Eclipse - Fujitsu Ten CD5433 User Manual

OWNER'S MANUAL

We appreciate your purchase of this receiver.

Please read through this manual for correct operation.

We suggest that after reading it you keep this manual

in a safe place for future reference.

ESN E5 High-Power CD Receiver with

Multi Control and Remote

MODEL CD5433

For your safety in using the

Warning

Caution

Warning

CD5433

Warnings and caution signs, illustrated below, are posted throughout this manual as well as on the CD5433. They show safe and correct ways to handle the product so as to prevent personal injury to you and others and avoid damage to property.

Before reading through the manual, take time to read through and learn the important information listed in this section.

This sign indicates a situation in which incorrect handling through disregard of a sign might result in death or serious personal injury.

This sign indicates a situation in which incorrect handling through disregard of a sign might result in personal injury or may result solely in damage to property.

• Do not modify this system for use other than that specified herein. Also, do not deviate from the installation procedures described herein; Eclipse will not be held liable for damages including, but not limited to serious injury, death or property damage resulting from installations that enable unintended operation.

• This unit is intended for operation in DC 12-volt, negativegrounded vehicles only. Never use it in 24-volt vehicles such as heavy trucks or diesel cars with cold-region specifications.

• Do not change CDs while driving. Doing so may result in an accident.

• Do not place the vinyl storage bag over a person. It may cause a serious accident or death by suffocation.

• Do not adjust the controls while driving the car. To adjust the controls, stop the car in a safe location.

• To prevent accidents, store batteries for the remote control out of the reach of small children. In case a child swallows a battery, consult a physician immediately.

• Do not disassemble or rebuild this product. Doing so may cause an accident, fire or electrical shock.

• When it is necessary to replace the fuse, always use a fuse of the correct rating (number of amperes). Use of fuses with higher amperage ratings may cause a fire.

• Do not operate the product in a malfunctioning condition, for instance, when the audio does not play. Doing so may result in an accident, fire or electrical shock.

• If an abnormal situation occurs, such as foreign matter entering or liquid splashing on the product, or smoke or a strange odor emitting from the unit, shut off the product immediately and consult the dealer from whom you purchased it. Continued operation may cause an accident, fire or electrical shock.

• Do not install this product in locations where it may obstruct the driver's view, or where it may endanger passengers in the vehicle. Otherwise, an accident or injury may result.

• Do not install this product in locations where it may interfere with the operation of the steering wheel, shift lever, brake pedal, etc. Otherwise, an accident or injury may result.

• When installing this product, never use existing nuts or bolts that secure parts of the fuel tank, or the steering or braking systems. Otherwise improper steering or braking or a fire may result.

Warning

• To prevent a short circuit from occurring, disconnect the battery's negative terminal before installing this product. Otherwise, an electric shock or injury may result.

• When using an existing nut and/or bolt from the vehicle to ground this product, do not use any that secure parts of the steering or braking systems. Otherwise, an accident may result.

• Bundle cables and harnesses with electrical tape or wire ties to prevent them from interfering with moving parts. If they should entangle the steering wheel, shift lever or brake pedal, an accident may result.

• Never supply power to another electrical appliance by splicing or tapping into this product's power lead (wire). Otherwise, the current capacity of the wire will be exceeded, resulting in a fire or electric shock.

• Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric shock may result.

• When installing the product into a vehicle with a passenger side air bag, do not secure it to the air bag's cover or in places where it may impede air bag deployment. Otherwise, proper air bag operation may not be ensured in the event of an accident, causing injury or death.

• When making holes using a drill or similar tool, be sure to wear protective eyewear. Otherwise, an injury such as loss of eyesight may result.

• Exposed wires must be insulated with electrical tape. Otherwise, a short circuit, fire, or electric shock may result.

Warning

• Play the audio at a moderate volume level that permits you to hear sounds from outside the car. Driving without being able to hear outside sounds may result in an accident.

• Keep foreign objects out of the disc slot. They may cause fire or electrical shock. Another possibility is that discs may be damaged or become stuck.

• Do not stick your fingers or hands into the disc slot. Doing so may cause personal injury.

• This product must be operated only as on-board equipment, or it may cause electrical shock or injury.

• Do not play distorted sounds for long periods of time; the speakers may overheat and cause a fire.

• This product uses an invisible laser light. In case a problem develops, be sure to consult the dealer from whom you purchased the product. Do not disassemble or rebuild the unit; rebuilding it may expose you and others to a dangerous laser emission (which would damage eyesight) or cause an accident.

• Never use batteries other than those specified. Do not mix new and old cells. Doing so may cause a fire or personal injury due to a battery explosion or chemical leaks.

• Pay attention to the (+) and (

) polarity of the battery when installing them in the product. Incorrect installation may cause personal injury or product damage spoilage due to a battery explosion or chemical leakage.

• For best results, this product should be installed by a professional installer. Contact the dealer whom you purchased the product for an appointment.

• When installing this product, be sure to use the supplied mounting hardware. If parts other than those supplied are used, the unit may be damaged internally, or may not be held in place securely and become dislodged.

Caution

• Avoid installing this product in places where it may get wet, such as near windows, or in places that are moist or dusty. Presence of liquid, moisture or dust inside this product can cause short circuiting, resulting in smoke or fire.

• Do not install this product in locations where it cannot be fastened securely, such as places subject to frequent vibration. Otherwise, it may become dislodged and cause an accident or injury.

• Do not block this product's vent or heat sink. If either is blocked, excessive heat build-up may occur and cause a fire.

• If this product is not connected properly, a short circuit, fire or accident may occur.

• When routing cables, use care so that they do not contact sharp metal parts such as brackets or screw tips. Otherwise, a short circuit, electric shock, fire or accident may result.

• Do not obstruct the vent on this product. If blocked, excessive heat build-up may occur and cause a fire.

Caution

Table of Contents

Operating precautions...............................................10

Notes on operation .......................................................................10

About compact discs ....................................................................11

About cleaning a CD ....................................................................13

Names of controls and parts ....................................14

ESN (Key CD) security operating procedure ..........15

How to program the Key CD ........................................................15

How to cancel the Key CD ...........................................................16

How to change the Key CD ..........................................................17

How to resume normal operation (ESN security lock out)............17

What happens if an incorrect CD is inserted? ..............................18

How to turn the security indicator on/off .......................................19

How to read the Electronic Serial Number ...................................19

Basic operation ..........................................................20

Turning the power on and off .......................................................20

Listening to a CD..........................................................................21

Listening to the tuner....................................................................22

Adjusting audio volume ................................................................23

Switching audio control modes.....................................................24

Enabling the loudness control ......................................................25

Making changes with Display Adjustment Mode ..........................26

Making changes with Function Mode ...........................................27

Making changes with Sound Adjustment Mode ...........................30

Others...........................................................................................33

How to operate the CD player..................................34

Listening to CDs ...........................................................................34

Advancing to the next track or returning to the beginning of

the track being played ..................................................................35

Fast Forward/Rewind ...................................................................35

Playing the beginning of tracks (SCAN) .......................................35

Repeating the same track (REPEAT)...........................................36

Playing tracks in random order (RANDOM) .................................36

Ejecting the disc ...........................................................................37

Creating a title for a CD................................................................38

Changing a previously set title .....................................................40

Deleting a previously created title ................................................41

Displaying CD TEXT ....................................................................42

How to operate the MP3 player ................................43

About MP3....................................................................................43

Listening to MP3 file .....................................................................46

Advancing to the next track (file) or returning to the beginning of

the track (file) being played ..........................................................47

Skipping to the next or previous folder .........................................47

Return to the root directory of the CD ..........................................47

Playing the beginning of files (SCAN) ..........................................48

Repeating the same file (REPEAT)..............................................48

Playing files in random order (RANDOM) ....................................49

Displaying title ..............................................................................49

How to operate the tuner...........................................50

Tuning to a station........................................................................50

Entering stations into memory automatically

(The automatic preset mode: ASM) .............................................51

Manually setting stations into memory .........................................52

Preset station scan.......................................................................53

FM reception characteristics ........................................................54

How to use the Card remote control........................56

Precautions in use of the remote control......................................56

Cleaning the remote control .........................................................56

Turning the power on/off ..............................................................57

Adjusting the audio volume ..........................................................57

Switching playback modes ...........................................................58

How to play the tuner ...................................................................58

How to play CDs...........................................................................59

Enabling the optional E-COM feature...........................................60

Switching the remote control settings...........................................61

Replacing the battery ...................................................................62

How to use an optional NOB remote control ..........63

Turning the power on/off ..............................................................63

Adjusting the audio volume ..........................................................63

Switching playback modes ...........................................................64

How to play the tuner ...................................................................64

How to play CDs...........................................................................65

Illuminating the NOB remote control ............................................66

Enabling the optional E-COM feature...........................................66

Switching the remote control settings...........................................67

Replacing the battery ...................................................................68

How to operate the receiver with an optional

CD changer connected..............................................70

Listening to a CD..........................................................................70

Advancing to the next track or returning to the beginning of

the track being played ..................................................................70

Fast Forward/Rewind ...................................................................70

Playing the beginning of tracks (SCAN) .......................................71

Repeating the same track (REPEAT)...........................................71

Playing tracks in random order (RANDOM) .................................72

Skipping to the next or previous CD.............................................72

Specifying a CD to play ................................................................73

How to operate the receiver with an optional

DSP/EQ unit connected.............................................74

How to operate the DSP functions ...............................................74

How to operate the EQ functions .................................................77

Others .........................................................................80

Connecting Portable Audio Players to the AUX Jack...................80

If you have a question:..............................................81

Displayed information (for troubleshooting)..................................82

Specifications ............................................................85

Before installation .....................................................86

Components .................................................................................86

Setting the system-selector switch ...............................................86

Installation angle ..........................................................................87

Mounting instruction .................................................88

Mounting the main unit .................................................................88

Names of lead wires and destinations .........................................90

System .........................................................................................91

Operating precautions

• For your safety, play only at volume levels that allow outside sounds to be heard.

• We recommend using with this player a disc with the logo shown to the left.

• You can play music CDs(CD-R/CD-RW) on this player. Be sure to use discs that have been properly processed. Depending on the editing equipment used, some discs may not play properly.

• Do not insert anything other than a CD into the disc slot. Do not insert any foreign objects, such as coins or credit cards, into the disc slot. Be especially watchful of children’s mischief in this regard.

• Avoid severe mechanical shock. When the player is subjected to severe vibration while traveling over a rough surface, playback may be intermittent. When a situation like this occurs, resume playback after returning to a smoother road.

• About dew condensation. In cold or rainy weather, just as the interior glass surface gets fogged, dew (water condensation) may also settle on the deck. When this occurs, disc playback may become intermittent or impossible. Dehumidify the air in the vehicle for a while before resuming playback.

• Cleaning the disc slot. The disc slot tends to get dusty. Clean it occasionally to prevent accumulated dust from scratching the discs.

Notes on operation

Operating precautions

• The signal recorded on a compact disc is read by a laser beam, so nothing touches the disc surface. A scratch on the recorded surface or a badly warped disc may cause deteriorated sound quality or intermittent playback. Observe the following precautions to ensure high quality sound performance:

• Do not leave an ejected disc in the disc slot for very long; the disc may warp. Discs should be stored in their cases and kept away from high temperature and humidity.

• Do not stick a piece of paper or tape on, nor write on or scratch either side of a disc.

• Discs spin at a high speed inside the deck. Keep cracked or warped discs out of the player to avoid damaging it.

• Avoid touching the recorded surface when handling a disc; handle discs by their edges.

About compact discs

Operating precautions

About CD accessories

• Do not use accessories (stabilizers, protective seals, laser lens cleaners, etc.) sold for “improving sound performance” or “protecting CDs.” The changes in CD thickness or outside dimensions made by these accessories may cause problems in the player.

About brand new CDs

• You may notice that some brand new discs are rough around the center hole or outside edge. Remove the rough edges with the side of a ballpoint pen, etc. Rough edges may prevent proper loading in the deck. Flakes from the rough edges may also stick to the recorded surface and interfere with playback.

Rough Edges

Ballpoint pen

Flakes

Recorded surface

Rough Edges

• Please be sure NOT to attach any ring-shape protector (or other accessory) to your discs. Those protectors are commercially available and said to protect disc and to improve sound quality (and antivibration effect), but they can do more harm than good in regular uses. The most common problems are Insert/Eject related problems and "No playback" problems due to the protector ring that came off in the disc mechanism.

Operating precautions

About borrowed CDs

• Do not use a CD with glue or remnants of adhesive tape or labels. They may cause the CD to get stuck inside or damage the deck.

How to remove CDs

• When removing the ejected disc, pull it straight out along the slot. Pressing downward in the process may scratch the recorded surface of the disc.

OKAY

NO GOOD

About irregularly-shaped CDs

• Specially-shaped CDs, like heart-shaped or octagonal CDs, cannot be played. Do not attempt to play them, even with an adapter, since they may damage the player.

• Use a commercially available compact disc cleaner to clean a CD, wiping lightly from the center to the edge.

• Do not use benzine, thinner, LP record spray or other cleaners on CDs. They may damage a CD’s finish.

XXXX

About cleaning a CD

Names of controls and parts

Front view

With the front open

Never place an object or rest your hands or the like on the front panel.

Names of controls and parts

Switches disc modes and switches to AUX mode.

Activates and deactivates mute.

Opens/closes front panel and adjusts angle.

Selects radio preset channels and performs disc mode

functions.

Turns the sound adjustment mode ON/OFF.

Turns screen adjustment mode ON/OFF and switches screen

display.

Automatically finds radio reception and fast forward/rewind.

Selects radio stations and CD tracks.

Returns to previous screen.

Turns function mode ON/OFF.

Resets deck functions to default settings.

Turns deck power ON/OFF.

Switches to radio mode and switches radio bands.

Adjusts volume and performs other functions.

Inserts compact discs.

[DISC] button

[E-COM] button*

[OPEN] button

Buttons [1] to [6]

[SOUND] button

[DISP] button

[SEEK /FAST ] button

[SEL] button

[RTN] button

[FUNC] button

[RESET] button

[PWR] button

[FM AM] button

[AUDIO CONTROL] button

Disc slot

*: Double function button "E-COM" & "MUTE" functions

①② ⑤⑥⑦③ ④

⑬⑫ ⑪⑩⑨⑦

⑮

⑧⑭

④

Caution

ESN (Key CD) security operating procedure

How to program the Key CD

Check that the Power is OFF.

Press and hold button [6], then the [FUNC] button, and hold both for more than one second.

A [SEC] message appears, then in two seconds it will change to [DISC]. The front panel opens; the CD5433 is now ready to accept your Key CD in the CD slot.

Insert the CD into the slot.

The front panel closes. A [SEC] message appears, the front panel opens, then the Key CD is ejected.

•If there is a problem with the inserted CD, an [ERR] message will appear for two seconds and the CD will be ejected. Reinsert the ejected CD.

•If a CD causes the [ERR] message to appear twice in a row, a [CHANGE] message will appear for two seconds. Try another CD.

•The Security indicator will flash whenever the vehicle’s ignition is switched off.

ESN (Key CD) security operating procedure

[FUNC] button

Button [6]

ATTENTION

ESN (Key CD) security operating procedure

How to cancel the Key CD

Turn OFF the Power.

Press and hold button [6], then the [FUNC] button, and hold both for more than one second.

A [SEC] message appears, then in two seconds it will change to [DISC]. The front panel opens; the CD5433 is now ready to accept your Key CD in the CD slot.

Insert your Key CD into the slot.

The front panel closes. A [CANCEL] message appears, the front panel opens, then the Key CD is ejected. The Key CD is cancelled.

•This process cancels the protection for the ESN deck.

•If power to the ESN deck is disconnected, then

reconnected, a Key CD will not need to be inserted in order to return the unit to normal operation.

•Inserting a CD other than the Key CD will not cancel the protection. Instead, the display will show [ERR] for two seconds, then the normal CD playback mode will activate.

[FUNC] button

Button [6]

ATTENTION

ESN (Key CD) security operating procedure

How to change the Key CD

First, cancel the existing Key CD.

Refer to “How to cancel the Key CD.”

Next, program a new Key CD.

Refer to “How to program the Key CD.”

How to resume normal operation (ESN security lock out)

If power is disconnected while ESN security is active (a Key CD was programmed), operation is disabled until power is restored and the unit unlocked. Follow this procedure to resume normal operation.

When the power is turned on after disconnecting the battery power, a [SEC] message will appear for two seconds. Thereafter, the message changes to [DISC] and the CD5433 is ready to accept your Key CD into the slot.

Insert your Key CD.

If the correct CD is inserted, an [OK] message will appear for two seconds and the CD will begin playing.

•If an incorrect CD is inserted, an [ERR] message will appear for two seconds, after which the CD will be ejected.

•You must use the same CD used for Key CD programming; a duplicate CD may not work properly.

ATTENTION

ESN (Key CD) security operating procedure

What happens if an incorrect CD is inserted?

An [ERR] message will be appear, then change to a flashing [DISC], then the CD will be ejected.

You will have five uninterrupted attempts to insert the correct CD.

Press the [FUNC] button.

You will have five more attempts the correct disc.

After the 5th incorrect attempt, the display reads [HELP].

If [HELP] appears on the screen, press button [6], then the [FUNC] button, and hold them for five seconds.

Number of errors: Numbers indicated the number of errors that occurred.

O Note O

If after 10 tries the correct Key CD is not inserted, the display reads [CALL800]; the unit must be returned to Eclipse to be reset. In this case, please contact your Eclipse dealer for assistance or call Eclipse directly at (800) 233-2216.

Button [6]

[FUNC] button

Your key CD can be easily forgotten. Write the album name in a reminder note (See Page 97).

ATTENTION

ESN (Key CD) security operating procedure

How to turn the security indicator on/off

With the power OFF, press button [2], then the [FUNC] button and hold both for more than one second.

[IND. FLASH] or [IND. -----] appears on the display.

[IND. FLASH] means the security indicator will flash when the vehicle’s ignition is off, and [IND. -----] means it will not. Repeat the above steps to reactivate the flash mode.

Once ESN security is activated, the indicator flashes whenever the vehicle’s ignition is turned off, warning potential thieves that the unit is protected. However, if you do not want this visible deterrent, it may be turned off.

How to read the Electronic Serial Number

Turn OFF the Power.

Press button [4], then the [FUNC] button, and hold both for more than one second.

[ESN] appears on the display, followed by an eight-digit number; this number is your electronic serial number (ESN). You may use this number to identify your Eclipse CD5433 in the event it is recovered after being stolen.

Button [2] Button [4]

[FUNC] button

Basic operation

When the power is turned on, the state used when the power was turned off such as CD and tuner playing is restored.

When the vehicle has no ACC position on the ignition switch, care is needed when turning off the deck. Follow Step 2 or Step 3 when turning off the power.

Turning the power on and off.

Turning the power on and off

When power is OFF, press [PWR] button.

The power will come ON.

When power is ON, press the [PWR] button for less than two seconds.

The power will go OFF and the deck will be in Standby.

When power is ON, press the [PWR] button for more than two seconds.

The power will go completely OFF.

This section covers basic operating procedures. For additional details, please refer to the sections on specific functions.

If a car is not equipped with an ACC position (for example, a European car), keep the [PWR] button depressed for more than two seconds.

Basic operation

[PWR] button

ATTENTION

Basic operation

Listening to a CD

Press the [OPEN] button.

The front panel opens.

Insert a CD into the disc slot, label side up.

The CD will immediately start playing.

When a CD is already loaded, press the [DISC] button to switch to the CD mode.

[OPEN] button

[DISC] button

ATTENTION

Basic operation

Listening to the tuner

Press the [FM AM] button.

This will turn the tuner on.

Press the [FM AM] button to switch to the desired FM or AM bands.

Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed.

Turn the [SEL] button to the left or right to tune to a station.

If stations have been stored in memory, pressing a button from [1] to [6] will directly select a station. (Refer to the section “Manually setting stations into memory” on page 52)

Turn to the right: Tunes to higher frequencies. Turn to the left: Tunes to lower frequencies.

Press the [SEEK /FAST ] button to start the automatic station search.

[SEEK ] button: Starts searching toward higher frequencies. [FAST ] button: Starts searching toward lower frequencies.

[SEL] button

[FM AM] button

[SEEK ] button

[FAST ] button

Buttons [1] to [6]

ATTENTION

Basic operation

Adjusting audio volume

Turn the [AUDIO CONTROL] button to the left or right.

Turn to the right: Increases the volume. Turn to the left: Decreases the volume.

Press the [E-COM] button for more than one second if E-COM is connected and less than one second if E-COM is not connected to cut the volume or restore it instantly.

Do not adjust the volume or other controls while driving the vehicle. Do so only while parked in a safe location.

[E-COM] button

[AUDIO CONTROL] button

ATTENTION

Warning

Basic operation

Adjusts treble level. Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Emphasizes high sounds. Turn to the left: Softens high sounds.

TREB (TREBLE) Mode

Various audio control modes may be fine-tuned using this procedure.

Modes will switch in the order shown below each time the button is pressed.

Switching audio control modes

Press the [AUDIO CONTROL] button for less than one second to select the item to be adjusted.

[AUDIO CONTROL] button

Adjusts volume. Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Increases the volume. Turn to the left: Decreases the volume.

VOL (VOLUME) Mode

Adjusts bass level. Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Emphasizes low sounds. Turn to the left: Softens low sounds.

BASS Mode

VOL BASS* TREB* BAL FAD NON-F

*: These mode cannot be adjusted when the Hide-Away EQ/DSP

Sound Processor (2301) is connected.

Basic operation

To disable the loudness feature, repeat the above procedure to display the [LOUD OFF] indication.

Adjusts left/right speaker balance. Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Emphasizes right speakers. Turn to the left: Emphasizes left speakers.

BAL (BALANCE) Mode

Adjusts front/rear speaker balance. Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Emphasizes front speakers. Turn to the left: Emphasizes rear speakers.

FAD (FADER) Mode

Adjusts non-fader level (for connected sub-woofers, etc.). Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Increases level. Turn to the left: Decreases level.

NON-F (NON-FADER) Mode

The loudness control may be turned on to emphasize low and high frequencies at low volume levels. Loudness compensates for the apparent weakness of low and high frequencies at low volume by boosting the bass and treble levels.

Enabling the loudness control

Press and hold the [AUDIO CONTROL] button until the [LOUD ON] display appears on the screen.

[AUDIO CONTROL] button

ATTENTION

Basic operation

[DISP] button

[RTN] button

[SEL] button

This function allows adjustment of display contrast and changing illumination colors.

Enters Display Adjustment Mode.

Making changes with Display Adjustment Mode

Press the [DISP] button.

Adjust the display contrast to the best level in accordance with the angle of viewing.

Turn [SEL] button to select CONTRAST.

Press the [SEL] button.

Enters Contrast Adjustment Mode.

Turn [SEL] button to adjust contrast.

Turn to the right: Increases level. Turn to the left: Decreases level.

Press the [RTN] button.

At this time, other adjustments can also be made in Display Adjustment Mode.

Press the [DISP] button to exit Display Adjustment Mode.

543

Contrast adjustment

Turn [SEL] button to select ILL COLOR.

Press the [SEL] button.

The screen for changing the illumination color will appear.

Turn [SEL] button to select GREEN or RED.

Press the [RTN] button.

At this time, other adjustments can also be made in Display Adjustment Mode.

Press the [DISP] button to exit Display Adjustment Mode.

432

Changing Illumination Color

Basic operation

A variety of settings can be changed.

The function mode is activated.

Setting items will be displayed in the following order when the [SEL] button is turned to the right.

Making changes with Function Mode

Press the [FUNC] button.

*1:Cannot make settings other than for CD or CD changer

operation. (Refer to page 38 for details on CD operation.)

Refer to pages 61 and 67 for details on remote control operation.

Turn [SEL] button in either direction to display setting items for selection.

[SEL] button

[FUNC] button

DISC TITLE *

GUIDE TONE

REMOTE *

CLOCK DISP

CLOCK ADJ

Basic operation

[RTN] button[FUNC] button

[SEL] button

The receiver is set at the factory to emit a beep tone in response to button operation. The guide tone feature may be disabled in the following procedure:

Turn [SEL] button to select GUIDE TONE.

Press the [SEL] button.

The Guide Tone Mode will be switched ON/OFF.

Turn [SEL] button to select ON or OFF.

Press the [RTN] button.

At this time, other adjustments can also be made in Function Mode.

Press the [FUNC] button to exit Function Mode.

543

Disabling the guide tone feature (for button operation)

Switches the clock display to ON/OFF.

Turn [SEL] button to select CLOCK DISP.

Press the [SEL] button.

The clock display ON/OFF mode is activated.

Turn [SEL] button to select ON or OFF.

Press the [RTN] button.

At this time, other adjustments can also be made in Function Mode.

Press the [FUNC] button to exit Function Mode.

54321

CLOCK DISPLAY on/off

Basic operation

[SEEK ] button

[FAST ] button

[RTN] button[FUNC] button

[SEL] button

This receiver uses the 12-hour display notation.

Turn [SEL] button to select CLOCK ADJ.

Press the [SEL] button.

The clock adjustment mode is activated.

Turn [SEL] button to display the item to be selected for adjustment.

Hours, minutes or exact hour will be switched each time the button is turned.

Press the [SEEK /FAST ] button.

[SEEK ] button: Turns the time forward. [FAST ] button: Turns the time back. To set the clock to 0 minutes, 0 seconds (an exact hour), press the [SEEK /FAST ] button. For example: At 3:29: Pressing the [SEEK /FAST ] button returns to 3:00. At 3:30: Pressing the [SEEK /FAST ] button advance to 4:00.

Press the [RTN] button.

At this time, other adjustments can also be made in Function Mode.

Press the [FUNC] button to exit Function Mode.

654

Setting the Time

Basic operation

Used to adjust acoustic feature in the vehicle.

The sound adjustment mode is activated.

Making changes with Sound Adjustment Mode

Press the [SOUND] button.

Setting items will be displayed in the following order when the [SEL] button is turned to the right.

Turn [SEL] button in either direction to display setting items for selection.

*: This is displayed only if DSP/EQ (2301) is connected.

(Refer to page 74 for details on DSP/EQ operation.)

[SOUND] button

[SEL] button

DSP*

EQ*

BASS/TREB

X-OVER FR

X-OVER NF

Non-FADER

+ 68 hidden pages