to the manufacturer’s instructions.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Ring_Motion_Detector_legal.indd 1 9/11/17 6:55 PM
Ring_Motion_Detector_legal.indd 2 9/11/17 6:55 PM
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Protect the device from direct sunlight. Install the device at dry locations, and protect it against rain and humidity. The device may not get in contact to salt water or other conductive liquids. The device must be charged only within a building in a dry state.
This device may not be disassembled and used for any other purpose. This unit, and all the components are configured for the sole purpose of providing a security. They are not approved for individual cellular use, battery use or other mishandling.
A
mobile app must be used to set up the device.
This device is not an Access point or Hotspot and should not be used as one.
Loading...