ECLIPTEK E11C1 User Manual

Marketing Bulletin

DATE: May 20, 2003 TO: Affected Customers FROM: Mark Stoner RE: Product Termination

To all concerned parties, This bulletin is to notify all customers of the termination of the following Ecliptek series

effective May 14th, 2003:

Series Description Recommended Replacement

E11C1 Four Pad SMD PECL Oscillator, 5V E13C1 Four Pad SMD PECL Oscillator, 3.3V E13J1 or E13W1 E11C2 Six Pad SMD PECL Oscillator, 5V E11J2 or E11W2 E13C2 Six Pad SMD PECL Oscillator, 3.3V E13J2 or E13W2 E31C2 Six Pad SMD PECL VCXO, 5V E31J2 or E31W2 E32C2 Six Pad SMD PECL VCXO, 3.3V E32J2 or E32W2

Because of the circumstances surrounding this termination, there will be no end-of-life policy exercised. The series will be terminated with no purchasing or lifetime buy window available. All of us at Ecliptek Corporation apologize for any inconvenience this may have caused and can assure you we are taking measures to insure this will not happen again in the future.

Best Regards,

E11J1 or E11W1

Mark W. Stoner Director of Marketing Ecliptek Corporation

3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234

E11C1 Series

OBSOLETE

• PECL Output Oscillators

• 5.0V supply voltage

• 4 pad ceramic SMD package with J-leads

E11C1

• Stability to 20ppm

• Output Enable/Disable available

H 5.1 L 14.2 W 9.85

• Complementary Output available

• Available on Tape and Reel

NOTES

__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

ELECTRICAL SPECIFICATIONS

Frequency Range

Operating Temperature Range

Storage Temperature Range

Supply Voltage (V

Input Current

Logic Type

Frequency Tolerance / Stability

Output Voltage Logic High (V

Output Voltage Logic Low (V

Rise Time / Fall Time

Duty Cycle

Load Drive Capability

Logic Control / Additional Output

Enable/Disable Input Voltage

Start Up Time

RMS Phase Jitter

MANUFACTURER CATEGORY

ECLIPTEK CORP. OSCILLATOR E11C1 CERAMIC 5.0V

)

Inclusive of Operating Temp Range, Supply Voltage,

Load, and Aging @25°C over 10 years

)

20% to 80% of waveform

at 50% of waveform

of VCC-1.475V

No Connection

of VCC-1.165V

FJ = 12kHz to 20MHz

SERIES PACKAGE VOLTAGE CLASS REV.DATE

Maximum

Minimum

19.440MHz to 212.500MHz

0°C to 70°C or -40°C to 85°C

-55°C to 125°C

5.0V

100mA Maximum

100KH

±100ppm, ±50ppm, ±25ppm, or

±20ppm Maximum

2 nSeconds Maximum

50 ±10(%)

50 ±5(%)

50 Ohms into V

No Connect, Enable/Disable, or

Complementary Output

Enables Output

Disables Output: Logic Low,

Disables Complementary Output: Logic High

10 mSeconds Maximum

1 pSec Maximum

OS65 10/02

OSCILLATOR

±5%

-1.025VDC Minimum

-1.620VDC Maximum

-2.0V

800-ECLIPTEK www.ecliptek.com for latest revision

Specifications subject to change without notice.

152

FREQUENCY TOLERANCE & STABILITY/

OBSOLETE

OPERATING TEMPERATURE RANGE

C=±100ppm Maximum over 0°C to +70°C D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C G=±100ppm Maximum over -40°C to +85°C H=±50ppm Maximum over -40°C to +85°C

DUTY CYCLE

1=50% ±10%, 2=50% ±5%

PART NUMBERING GUIDE

E11C1 F 2 C - 155.520M TR

AVAILABLE OPTIONS

Blank=Tubes TR=Tape and Reel (Standard)

FREQUENCY

LOGIC CONTROL/ADDITIONAL OUTPUT

A=No Connect B=Enable/Disable C=Complementary Output

MECHANICAL DIMENSIONS

ALL DIMENSIONS IN MILLIMETERS

Pin 1: Complementary Output, No Connect, or Enable/Disable

TAPE AND REEL DIMENSIONS

ALL DIMENSIONS IN MILLIMETERS

TAPE

A B C D E F

24 ±.3 11.5 ±.1 10.75 ±.1 4 ±.2 2±.1

Pin 2: Case Ground Pin 3: Output Pin 4: Supply Voltage

F G H J K L

12 ±.1 B0* 1.5 +.1-0 A0* .4 ±.05 K0*

ENVIRONMENTAL/MECHANICAL SPECIFICATIONS

SUGGESTED SOLDER PAD LAYOUT

ALL DIMENSIONS IN MILLIMETERS

Tolerances = ±0.1

REEL

2.5 MIN

MARKING SPECIFICATIONS

1.5 MINN50 MINO20.2 MINP13±.2Q40 MIN

10 MIN

30.4 MAXU360 MAXV24.4+2-0

QTY/REEL

1000

*Compliant to EIA 481A

Characteristic Specif ication

Seal Integrity Bubble test in Per fluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only).

Solderability Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage.

Marking Permanency 10 Strokes with brush after 1 minute soak in solvent, 3 times.

Shock Random drop on hard wooden plate 3 times from a height of 20cm.

Vibration Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours.

MANUFACTURER CATEGORY

ECLIPTEK CORP. OSCILLATOR E11C1 CERAMIC 5.0V

800-ECLIPTEK www.ecliptek.com for latest revision

Line 1: ECLIPTEK

Line 2: XX.XXX M

Frequency in MHz (5 Digits Maximum + Decimal)

Line 3: XX Y ZZ

Week of Year Last Digit of Year Ecliptek Manufacturing Identifier

SERIES PACKAGE VOLTAGE CLASS REV.DATE

Specifications subject to change without notice.

153

OS65 10/02

E11C2 Series

OBSOLETE

• PECL Output Oscillators

• 5.0V supply voltage

• 6 pad ceramic SMD package with J-leads

E11C2

• Stability to 20ppm

• Output Enable/Disable available

H 5.1 L 14.2 W 9.85

• Complementary Output available

• Available on Tape and Reel

NOTES

ELECTRICAL SPECIFICATIONS

Frequency Range

Operating Temperature Range

Storage Temperature Range

Supply Voltage (V

Input Current

Logic Type

Frequency Tolerance / Stability

Output Voltage Logic High (V

Output Voltage Logic Low (V

Rise Time / Fall Time

Duty Cycle

Load Drive Capability

Logic Control / Additional Output

Enable/Disable Input Voltage

Start Up Time

RMS Phase Jitter

)

Inclusive of Operating Temp Range, Supply Voltage,

Load, and Aging @25°C over 10 years

20% to 80% of waveform

at 50% of waveform

of VCC-1.475V

No Connection

of VCC-1.165V

FJ = 12kHz to 20MHz

Maximum

Minimum

19.440MHz to 212.500MHz

0°C to 70°C or -40°C to 85°C

-55°C to 125°C

5.0V

100mA Maximum

100KH

±100ppm, ±50ppm, ±25ppm, or

±20ppm Maximum

-1.025VDC Minimum

-1.620VDC Maximum

2 nSeconds Maximum

50 ±10(%)

50 ±5(%)

50 Ohms into V

No Connect, Enable/Disable,

Complementary Output, or

Complementary Output and Enable/Disable

Enables Output

Disables Output: Logic Low

Disables Complementary Output: Logic High

10 mSeconds Maximum

1 pSec Maximum

OSCILLATOR

±5%

-2.0V

MANUFACTURER CATEGORY

ECLIPTEK CORP. OSCILLATOR E11C2 CERAMIC 5.0V

800-ECLIPTEK www.ecliptek.com for latest revision

SERIES PACKAGE VOLTAGE CLASS REV.DATE

Specifications subject to change without notice.

154

OS66 10/02

+ 9 hidden pages

ECLIPTEK E11C1 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual