Ecoboil EBE, EBC Fusion Series, Fusion EB WP30, UBFKI, EB FM Installation And Maintenance Instructions Manual

EBC Fusion Series

Automatic Under Bench Boiling & Chilled Water

Installation and maintenance instructions

Please read prior to installation

WHAT’S IN EACH BOX:

BOX 1: BOX 2:

1 x EBE Boiling Unit 1 x EC 30 Arctic Chiller Unit
1 x EB WP30 Fusion Boil/Chill Tap 2 x EB 400 JG Connector
1 x UBFKI 10B Filter Kit
1 x EB FM 350 kPa PLV
1 x EB 316 Brass fitting kit
1 x Boiling Water Warning Label

Important

This unit must be installed by an authorised plumber

The unit to be connected in accordance with AS 3500.4.1

or AS/NZS 3500.4.2

Do not turn on power to these units until water is flowing

from the tap

Please leave these instructions with the owner

Water boilers | Water chillers | Boil/Hot units | Boil/Hot/Chill units | Parts & Accessories

Prior to installation

• Flush main water supply inlet line prior to making connections.

• Only teflon tape to be used where necessary, under no circumstances is

plumbing paste to be used.

• When fitting this unit in a cupboard of small proportions, please note that the
unit does omit heat. We recommend a vent is fitted.

• Do not connect to the boiler unit to the hot water line or the fire hydrant supply,
to do so will void the warranty.

• Requires 2 x 3 pin 10 amp power sockets.

Product Information

The boil unit is fitted with a computerised element and boil dry protection. The
computer is set at 95 Degrees C, altitude will alter the boiling point.

• The 350 kPa Pressure Limiting Valve supplied must be fitted.

• We recommend changing the water filter cartridge every 12 months.

• We recommend the cleaning and servicing of the units every 24 months, or

every 12 months in hard water areas.

• If the supplied power cord is damaged it must be replaced by an electrician

• This configuration requires Minimum Inlet Pressure 260 kPa.

Installation Instructions

1. Do not plug in the units or turn on the power until the installation

process is complete.

2. Position the Fusion Boil & Chill tap at the rear of the sink in a workable

location relative to the mixer. Cut a 38mm hole to facilitate mounting
of the tap. Secure the tap by tightening the bracket securing nuts supplied.

3. Position the Boil unit underneath the sink in a position that does not

require extensions to be made in the installation hoses that are
permanently affixed to the bottom of the Fusion Boil & Chill Dispenser
Tap. The Boil unit hoses may be cut to fit, but never extended.

4. Position the Chiller unit underneath the sink so that the chiller air-intake

is as close as possible to the front of the cupboard. The cupboard floor
which extends past the toe-board must have a slot cut into it to provide the
necessary ventilation (pref at least 20mm wide by 3/4 the width of the
cupboard door). The white inlet and outlet hoses from the Boil & Chill

Dispenser Tap can be extended in length if necessary.

5. Secure the 10” Filter with the bracket and screws provided to the

cupboard wall in a handy position relative to the mains inlet line as shown,
taking careful note of which ports are Outlet and Inlet

6. The filter cartridge comes with quick fit John Guest connections, push

the correct inlet/outlet tubes ends into the fittings and pull back carefully
to secure.

7. Connect the hoses on the Fusion Tap to the units as follows:

The three hoses taped together are all inlet hoses, one white, one blue and
one black, ensure these are connected first.
a. 1/4” Blue hose: connect to Outlet port of Water Filter. Using extra blue hose

provided, connect the Inlet Port of the Water Filter to the outlet port of the
PLV via the brass adaptor supplied.
b. 1/4” Black hose connect to the 1/4” brass connector on the top of the Boil
Unit marked “Inlet”.
c. 1/4” White hose: connect to the 1/4” quick fit connector on top of the Chiller

Unit marked “Inlet”.

Then connect the following hoses:

d. 5/16” Copper Pipe: connect to the 5/16” brass connector on top of the Boil
Unit marked “Outlet”.
e. 1/4” Orange silicon hose: push-fit over the end of the extended copper pipe
marked “Vent” on Boil Unit.
f. 1/4” White hose: connect to the 1/4” quick fit connector on top of the Chiller

Unit marked “Outlet”.

Cut or extend all chiller hoses as necessary. Never install with sharp bends,
use a John Guest elbow if necessary.

8. Connect the mains water supply to the inlet port of the PLV using the

15mm Hex nipple and Crox nut supplied.

9. Connect the drain clamp supplied and fix to the waste S bend above the

water level using the rubber seal between the clamp and the waste pipe.
Push on the Opaque silicon tube.

To mains
water supply

10. Open water supply and turn on both Boiling & Chilled Water levers at

the Fusion boil/chill tap until water flows without air bubbles.

11. Plug both units into power points and switch on, allow 20 minutes

prior to testing and use.

12. Check for leaks at all connections and tighten if necessary.

13. Position ‘Caution Boiling Water’ label close to the tap to alert users to

take care when using the hot tap.

Trouble Shooting

SYMPTOM CAUSES ACTION

Water Overflowing
from tap Spout

Excessive Steam
from tap

Water not hot No power supply

Expansion chamber full

Low Inlet Pressure

Faulty Element Replace element

Run Tap for 5-10 minutes

Contact water supplier

Check and test power supply

Faulty element

Water not cold No power supply Check and test power supply

No water Water has been turned off

Blocked filter

Replace element

Check Mains water supply

Clean or replace filter cartridge

For more information about Ecoboil and our products,

visit our website or contact us:

Ecoboil Appliances Limited

Phone [phone]

Fax [phone]

Mail P.O. Box 940, Pukekohe 2340

Web www.ecoboil.co.nz

Water boilers | Water chillers | Boil/Hot units | Boil/Hot/Chill units | Parts & Accessories