Ecoboil EC 30 Installation And Maintenance Instructions Manual

Water boilers | Water chillers | Boil/Hot units | Boil/Hot/Chill units | Parts & Accessories

EC 30 Arctic Chiller

Automatic Under Bench Water Chillers

Installation and maintenance instructions

Please read prior to installation

Important

This unit must be installed by an authorised plumber

The unit to be connected in accordance with AS 3500.4.1

or AS/NZS 3500.4.2

Do not turn on power to this chiller until water is flowing

from the tap

Please leave these instructions with the owner

WHAT’S IN THE BOX:

1 x EC 30 Chiller Unit
1 x UBFKI 10C Filter Kit
(kit includes EC 02 Chiller/Filter Tap and EB FMP 350 kPa PLV)

Prior to installation

• This unit is intended to be installed underneath a conventional
kitchen sink. However as a refrigeration unit it relies upon air
exchange to function properly, ensure adequate ventilation is
provided.

• When fitting this unit in a cupboard leave 25mm in the front and
back of the unit and 50mm either side of the unit.

• Only Teflon tape to be used where necessary. Under no
circumstances is plumbing paste to be used.

Product Information

• The 350 kPa Pressure Limiting Valve supplied must be fitted.

• Do not tip chiller unit on its side or end, if this has happened

reposition and wait 30 minutes for the oils to return.

• We recommend changing the filter cartridge every 12 months.

• The condenser should be periodically cleaned with a brush air

hose or vacuum cleaner. Disconnect the power supply during
cleaning.

• If the supplied power cord is damaged, it must be replaced by an
electrician.

• Temperature control is adjustable, with a cooling capacity of 2-12
degrees Celsius.

Installation Instructions

1. Do not plug in the unit or turn on the power until the installation

process is complete.

2. Position the unit underneath the sink so that the chiller air-intake

is as close as possible to the front of the cupboard. The cupboard
floor which extends past the toe-board must have a slot cut into it
to provide the necessary ventilation (preferably at least 20mm
wide by 3/4 the width of the cupboard door).

3. Ensure the connecting lines are thoroughly flushed to remove all

foreign matter before connection to the chiller.

4. Position the tap in the desired location. Drill an 11mm hole to fit.

5. Secure the 10” Water Filter, with the bracket and screws

provided, to the cupboard wall in a handy position relative to the

Main water line as shown in the diagram, taking careful note of
the flow direction.

6. Use the quick fit ends to connect the blue 1/4” line

7. Now connect the hose to the Filter Tap to the units as follows:

a. Connect the 1/4” pipe from the tap to the chiller outlet port.
b. Connect the 1/4” pipe from the filter outlet to the chiller inlet.
c. Connect the 1/4” pipe from the filter inlet to the 350 kPa PLV.
d. Connect to the mains water supply using Plumber’s Mate
fitting provided.

8. Open tap until water is flowing from the spout. Once the water

is flowing freely out of the tap plug in the unit to a standard 3 Pin
10 Amp Power Socket and switch on the power. Allow 20 minutes
for the initial chill cycle before using.

9. Check for leaks at all connections.

Trouble Shooting

SYMPTOM CAUSES ACTION

Water not cold No power supply

Thermostat

Loss of gas

Failed fan

Check and test power supply

Not set correctly

Contact Supplier

Contact Supplier

Slow water flow Old water filter

Blocked PLV

Replace filter cartridge

Contact Supplier for a service

No water Water has been

turned off

Blocked filter

Check Mains water supply

Replace filter cartridge.

Water boilers | Water chillers | Boil/Hot units | Boil/Hot/Chill units | Parts & Accessories

For more information about Ecoboil and our products,

visit our website or contact us:

Ecoboil Appliances Limited

Phone [phone]

Fax [phone]

Mail P.O. Box 940, Pukekohe 2340

Web www.ecoboil.co.nz