Eclipse - Fujitsu Ten CD3200 User Manual

Page 1

Owner's Manual / Manuel de I'utilisateur / Manual del propietario

CD/USB Multi-Source Receiver with Bluetooth wireless technology

We appreciate your purchase of this receiver. Please read through this manual for correct operation. We suggest that after reading it you keep this manual in a safe place for future reference.

Nous vous remercions d'avoir acheté ce récepteur. Veuillez lire ce manuel afin d'utiliser votre appareil correctement. Nous vous recommandons de conserver ce manuel dans un endroit sûr afin de pouvoir le consulter ultérieurement.

Tras adquirir este receptor rogamos lea atentamente su manual para una correcta utilización del equipo. Igualmente, guarde dicho manual en un lugar adecuado para poder recurrir a él en caso de futuras consultas.

Page 2

For your safety in using the CD3200

Warnings and caution signs, illustrated below, are posted throughout this manual as well as on the CD3200. They show safe and correct ways to handle the product so as to prevent personal injury to you, others and to avoid property damage.

Before reading through the manual, take time to read through and learn the important information listed in this section.

This "Warning" sign indicates a situation in which incorrect

Warning

Caution

Please read all materials such as manuals and warranties that have come with the product. Eclipse will not be held liable for unsatisfactory product performance due to failure to follow these instructions.

WARNING

● Do not modify this system for use other than that specified herein. Also, do not deviate from the installation procedures described herein; Eclipse will not be held liable for damages including, but not limited to serious injury, death or property damage resulting from installations that enable unintended operation.

● This main unit requires 12V DC and should only be installed in a vehicle with a 12V negative ground electrical system. Any other installation may cause a fire or other severe damage to the main unit and the vehicle.

● Never install this main unit where it will interfere with safe operation of the vehicle. Never block the drivers' view. Do not install main unit where it may interfere with operation of the brakes, the steering or any safety equipment, including seat belts and air bags.

● Before drilling holes in a vehicle for installation, you must confirm the locations of pipes, tanks, electrical wiring, and other vehicle systems and components to ensure that there will be no interference or contact. In addition, you must also apply rust prevention and leak prevention measures at the drilling area. Otherwise, fire or electric shock could occur.

● When installing main unit do not remove or alter existing vehicle fasteners, including nuts, bolts, screws, clips, and fittings. Never detach, move or alter existing vehicle wiring, including electrical grounds and straps. Alteration of existing vehicle components may make vehicle unsafe to operate.

● Before installation, remove the negative (-) battery terminal to prevent shocks, electrical arcing, fires, and damage to vehicle wiring and the main unit you are installing.

● Secure wiring with tape or plastic ties so that wires do not interfere with vehicle operation, including brake pedal, gear shifter and steering. Position wires so that they will not be rubbed, abraded, or damaged by moving vehicle components, including power seats.

● To avoid main unit and vehicle damage, including fire, never supply power to the installed main unit in a way which will overload the capacity of an existing vehicle circuit. Never leave a power supply wire or connection uninsulated. Always install supplied fuses, circuit breakers, and relays.

handling or disregard of this sign might result in death or serious personal injury.

This "Caution" sign indicates a situation in which incorrect handling or disregard of this sign might result in personal injury or may result solely in damage to property.

Page 3

For your safety in using the CD3200

WARNING

● Air bags are vital safety equipment. Never install the main unit in a way which will alter air bag wiring or interfere with air bag deployment. Air bags must function properly in the event of an accident.

● When installation is complete, test all vehicle electrical systems for proper operation, including lights, horn, brake lights, and emergency flashers.

● For your protection, never use a power drill without safety glasses or goggles. Debris or broken drill bits may cause severe eye injuries, including blindness.

● Use electrical tape to insulate the ends of all wires, even if not used. Proper insulation prevents arcs, shocks and fires.

● Some equipment or devices require the use of batteries. Never install or place this type of equipment where young children can get access to batteries. If a battery is swallowed, seek medical attention immediately.

● When vehicle is moving, never take your eyes off the road to make adjustments to the main unit. You must pay attention to the road to avoid accidents. Do not let the operation or adjustment of the main unit distract you from proper vehicle operation.

● The driver should not look at the screen while driving. Accidents may result if you are not paying attention to the forward direction.

● Do not put foreign objects in the loading slot of disc or USB input terminal. Fires or shocks may result.

● Do not disassemble or alter this main unit. Accidents, fires or shocks may result.

● Do not let water or foreign objects enter the internal parts of this main unit. Smoke, fires or

shocks may result.

● Pay attention to where the remote control is left. Traffic accidents or problems with driving may result if the remote control makes its way under the foot pedals etc. when the vehicle is in motion.

● Do not use when abnormal operation occurs (the screen is not lit or no sound comes out). Accidents, fires or shocks may result.

● Always replace fuses with fuses of identical capacity and characteristics. Never use a higher capacity fuse than the original. Using incorrect fuse specifications may cause a fire or severe damage.

● If foreign objects or water enters the main unit, smoke comes out, or there is a strange odor, stop using it immediately, and contact your dealer. Accidents, fires, or shocks may result if you continue to use it in these conditions.

● The driver should not change the CD or USB memory while driving. As accidents may result if you are not paying attention to the forward direction, first stop the vehicle at a safe location and then proceed.

● Plastic bags and wrappings may cause suffocation and death. Keep away from babies and children. Never put bag over your head or mouth.

Page 4

For your safety in using the CD3200

CAUTION

● Wiring and installing this main unit requires expertise and experience. Professional installation is recommended. Consult with your dealer or a professional installer. Incorrect wiring may damage the main unit or interfere with safe vehicle operation.

● Use only the accessory parts as specified. Using other parts may cause damage to the main unit or cause parts to dislodge and/or detach unexpectedly.

● Do not install the main unit in places where it may get dew condensation on (around the air conditioning hose, etc.), come in contact with water, or in condition of high moisture, dust or oily smoke. If water, moisture, dust or oily smoke enters this main unit, smoke, fires or malfunctions may result.

● Avoid installing in places where it cannot be fastened securely or where there are strong vibrations. Also, if you installed the main unit with double-sided tape, first wipe away dirt and wax from the installation area. Otherwise, the main unit may come loose due to vibration while driving, causing problems for driving and resulting in traffic accidents or injuries.

● Do not install in places with direct sunlight or where it will be hit directly by hot air from the heater. This may increase the temperature of the interior of this main unit, resulting in fires and malfunctions.

● Do not obstruct the air flow of the heat sink or vents of this main unit. When the air flow of the heat sink or vents are obstructed, the interior overheats, and fires may result.

● Connect as specified in the installation manual. If not connected normally, fires or accidents may result.

● When installing in vehicles equipped with air bags, check the manufacturer's cautions regarding operation to ensure proper operation of the airbags.

● Install wiring in a manner that will not allow them to be pinched by moving parts, damaged by screws, or damaged by metal parts. Accidents, fires and shocks may result from disconnection and electrical shorts.

● Avoid hot surfaces when wiring main unit. High temperatures may damage wiring, causing shorts, arcing and fires.

● When changing the installation location for this main unit, please consult the dealer where you bought it for safety reasons. Expertise is necessary for removal and installation.

● Keep volume to a reasonable level so that you can hear sounds from outside the vehicle, including warning sounds, voices, and sirens. Failure to do so may cause an accident.

● Be careful that hands and fingers are not pinched when closing display. Injuries may result.

● Do not put your hands or fingers into the loading slot of disc or USB input terminal. Injuries

may result.

● Do not touch the heat dissipating part of the amp. Burns may result from the heat of this part.

● Do not recharge dry batteries. Dry batteries may rupture, resulting in injuries.

● Do not use batteries other than those specified. Also, do not mix old and new batteries.

Injuries or pollution to the surroundings may result from battery ruptures and leakage.

Page 5

For your safety in using the CD3200

CAUTION

● When inserting batteries into the remote control, be careful with the polarity (positive/ negative), and insert them as indicated. If the battery polarities are incorrect, injuries and pollution to the surroundings may result from battery ruptures and leakage.

● Replace used batteries as soon as possible; they may leak and damage the remote control. Battery leakage can burn your skin or your eyes. Wash hands after handling.

● If alkaline solution from alkaline dry batteries makes contact with your skin or clothes, flush with clean water. If any of the solution gets in your eyes, also flush clean with water and then seek medical attention.

● Do not short, disassemble or heat the batteries, or place them in fire or water. Fire and injuries may result from battery rupture and leakage.

● Store the remote control in a place away from direct sunlight, high temperatures, and high moisture levels. The outer case may change shape, and the batteries may rupture and leak.

● Do not use this main unit except for in-vehicle use. Shocks or injuries may result.

● Be careful of the position of the volume when turning the power source ON. Hearing

damage may result if very loud noise is emitted when the power is turned ON.

● Do not operate under abnormal conditions such as when the sound is broken or distorted. Fires may result.

● This main unit uses invisible laser light. Do not disassemble or alter this main unit. If trouble occurs, contact the dealer where you bought the main unit. Altering this main unit may cause exposure to laser emissions (worsening eyesight), or result in accidents, fires or shocks.

● If the main unit is dropped or the cosmetics appear broken, turn off the power to the main unit and contact your dealer. If used in this condition, fires or shocks may result.

Page 6

For your safety in using the CD3200

Page 7

Table of Contents

For your safety in using the CD3200......................................... 2

Operating precautions.............................................................. 14

Names of controls and parts ................................................... 16

How to operate the CD/MP3/WMA player ............................... 22

How to operate the USB music file player.............................. 32

The Bluetooth audio function .................................................. 36

How to operate the tuner.......................................................... 42

How to use the remote control ................................................ 46

The Bluetooth hands-free function ........................................ 48

ESN security operating procedure.......................................... 60

How to operate the AUDIO CONTROL .................................... 64

How to operate the Sound Adjustment Mode ........................ 66

Making changes with Display Adjustment Mode................... 72

Making changes with Function Mode ..................................... 76

III

VII

VIII

XII

XIII

XIV

How to operate the main unit with an optional CD changer connected

How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only)

How to operate the tuner with an optional XM satellite radio tuner connected (U.S.A./CANADA only)

How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A./CANADA only)

How to operate the main unit with an optional Interface Adapter for iPod connected

...... 84

..... 86

..... 88

..... 92

...... 96

Others ...................................................................................... 100

If you have a question: ........................................................... 102

Specifications.......................................................................... 106

How to contact customer service.......................................... 108

XVI

XVII

XVIII

XIX

XXI

XXII

XXIII

Page 8

Table of Contents

For your safety in using the CD3200.................................................... 2

Operating precautions......................................................................... 14

Notes on operation ....................................................................................................... 14

Names of controls and parts............................................................... 16

Turning the power on and off........................................................................................ 18

Switching Audio Modes ................................................................................................ 18

Adjusting volume .......................................................................................................... 18

Switching Rotary Modes............................................................................................... 19

About a shortcut ........................................................................................................... 19

Creating a shortcut................................................................................................. 19

Using a shortcut ..................................................................................................... 20

Switching screen .......................................................................................................... 20

Operation assist function .............................................................................................. 20

Detaching the front panel ............................................................................................. 21

Using the detachable panel.................................................................................... 21

How to remove the detachable panel..................................................................... 21

How to attach the detachable panel....................................................................... 21

How to operate the CD/MP3/WMA player........................................... 22

About compact discs .................................................................................................... 22

About brand new CDs ............................................................................................ 22

About CD accessories............................................................................................ 23

About borrowed CDs.............................................................................................. 23

How to remove CDs ............................................................................................... 23

About irregularly-shaped CDs ................................................................................ 23

About cleaning a CD..................................................................................................... 23

About MP3/WMA .......................................................................................................... 24

What is MP3/WMA? ............................................................................................... 24

Playable MP3 file standards................................................................................... 24

Playable WMA file standards ................................................................................. 24

ID3/WMA tag.......................................................................................................... 25

Media ..................................................................................................................... 25

Format of discs....................................................................................................... 25

File names.............................................................................................................. 26

Multi-sessions ........................................................................................................ 26

Playing MP3/WMA ................................................................................................. 26

MP3/WMA playing time display.............................................................................. 26

Display order of MP3/WMA file/folder names ........................................................ 26

Listening to CD ............................................................................................................. 27

TRACK (FILE) UP/DOWN ............................................................................................ 27

FOLDER UP/DOWN..................................................................................................... 28

Returning to the root directory of the CD (MP3/WMA file)............................................ 28

FAST FORWARD/REWIND ......................................................................................... 28

Page 9

Table of Contents

SCAN/REPEAT/RANDOM ........................................................................................... 28

FOLDER SCAN/REPEAT/RANDOM............................................................................ 29

DISPLAYING TITLE ..................................................................................................... 29

Ejecting the disc ........................................................................................................... 30

How to operate the USB music file player ......................................... 32

About playable USB memory standards....................................................................... 32

Playable MP3 file standards................................................................................... 32

Playable WMA file standards ................................................................................. 32

Format of USB memory ......................................................................................... 33

How to operate the USB music file player .................................................................... 34

Listening to music files in USB memory ................................................................. 35

Disconnecting USB memory......................................................................................... 35

The Bluetooth audio function ............................................................. 36

About the Bluetooth audio function............................................................................... 36

About the Bluetooth specifications ............................................................................... 36

Supported Bluetooth specifications........................................................................ 36

Supported profile.................................................................................................... 36

What is Bluetooth? ....................................................................................................... 37

Listening to music......................................................................................................... 37

Stopping the music ....................................................................................................... 37

Pausing the music ........................................................................................................ 37

Selecting the music you want to listen to...................................................................... 38

Fast forward/rewind ...................................................................................................... 38

Bluetooth audio setup................................................................................................... 38

Displaying the BT Audio Set selection mode ......................................................... 38

Switching the Bluetooth audio mode on and off ..................................................... 38

Connecting the main unit and the portable device ................................................. 39

Disconnecting the main unit and the portable device............................................. 39

Displaying device information for the main unit...................................................... 40

How to operate the tuner..................................................................... 42

Listening to the tuner .................................................................................................... 42

Tuning to a station ........................................................................................................ 42

Operations during rotary mode..................................................................................... 42

Automatically storing stations into memory. (The automatic preset mode: ASM) ........ 43

Manually storing stations into memory ......................................................................... 43

Preset station scan ....................................................................................................... 43

Changing the reception sensitivity for automatic scanning........................................... 44

Changing the radio band location................................................................................. 44

How to use the remote control ........................................................... 46

Precautions in use of the remote control ...................................................................... 46

Cleaning the remote control ......................................................................................... 46

Replacing the battery.................................................................................................... 47

Page 10

Table of Contents

The Bluetooth hands-free function ................................................... 48

About the Bluetooth hands-free function ...................................................................... 48

About the Bluetooth specifications ............................................................................... 48

Supported Bluetooth specifications........................................................................ 48

Supported profile.................................................................................................... 48

What is Bluetooth? ....................................................................................................... 49

Selecting the Bluetooth hands-free mode .................................................................... 49

Making a call................................................................................................................. 49

Making a call by dialing a phone number ............................................................... 49

Making a call using preset dial ............................................................................... 50

Making a call using the incoming/outgoing call history .......................................... 50

Making a call using the phonebook........................................................................ 51

Making a call from the cell phone........................................................................... 51

Receiving a call ............................................................................................................ 51

Hanging up (refusing a call).......................................................................................... 51

Adjusting the volume .................................................................................................... 51

Adjusting the ring tone volume............................................................................... 51

Adjusting the voice volume .................................................................................... 52

Storing phone numbers in preset dial........................................................................... 52

Setting the Bluetooth hands-free function .................................................................... 52

Displaying the Phone Setting selection mode........................................................ 52

Registering a cell phone......................................................................................... 53

Delete a registered cell phone ............................................................................... 54

Connecting a registered cell phone........................................................................ 54

Disconnecting a cell phone .................................................................................... 55

Registering phone number in the phonebook ........................................................ 55

Setting Auto Answer............................................................................................... 56

Setting the ring tone ............................................................................................... 56

Setting Auto Answer for registered cell phones ..................................................... 56

Displaying device information for the main unit...................................................... 57

Enabling phone numbers to be input directly ......................................................... 57

Deleting data .......................................................................................................... 57

Changing the passcode ......................................................................................... 58

ESN security operating procedure ..................................................... 60

About ESN.................................................................................................................... 60

How to operate the ESN (Key CD) security.................................................................. 60

How to program the Key CD .................................................................................. 60

How to cancel the Key CD ..................................................................................... 60

How to change the Key CD.................................................................................... 61

How to resume normal operation (ESN security lock out) ..................................... 61

What happens if an incorrect CD is inserted? ........................................................ 61

How to turn the security indicator on/off ....................................................................... 62

How to read the Electronic Serial Number ................................................................... 62

How to operate the AUDIO CONTROL ............................................... 64

Switching audio control modes..................................................................................... 64

Page 11

Table of Contents

How to operate the Sound Adjustment Mode ................................... 66

About Sound Adjustment Mode.................................................................................... 66

About parametric EQ.............................................................................................. 67

About position selector........................................................................................... 67

About crossover ..................................................................................................... 68

Switching the sound adjustment mode......................................................................... 69

Parametric equalizer adjustment (PEQ) ....................................................................... 69

Setting preset EQ................................................................................................... 69

Adjusting the median frequency and the Q curve .................................................. 69

Position selector ........................................................................................................... 70

Crossover adjustment (X-Over).................................................................................... 70

Non-fader phase (Non-F Phase) .................................................................................. 71

Making changes with Display Adjustment Mode .............................. 72

Switching the Display Adjustment Mode ...................................................................... 72

Switching the brightness (Bright).................................................................................. 72

Changing illumination color .......................................................................................... 72

Changing display type (DISP Type) ............................................................................. 73

Changing Background (Background) ........................................................................... 73

Changing the sound meter (Sound Meter) ................................................................... 73

Importing display data (DISP Data) .............................................................................. 74

Changing the scroll type (Scroll Type).......................................................................... 75

Making changes with Function Mode ................................................ 76

Switching the Function Mode ....................................................................................... 76

Setting a station name/disc title.................................................................................... 76

Deleting a station name/disc title.................................................................................. 77

Setting the guide tone................................................................................................... 77

Setting clock display (Clock ON/OFF) .......................................................................... 77

Setting time (Clock Adjust) ........................................................................................... 78

Switching demonstration screen display (Demo) ......................................................... 78

Setting the steering remote function (U.S.A. only) ....................................................... 79

Reading steering remote data (U.S.A. only) .......................................................... 79

How to operate the main unit with an optional CD changer

connected ............................................................................................. 84

Listening to a CD .......................................................................................................... 84

Advancing to the next track or returning to the beginning of the track being played .... 84

Operations during rotary mode..................................................................................... 84

Fast Forward/Rewind ................................................................................................... 84

Playing the beginning of tracks (SCAN) ....................................................................... 84

Repeating the same track (REPEAT)........................................................................... 85

Playing tracks in random order (RANDOM) ................................................................. 85

Skipping to the next or previous CD ............................................................................. 85

Specifying a CD to play ................................................................................................ 85

Page 12

Table of Contents

How to operate the tuner with an optional HD Radio tuner

connected (U.S.A. only)....................................................................... 86

About HD Radio............................................................................................................ 86

Switching between displays when receiving HD Radio ................................................ 86

HD Radio reception settings......................................................................................... 86

How to operate the tuner with an optional XM satellite radio tuner

connected (U.S.A./CANADA only) ...................................................... 88

About XM satellite radio................................................................................................ 88

Selecting the radio mode.............................................................................................. 88

Selecting a channel ...................................................................................................... 88

Operations during rotary mode .............................................................................. 89

Category selection ................................................................................................. 89

Direct channel selection ............................................................................................... 89

Manually setting channels into memory ....................................................................... 89

Preset channel scan ..................................................................................................... 90

Switching displays when using the XM satellite radio .................................................. 90

Displaying the XM ID .................................................................................................... 90

How to operate the tuner with an optional SIRIUS satellite radio

tuner connected (U.S.A./CANADA only) ............................................ 92

About SIRIUS satellite radio ......................................................................................... 92

Selecting the radio mode.............................................................................................. 92

Selecting a channel ...................................................................................................... 92

Operations during rotary mode .............................................................................. 92

Category selection ................................................................................................. 93

Direct channel selection ............................................................................................... 93

Manually storing channels into memory ....................................................................... 93

Preset channel scan ..................................................................................................... 93

Switching displays when using the SIRIUS satellite radio............................................ 94

Displaying the SIRIUS ID ............................................................................................. 94

How to operate the main unit with an optional Interface Adapter

for iPod connected............................................................................... 96

Listening to iPod music files (If an iPod is not connected) ........................................... 96

Listening to iPod music files (If an iPod is connected) ................................................. 96

Advancing to the next music file or returning to the beginning of the music file

being played ................................................................................................................. 96

Fast forward/rewind ...................................................................................................... 96

Searching for a music file ............................................................................................. 97

Repeating the same music file (REPEAT).................................................................... 98

Playing music files in random order (SHUFFLE).......................................................... 98

Displaying text .............................................................................................................. 98

Page 13

Table of Contents

Others.................................................................................................. 100

Connecting a portable audio player to the AUX jack .................................................. 100

Switching the AUX mode on and off .................................................................... 100

Switching the input system................................................................................... 100

Changing auxiliary input sensitivity ...................................................................... 101

If you have a question: ...................................................................... 102

Displayed information (for troubleshooting)................................................................ 102

When you think there is a malfunction........................................................................ 104

Specifications..................................................................................... 106

How to contact customer service..................................................... 108

* For more information on the operation of E-iSERV (Area Shot, display data, steering

remote), refer to the ECLIPSE Website given below and download the operation manual. (URL:http://www.e-iserv.jp)

Page 14

Operating precautions

Notes on operation

• For your safety, play only at volume levels that allow outside sounds to be heard.

• Discs with the logo shown to the left can be played.

• You can play music CDs (CD-R/CD-RW) on this player. Be sure to use discs that have been properly processed. Depending on the editing format and software used, some discs may not play properly.

TEXT

• Do not insert anything other than a CD into the main unit. Do not insert any foreign objects, such as coins or credit cards, into the disc slot.

• Avoid severe mechanical shock. When the player is subjected to severe vibration while traveling over a rough surface, playback may be intermittent. When a situation like this occurs, resume playback after returning to a smoother road.

• About dew condensation. In cold or rainy weather, just as the interior glass surface gets fogged, dew (water condensation) may also settle on the main unit. When this occurs, disc playback may become intermittent or impossible. Dehumidify the air in the vehicle for a while before resuming playback.

• Cleaning the disc slot. The disc slot tends to get dusty. Clean it occasionally to prevent accumulated dust from scratching the discs.

Page 15

Page 16

Names of controls and parts

Front view

No. Button Name/Working

[ e (OPEN/EJECT)]

button

Opens/closes front panel and ejects CD.

[VOL] button

Adjusts volume.

[SELECT] button

Selects radio station and CD tracks.

Selects setting items.

[ENTER] button

Enters selected item.

[ /MENU] button

Switches to the [TEL] mode.

Switches to the Menu Selection mode.

[SCREEN/TEXT] button

Switches the screen pattern.

Switches the title display.

Page 17

Names of controls and parts

No. Button Name/Working

[Release] button

Detach the right end of the front panel from the body of the main unit.

[MUTE] button

Activates and deactivates mute.

Buttons [1] to [6]

Selects radio preset channels and performs disc mode functions.

No. Button Name/Working

[SOURCE/PWR] button

Switches audio mode. Turn the power on or off.

[RTN/BAND] button

Returns to previous screen.

Switches radio band.

[MODE] button

Switches to rotary mode.

III

No. Name/Working

Disc slot

Inserts compact discs.

CAUTION

Never place an object or rest your hands or the like on the front panel.

Page 18

Names of controls and parts

Turning the power on and off

When the power is turned on, the state used when the power was turned off such as CD and tuner playback is restored.

When the vehicle has no ACC position on the ignition switch, care is needed when turning off the main unit. Follow Step 2 or Step 3 when turning off the power.

Press the [SOURCE/PWR] button

while the power is OFF.

The power will come ON.

ATTENTION

When the main unit's power is turned on for the first time or if the battery terminals have been disconnected because of a reason such as vehicle maintenance and the power is then turned back on, the main unit will start up in FM1 mode. After this, the broadcast stations will be searched for automatically and stored in buttons [1] to [6].

Press the [SOURCE/PWR] button while the power is ON, for more

than one second, until you hear a beep.

The power will go OFF and the main unit will be in Standby.

If you press the [SOURCE/PWR] button again for more than two seconds, the power will go completely off.

While the power is ON, press and hold the [SOURCE/PWR] button

until the "ACC OFF" message is displayed.

The power will go completely OFF.

Switching Audio Modes

Press the [SOURCE] button for

less than one second.

Press the button to switch mode in the following sequence:

FM/AM → SIRIUS*1→ XM*1 → CD (MP3/WMA)

AUX

→ iPod*1→ BT-Audio*3→ FM/AM →www

*1: Cannot be selected if the corresponding

device is not connected to the main unit. *2: Not displayed if no disc is inserted. *3: Cannot be selected if the AUX mode or the

BT-Audio mode is not set to ON. For details,

refer to "Switching the AUX mode on and off"

on page 100 or refer to "Switching the

Bluetooth audio mode on and off" on page 38.

→ CDC*1→ USB*2→

Adjusting volume

Turn the [VOL] button to the left or

right.

Turn to the right:

Increases the volume.

Turn to the left:

Decreases the volume.

ATTENTION

Press the [MUTE] button for less than one second to mute the sound or restore it.

CAUTION

Do not adjust the volume or other controls

while driving the vehicle. Do so only while

parked in a safe location.

ATTENTION

If the vehicle does not have an ACC position, press the [SOURCE/PWR] button until the "ACC OFF" message is displayed.

Page 19

Names of controls and parts

Switching Rotary Modes

The [VOL] button can be switched to other functions. When the rotary mode is set to ON, you can switch from the volume adjustment function to the following functions by pressing the [VOL] button.

Source Function Page

FM/AM TUNE UP/DOWN 42 XM TRACK UP/DOWN 89 SIRIUS TRACK UP/DOWN 92 CDP/CDC Track search 27 MP3/WMA FILE search 27 USB FILE search 27 iPod Track search 97

For detailed information on the above functions, see the operation instructions for each related audio source.

Press the [MODE] button while the

main unit is set to any audio mode.

Rotary mode will switch ON. When rotary mode is set to ON, the rotary indicator will be displayed as follows.

rotary indicator

About a shortcut

Create a shortcut for frequently-used functions so that they can be recalled with a single operation.

Creating a shortcut

A shortcut can be created for one of the following MENU mode adjustment functions: sound adjustment mode, display adjustment mode, or function mode.

Switch to the mode that you want

to create a shortcut for.

See the explanation for each adjustment mode for more information on switching them.

• Sound Adjustment Mode: Page 69

• Display Adjustment Mode: Page 72

• Function Mode: Page 76

Press the [ /MENU] button for

more than one second.

A shortcut will be created. If the [ / MENU] button is held for less than one second, the previously set adjustment function will be restored.

III

If the [MODE] button is pressed again, or if no operations are performed for more than 10 seconds, the rotary mode will be cancelled.

ATTENTION

• If you attempt to create a shortcut for a hierarchy where this is not possible, the

system will beep twice when [ /MENU] button is pressed for more than one second.

• Depending on the audio mode and the system setting, it may not be possible to operate the shortcut function. In this case,

the system will beep twice when the [ / MENU] button is pressed.

• Only one shortcut function can be registered. If a shortcut has already been registered, its key will be deleted when a new shortcut is created.

Page 20

Names of controls and parts

Using a shortcut

Press the [ /MENU] button for

more than one second.

The Menu Selection mode will be activated.

Press the [SELECT] (Up/Down)

button to select SHORTCUT.

Press the [ENTER] button.

The mode for the shortcut created will be displayed.

Switching screen

The screen's display pattern can be switched.

Press the [SCREEN/TEXT] for less

than one second.

When the button is pressed, the screen pattern changes display type in the following order.

Motion picture → Motion picture off → Sound Meter → Display off → Motion picture → www

Pattern Display

Sound Meter

Display off

Displays the Sound Meter set in display adjustment mode (refer to page 73).

Displays a black screen.

Operation assist function

In menu mode, the screen displays help to guide you in carrying out operations.

The function button selected for adjustment is displayed.

Pattern Display

Motion picture

Motion picture off

Displays a screen showing the moving image set in display adjustment mode (refer to page 73) and information such as elapsed CD playing time and current audio mode status.

Displays a screen showing information such as elapsed CD playing time and current audio mode status.

Page 21

Detaching the front panel

Names of controls and parts

Using the detachable panel

The front panel of the main unit can be removed.

By removing this panel when you leave the vehicle, you can prevent the theft of the main unit.

How to remove the detachable panel

Press the [Release] button.

The right end of the front panel detaches from the body of the main unit.

Detaching the front panel

Hold the front panel and pull it toward you to remove it.

Put the front panel into the case.

Push to open the front panel case and put the front panel in it.

How to attach the detachable panel

Insert the left end of the front panel

into the main unit.

Engage the catch at the left end of the front panel with the lock on the main unit itself.

Attach the front panel.

Press the right end of the front panel until it clicks into place.

CAUTION

• If you drop the detachable panel or subject it to impact, it may be damaged or malfunction.

• Do not attempt to detach or attach the detachable panel while driving since this could cause an accident.

• Store the detachable panel in a location free from humidity, dust, and water.

• Do not leave the detachable panel in locations that are likely to become hot, like the dashboard and surroundings.

III

Page 22

Operation

How to operate the CD/MP3/WMA player

Operation

About compact discs

• The signal recorded on a compact disc is read by a laser beam, so nothing touches the disc surface. A scratch on the recorded surface or a badly warped disc may cause deteriorated sound quality or intermittent playback. Observe the following precautions to ensure high quality sound performance:

• Do not leave an ejected disc in the disc slot for very long; the disc may warp. Discs should be stored in their cases and kept away from high temperature and humidity.

• Do not adhere a piece of paper or tape. Do not write on or scratch either side of a disc.

• Discs spin at a high speed inside the main unit. Keep cracked or warped discs out of the player to avoid damaging the main unit.

About brand new CDs

Rough Edges

Ballpoint pen

Rough Edges

Flakes

Recorded surface

• Avoid touching the recorded surface when handling a disc; handle discs by their edges.

• You may notice that some brand new discs are rough around the center hole or outside edge. Remove the rough edges with the side of a ballpoint pen, etc. Rough edges may prevent proper loading in the main unit. Flakes from the rough edges may also stick to the recorded surface and interfere with playback.

Page 23

About CD accessories

How to operate the CD/MP3/WMA player

• Do not use accessories (stabilizers, protective seals, laser lens cleaners, etc.) sold for “improving sound performance” or “protecting CDs.” The changes in CD thickness or outside dimensions made by these accessories may cause problems in the player.

• Please be sure NOT to attach any ring-shape protector (or other accessory) to your discs. Those protectors are commercially available and said to protect disc and to improve sound quality (and antivibration effect), but they can do more harm than good in regular uses. The most common problems are disc insertion, disc ejections, and won't play problems due to the protector ring that came off in the disc mechanism.

About borrowed CDs

• Do not use a CD with glue or remnants of adhesive tape or labels. They may cause the CD to get stuck inside or damage the main unit.

How to remove CDs

• When removing the ejected disc, pull it straight out along the slot.

OKAY

NO GOOD

Removing the disc in a downward or upward angle may scratch the recorded surface of the disc.

About irregularly-shaped CDs

• Specially-shaped CDs, such as heart-shaped or octagonal CDs, cannot be played. Do not attempt to play them, even with an adapter connected, as they may damage the player.

About cleaning a CD

• Use a commercially available compact disc cleaner to clean a CD,

XXXX

• Do not use benzine, thinner, LP record spray or other cleaners on

wiping gently from the center to the edge.

CDs. They may damage a CD' s finish.

Page 24

Operation

About MP3/WMA

ATTENTION

The making of MP3/WMA files by recording from sources such as broadcasts, records, recordings, videos and live performances without permission from the copyright holder for uses other than personal enjoyment is prohibited.

What is MP3/WMA?

MP3 (MPEG Audio Layer III) is a standard format for audio compression technology. By using MP3, a file can be compressed to one-tenth the size of the original.

WMA (Windows Media compressed to a size smaller than MP3 files.

This main unit has limitations on MP3/WMA file standards and recorded media and formats that can be used.

Playable MP3 file standards

• Supported standards: MPEG-1 Audio Layer III

• Supported sampling frequencies:

44.1, 48 (kHz)

• Supported bit rate: 64, 80, 96, 112, 128, 160, 192, 224, 256, 288, 320 (kbps) * Supports VBR. (64~320 kbps) * Does not support free format.

• Supported channel modes: monaural, stereo, joint, dual

Audio) is format for audio compression technology. WMA files can be

Playable WMA file standards

• Supported standard: WMA Ver.7 WMA Ver.8 WMA Ver.9

• Supported sampling frequencies: 32, 44.1, 48 (kHz)

• Supported bit rate: 48, 64, 80, 96, 128, 160, 192, 256, 320 (kbps) * Supports VBR (48~192 kbps). * Does not support lossless compression. * Does not support WMA files recorded at a frequency of 48 kHz with a bit rate of 96 kbps.

Page 25

How to operate the CD/MP3/WMA player

ID3/WMA tag

MP3/WMA files have an “ID3 / WMA Tag” that allows input of information so that data such as song title and artist can be saved.

This main unit supports ID3v. 1.0, 1.1 and WMA tags.

Media

Media capable of playing MP3/WMA includes CD-R and CD-RW discs. Compared to CD-ROM media commonly used for music discs, CD-R and CD-RW discs are fragile in high temperature/high humidity environments and one section of the CD-R and CD-RW may become incapable of playback. Fingerprints or scratches on the disc may prevent playback or cause skipping during playback. Sections of a CD-R and CD-RW may deteriorate if left inside a vehicle for long periods of time. It is also recommended that CD-R and CD-RW discs be kept in a light-blocking case because the discs are vulnerable to ultra-violet light.

Format of discs

The format of discs to be used must be ISO9660 Level 1 or Level 2. Control items for this standard are as follows:

• Maximum layers in directory: 8 layers

• Maximum characters for folder names/file names: 32 (including “.” and 3 letter file extension)

• Allowable characters for folder names/file names: A~Z, 0~9, _ (underscore)

• Number of files possible on a single disc: 999

[Configuration example for CD supporting MP3/WMA]

Root directory (F1)

Folder 2

001.mp3

002.mp3

003.mp3

004.txt

005.mp3

F158

F159

Folder 158

Folder 159

001.mp3

002.mp3

Number of files possible on a single disc is 999.Files aside from MP3/WMA files (Example: 004.txt) also count as single files.

Folder 255

F255

• Total number of folders possible on a single disc: 255

• Maximum folders this main unit can recognize: 256*

*: A root directory is counted as one folder.

Page 26

Operation

File names

Only files with the MP3/WMA file extension “.mp3”, “.wma” can be recognized as MP3/WMA and played. Be sure to save MP3 files with the “.mp3” file extension. Be sure to WMA files with the “.wma” file extension. The “MP” letters of the file extension will be recognized whether entered as uppercase letters or lowercase letters.

CAUTION

If the “.mp3”, “.wma” file extension is attached to a file other than an MP3/WMA file, that file will be mistakenly recognized by the main unit as an MP3/WMA file and played, resulting in loud noise output that can damage the speakers. Be sure to avoid attaching the “.mp3”, “.wma” file extension to files that are not MP3/WMA files.

Multi-sessions

Multi-sessions are supported, and the playing of CD-R and CD-RW discs with MP3/WMA files added is possible. However, if files have been written onto a disc using “Track at once”, close the session or perform the finalization process. Standardize the format so that it does not change with each session.

Playing MP3/WMA

When a disc with recorded MP3/WMA files is inserted, the main unit first checks all the files on the disc. No sound is output while the main unit is checking the files on the disc. It is recommended that the disc be recorded without files other than MP3/WMA files and without unnecessary folders in order to speed up the checking of disc files by the main unit.

MP3/WMA playing time display

It is possible that playing time will not be correct, depending on the writing condition of the MP3/ WMA file. * It is possible that playing time will not be correct when VBR Fast Up/Down is operated.

Display order of MP3/WMA file/folder names

Names of MP3/WMA folders and files within the same level are displayed in the following order.

1.MP3/WMA folders displayed first, by ascending order of numbers, letters.

2.Files displayed next, by ascending order of numbers, letters.

Page 27

How to operate the CD/MP3/WMA player

Listening to CD

Press the [ e (OPEN/EJECT)]

button.

The front panel opens.

If a disc has already been loaded, the disc will be ejected.

Insert a CD into the disc slot, label

side up.

The front panel automatically closes and the CD will immediately start playing.

ATTENTION

• Playback may be intermittent when there is a scratch on a CD or when the recorded side is dirty.

• If a CD has already been loaded, press the [SOURCE/PWR] button for less than one second to switch to the CD mode. (For details, refer to "Switching Audio Modes" on page 18.)

TRACK (FILE) UP/DOWN

CD, MP3/WMA

Briefly press the [SELECT] (Right/

Left) button.

(Right):

Advances to the next track (file).

(Left):

Returns to the beginning of the track being played.

CD (Rotary mode)

Turn the [VOL] button.

(Right):

Advances to the next track.

(Left):

Returns to the beginning of the track being played.

CAUTION

Do not press the [ e (OPEN/EJECT)] button while a CD is being loaded. This could cause injuries or damage to the front panel.

NOTE

• When music data recorded in the normal way (CD-DA) is present on the same disc with MP3/WMA music files, the normally recorded music data will be played. To listen to the MP3/WMA music files, press [MODE] button for more than one second.

• MP3/WMA files which are not supported cannot be played. In this case, [NO SUPPORT] is displayed.

• The optional CD changer cannot be used to play MP3/WMA files.

MP3/WMA (Rotary mode)

Press the [MODE] button for less than one second to display the file

list.

Turn the [VOL] button to select the

file.

(Right):

Advances to the next track.

(Left):

Previews previous tracks.

Press the [ENTER] button.

Page 28

Operation

ATTENTION

For details on how to operate the rotary mode function, refer to page 19.

FOLDER UP/DOWN

MP3/WMA

Press the [SELECT] (Up/Down)

button.

(Up):

Selects the next folder.

(Down):

Selects the previous folder.

Returning to the root directory of the CD (MP3/WMA file)

In the root directory, when a file cannot be played, the system will return to the first file that can be played. (In the configuration example, the file is returning to 001.mp3. Refer to page 25.)

FAST FORWARD/REWIND

CD, MP3/WMA

Press and hold the [SELECT]

(Right/Left) button.

(Right):

Fast forwards.

(Left):

Rewinds.

SCAN/REPEAT/RANDOM

Press the [4 SCAN] button, the [5 RPT] button or the [6 RAND]

button.

The main unit will play the first 10 seconds of each track. To cancel, press button again.

CD, MP3/WMA

Press the [RTN/BAND] button.

The main unit will move to the root directory and the first music track (file) will be played.

ATTENTION

When there is no file to be played in the root directory, the file in the first folder is played.

Repeating the same track. To cancel, press button again.

Change the order of the tracks, and play them in random order. Press the button again to cancel this operation.

Page 29

How to operate the CD/MP3/WMA player

MP3/WMA

Press the [4 SCAN] button, the [5 RPT] button or the [6 RAND]

button.

The main unit will play the first 10 seconds of each file located in the same layer as the folder currently being played. Press the button again to cancel this operation.

Repeating the same file. To cancel, press button again.

The main unit will randomly play all files located in the same layer as the folder currently being played. Press the button again to cancel this operation.

ATTENTION

• During random playback, press the [5 RPT] button to repeat the track (file) being played. Press the [5 RPT] button again to cancel repeat play (and return to random play).

• Occasionally the same track will play two or more times. This is a normal operation and is not a sign of a problem.

• [SCAN], [REPEAT], or [RANDOM] will appear on the display when these functions are active.

FOLDER SCAN/REPEAT/ RANDOM

MP3/WMA

Press the [4 SCAN] button, the [5 RPT] button or the [6 RAND] button

for more than 1 second.

The first 10 seconds of the first song in each folder is played. To cancel, press button again.

The tracks in the same layer as the folder being played are played repeatedly. Press the button again to cancel this operation.

The files in all folders are played randomly. To cancel, press button again.

DISPLAYING TITLE

(TEXT supported CD's)

Press the [SCREEN/TEXT] button

for more than one second.

CD text will be scrolled on the display.

Page 30

Operation

MP3/WMA

Press the [SCREEN/TEXT] button

for more than one second.

Each time the button is pressed, the text will be displayed in the following order.

Folder Name/File Name

*: A maximum of 14 characters can be

displayed in the display area. The remaining characters can be displayed by scrolling. The folder name is displayed first. The file name can then be displayed by scrolling. After the file name has been displayed, the display will be fixed.

→ Tag

ATTENTION

• CD text cannot be displayed using CD changers (sold separately).

• If the CD came with a logo shown below, it is recorded with a disc title and track titles. These information will be displayed during playback.

Ejecting the disc

Press the [ e (OPEN/EJECT)]

button.

The front panel opens and the disc is ejected.

ATTENTION

If a loaded CD is not ejected, press the [ e (OPEN/EJECT)] button for more than five seconds with the front panel open to eject the disc.

Remove the disc and press the [ e

(OPEN/EJECT)] button.

The front panel closes.

CAUTION

• Do not drive with the front panel open. The panel may cause unexpected personal injury during a panic stop, or the like.

• Do not attempt to close the front panel by hand. Doing so may damage the panel.

• CD text, Folder name/file name or tag recorded with characters other than alphanumeric and symbols cannot be displayed.

Page 31

Page 32

Operation

How to operate the USB music file player

Operation

About playable USB memory standards

• Supported File System:

FAT 12/16/32

• Playable Audio Format:

MP3/WMA

• Max.Current:

500mA

• Compatibility:

USB1.1/2.0

• Correspondence:

USB mass storage class

Playable MP3 file standards

• Supported standards: MPEG-1 MPEG-2 MPEG-2.5 Audio Layer III

• Supported sampling frequencies: MPEG-1:32, 44.1 (kHz) MPEG-2:16, 22.05, 24 (kHz) MPEG-2.5:8, 11.025, 12 (kHz)

• Supported bit rate: MPEG-1: 32, 40, 48, 56, 64, 80, 96, 112, 128, 160, 192, 224, 256, 288, 320 (kbps) MPEG-2: 8, 16, 24, 32, 40, 48, 56, 64, 80, 96, 112, 128, 160 (kbps) MPEG-2.5: 8, 16, 24, 32, 40, 48, 56, 64, 80, 96, 112, 128, 160 (kbps) * Supports VBR. (8~320 kbps) * Does not support free format.

• Supported channel modes: monaural, stereo, joint, dual

Playable WMA file standards

• Supported standards: WMA Ver. 7 WMA Ver. 8 WMA Ver. 9

• Supported sampling frequencies: 8, 11.025, 12, 22.05, 32, 44.1 (kHz)

• Supported bit rate: 8, 16, 24, 32, 40, 48, 64, 80, 96, 128, 160, 192 (kbps) * Supports VBR (40~95 kbps) * Does not play DRM.

Page 33

How to operate the USB music file player

• Supported channel modes: monaural, stereo

Format of USB memory

The USB memory format must be ISO9660 Level 1 or Level 2. Standards are as follows:

• Maximum directory layers: 8 layers

• Maximum characters for folder names/file names: 128 (including “.” and 3 letter file extension)

• Allowable characters for folder names/file names: A~Z, 0~9, _ (underscore)

• Number of files possible on a single USB memory: 3000

[Configuration example for USB memory supporting MP3/WMA]

Root directory (F1)

Folder 2

001.mp3

002.mp3

003.mp3

004.txt

005.mp3

F498

F499

Folder 498

Folder 499

001.mp3

002.mp3

Number of files possible on a single USB memory is 3000. Files aside from MP3/WMA files (Example: 004.txt) also count as single memories.

Folder 999

F999

• Total number of folders possible on a single USB memory: 999

• Maximum folders this main unit can recognize: 1000*

*: A root directory is counted as one folder.

Page 34

Operation

How to operate the USB music file player

When a USB memory or a digital audio player with a USB terminal is connected to a USB connector, music files can be played from the USB memory.

USB connection terminal for USB memory or digital audio player.

Page 35

How to operate the USB music file player

Listening to music files in USB memory

Connect the USB memory to the

USB connector.

Switch to the USB mode.

For details, refer to "Switching Audio Modes" on page 18.

Operate the USB music file player.

The procedure for playing music is the same as that are used to play CDs. Refer to "How to operate the CD/MP3/ WMA player" (page 27 - 29).

ATTENTION

If the USB mode is changed to another mode and then returned to the USB mode, the player will return to the previous file played.

CAUTION

• Do not disconnect the USB memory or turn the ignition key to ACC OFF position while accessing the USB memory. Doing so may corrupt the data.

• Depending on the type connected, the USB memory may not work in some cases.

• The USB memory does not support multipartition. or USB hub.

• It is highly recommended to back up your data in case of accidental deletion.

• Install and use the USB device in a place that provides safe operation of the vehicle.

• The music files under the copyright protection cannot be played.

• When connecting a digital audio player to the USB connector, additional USB adaptors may be required.

Disconnecting USB memory

Disconnect the USB memory

parallel to the USB connector.

ATTENTION

Do not remove the USB memory while playing, reading or writing data.

CAUTION

Do not apply excessive force when removing the USB memory. Doing so may damage the USB connector and/or the USB memory.

Page 36

Operation

The Bluetooth audio function

Operation

About the Bluetooth audio function

The use of Bluetooth wireless communication technology enables a Bluetooth-compatible portable audio player (hereafter called "a portable device" ) to be used as a source for the main unit.

Once the portable device is connected to the main unit, it is possible to listen to music without directly operating the portable device.

Because the connection between the portable device and the main unit is wireless, cable connection is not needed.

• Before using a Bluetooth-compatible portable device (including cell phones) with the main unit, be sure to complete the “Setting the Bluetooth audio functions”. (See pages 38 and 39 for instructions)

• When the portable device has been connected to the main unit, the Bluetooth connection indicators will be displayed.

$NWGVQQVJ

EQPPGEVKQP

KPFKECVQT

$NWGVQQVJCWFKQ

EQPPGEVKQPKPFKECVQT

• If the portable device is used with other wireless devices, it may have a negative effect on the communication capabilities of both.

• The Bluetooth communication connection may cause the batteries in the portable device to lose their charge quickly.

About the Bluetooth specifications

The Bluetooth-compatible portable device to be connected to the main unit must be compatible with the following specifications. (However, depending on the models of the portable device, some of the functions may be limited.)

Supported Bluetooth specifications

Bluetooth Specification Ver.2.0

Supported profile

ATTENTION

• Noise may be experience when using the Bluetooth cell phone and Bluetooth audio.

• Depending on the version of Bluetooth, some cell phones may not be able to communicate with the main unit.

• Depending on the surrounding environment, the connection may become unstable, and the Bluetooth audio function may not be able to be operated from the main unit.

• A2DP (Advanced Audio Distribution Profile) Version 1.0: Profile for transmission of high quality sound

• AVRCP (Audio/Video Remote Control Profile) Version 1.0: Profile for control of AV equipment by remote-control

Page 37

The Bluetooth audio function

What is Bluetooth?

Bluetooth is a form of short-range wireless communication technology, used to connect cell phones and personal computers.

This technology enables hands-free calling and data transmission between Bluetooth-compatible devices.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

WARNING

For safety reasons, the driver must not operate the portable device while driving. Stop the vehicle in a safe location before operating the device.

CAUTION

• Do not leave the portable device inside a vehicle. (The temperature inside a vehicle may increase dramatically when it is exposed to extreme heat from the sun.)

• Do not use the portable device in a location close to the main unit. If they are too close together, the sound quality and the connection may be adversely effected.

Listening to music

Press the [SELECT] (Up) button.

The connected Bluetooth-compatible portable device starts to play music.

ATTENTION

• If the portable device is not connected to the main unit, its play function is disabled.

• If the portable device does not start playing, even after you have pressed the [SELECT] (Up) button, press the Play button on the portable device.

Stopping the music

Switch to another audio mode.

For details, refer to "Switching Audio Modes" on page 18.

ATTENTION

The portable device may continue to play music even if it is switched to another audio mode.

Pausing the music

Press button [1].

The music being played is paused.

Switch to the Bluetooth audio

mode.

For details, refer to "Switching Audio Modes" on page 18.

ATTENTION

Press the [SELECT] (Up) button or button [1] to start playing the music.

Page 38

Operation

Selecting the music you want to listen to

Press the [SELECT] (Right/Left)

button.

Right:

Advances to the next track.

Left:

Returns to the beginning of the track being played.

ATTENTION

Press the [SELECT] (Left) button repeatedly to return to previous tracks.

Fast forward/rewind

Press and hold the [SELECT]

(Right/Left) button.

Right:

Fast forwards.

Left:

Rewinds.

ATTENTION

The fast forwarding or rewinding will continue until the [SELECT] (Right/Left) button is released.

• Device INFO display:

Displays device information for the main unit.

Displaying the BT Audio Set selection mode

Press the [ /MENU] button for

more than one second.

The MENU selection mode is displayed.

Press the [SELECT] (Up/Down)

button to select FUNC.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select BT AUDIO Set.

Press the [ENTER] button.

The BT Audio Set selection mode is activated.

Switching the Bluetooth audio mode on and off

The Bluetooth audio function can be selected while in the audio mode.

Press the [SELECT] (Up/Down) button while in the BT Audio Set

selection mode to select ON or OFF.

Bluetooth audio setup

A variety of functions available when using the portable device can be set from the BT Audio Set mode.

• BT Audio setting: Bluetooth audio mode on and off.

• Connection setting: Main unit and portable device connectivity.

• Disconnection setting: Disconnects the main unit and the portable device.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select ON or OFF.

ON:

Enables BT-Audio

OFF:

Disables BT-Audio

Page 39

The Bluetooth audio function

Press the [RTN/BAND] button.

The portable device is set as a Bluetooth audio source.

ATTENTION

• The Bluetooth audio (BT-Audio) function

can only be selected in the audio mode when the BT Audio Set selection mode is set to ON.

• The default setting for the Bluetooth audio

mode is OFF (BT-Audio selection is disabled).

Connecting the main unit and the portable device

Press the [SELECT] (Up/Down) button while in the BT-Audio Set

selection mode to select Connect.

Press the [ENTER] button.

The "Waiting" message appears on the display.

ATTENTION

Press the [RTN/BAND] button to change the portable device to be connected. The BTAudio Set selection mode is activated again.

When the connection has been completed, the "COMPLETED"

message appears on the display.

The portable device is now connected to the main unit.

( and appear on the display.)

If the connection has not been successfully completed, the "FAILED" message appears on the display.

ATTENTION

• If the portable device is still connected, disconnect it.

• If the connection has not been successfully completed, and the "FAILED" message appears on the display, connect the portable device again, following the procedure from the BT Audio Set selection mode in Step 1.

• The passcode is a password used when connecting the portable device to the main unit.

• When the audio of the cell phone is connected, hands-free can be connected at the same time for some devices. If you want to be able to use the hands-free function, perform the hands-free connection procedure again.

Disconnecting the main unit and the portable device

Input the passcode using the

portable device.

The default setting value of the passcode is 1234.

ATTENTION

• For details on how to operate the portable device, read its instruction manual.

• Be sure to perform the connection of the portable device only while the "Waiting" message is on the display.

Press the [SELECT] (Up/Down) button while in the BT Audio Set

selection mode to select Disconnect.

Press the [ENTER] button.

The "Disconnect ?" message appears on the display.

Page 40

Operation

Press the [ENTER] button.

ATTENTION

If you do not want to cancel the connection, press the [RTN/BAND] button. The BT Audio Set selection mode is activated again.

When the disconnection has been completed, the "COMPLETED"

message appears on the display.

The main unit is now disconnected from the portable device.

( and disappear from the display.) However, will not disappear while Blutooth hands-free is connected.)

Displaying device information for the main unit

The name of the device (main unit), the passcode and the BD ADD (device address) can be displayed.

Press the [SELECT] (Up/Down) button while in the BT Audio Set

selection mode to select Device INFO.

Press the [RTN/BAND] button.

The BT Audio Set selection mode is activated again.

Press the [ENTER] button.

The name of the device and the passcode are displayed.

ATTENTION

Each time the [SCREEN/TEXT] button is pressed, the display changes in the following way. Device name / passcode ↔ Device name / BD ADD (device address)

Page 41

Page 42

Operation

How to operate the tuner

Operation

ATTENTION

• If stations have been stored in the memory, pressing a button from [1] to [6] will enable you to select a station. (Refer to "Manually storing stations into memory" on page 43.)

Listening to the tuner

Switch to tuner mode.

For details, refer to "Switching Audio Modes" on page 18.

Tuning to a station

There are both automatic and manual methods (one of each) for storing stations in memory. The main unit can store up to 24 stations in memory. There are 6 stations for AM and 18 stations for FM (6 each for FM1, FM2 and FM3) (initial settings).

Press and hold the [SELECT] (Right/Left) button. The device

starts to search for stations automatically.

Right:

Starts searching toward higher frequencies.

Left:

Starts searching toward lower frequencies.

ATTENTION

At times, it may be difficult to maintain optimum reception because the antenna attached to your vehicle is constantly in motion (relative to the broadcast antenna), encountering continuous variation in the strength of the radio signals received. Other factors affecting reception include interference from natural obstacles, buildings, etc. When an optional HD Radio tuner unit is connected, digital broadcasts have reception priority. (U.S.A. only)

Press the [RTN/BAND] button briefly (for less than one second)

to switch to the desired FM or AM band.

Radio bands will switch from FM1 → FM2 → FM3 → AM in order each time the button is pressed.

Press the [SELECT] (Right/Left)

button to tune to a station.

Right:

Tunes to higher frequencies.

Left:

Tunes to lower frequencies.

Operations during rotary mode

For the operation method in the Rotary mode, refer to page 19.

Page 43

How to operate the tuner

Automatically storing stations into memory. (The automatic preset mode: ASM)

Press the [SELECT] (Up) button for more than two seconds, until you

hear a beep.

The automatic preset mode starts.

"ASM ON" will appear on the display, and stations are automatically entered in memory under buttons [1] to [6].

These buttons are called preset buttons.

ATTENTION

• Pressing the preset buttons ([1] to [6]) allows you to make one-touch station selections. The frequency of the selected station is indicated on.

• When a new station is set in memory, the station previously set in memory will be deleted.

• If there are fewer than six receivable stations, the stations set in the remaining buttons will be retained.

Manually storing stations into memory

Store a station to a preset button.

Press the [SELECT] (Right/Left) button to tune to the station that

you want to store in memory.

Select any button, from [1] to [6], and press it for more than two

seconds.

The selected station is now stored in a preset button. Repeat the above procedure to store additional stations one at a time in buttons [1] to [6], and store them in memory.

CAUTION

If the vehicle's battery is disconnected (for repairs to the vehicle or for removing the main unit), all stations in memory will be lost. In such a case, store stations in memory again.

Preset station scan

VII

This function enables reception of all the stations

CAUTION

If the vehicle's battery is disconnected (for repairs to the vehicle or for removing the main unit), all stations in memory will be lost. In such a case, store stations in the memory again.

in the preset buttons for five seconds each.

Press the [SELECT] (Down) button

for more than one second.

"P SCAN" will appear on the display, and stations stored under preset buttons [1] through [6] will be played for five seconds each.

When your desired station is displayed, press the [SELECT]

(Down) button again.

The main unit will stay tuned to the desired station.

Page 44

Operation

Changing the reception sensitivity for automatic scanning

The main unit lets you select the reception sensitivity to be used for automatic scanning of stations. The two sensitivity modes available for this main unit are AUTO mode and DX mode.

During automatic scanning, the reception sensitivity switches automatically to one of two levels. Initially the reception sensitivity is

AUTO

Mode

DX Mode

When an optional HD Radio tuner unit is connected, reception sensitivity is set to the AUTO Mode. The DX Mode is unavailable. (U.S.A. only)

set to the low level so that only stations with strong signals are received. If no stations could be received, the reception sensitivity is increased so that stations with weaker signals can also be received.

Because the reception sensitivity for automatic scanning is set to the high level from the start, even stations with weaker signals can be received. (Signal crossover may result in some stations being hard to hear.)

ATTENTION

Changing the radio band location

The location for the radio bands used between the North American region and the Asia/ Australia/Latin region can be switched. The default setting is USA (North America).

ATTENTION

When an optional HD Radio tuner unit is connected, radio band location is set to USA. Other radio band locations are unavailable. (U.S.A. only)

Check that the main unit is in

standby.

Press and hold button [3] and the [ /MENU] button simultaneously

for more than three seconds.

The radio band switches in the order shown below each time the buttons are pressed.

USA → ASIA → AUS → LATIN → USA www

When the power is turned on, stations will be searched for automatically, and stored in buttons [1] to [6].

Check that the main unit is in

standby.

Press and hold button [1] and the [ /MENU] button simultaneously

for more than three seconds.

The mode switches between AUTO mode and DX mode each time the buttons are pressed.

Page 45

Page 46

Operation

How to use the remote control

Operation

Precautions in use of the remote control

• Be careful when handling the control, especially because it is small and light. Dropping or striking it

hard may damage it, wear out the battery or cause a malfunction.

• Keep the remote control free of moisture, dust and water. Do not subject it to shock.

• Do not place the remote control unit in places where it could be exposed to high temperatures, such

as on the dashboard or near a heater vent. Allowing the remote control unit to overheat may warp its case or cause other problems.

• Do not operate the remote control unit while driving because doing so could cause an accident.

• When using the remote control, point it toward the remote control light receptor.

• The light receptor may not operate correctly if it is exposed to bright light such as direct sunlight.

• Remove the batteries from the remote control unit whenever it is not to be used for a long time.

Cleaning the remote control

• Use a dry cloth to keep the remote control clean. If the remote control unit gets extremely dirty, clean

it with a cloth lightly moistened with diluted liquid detergent.

• In no event should alcohol, benzine or thinner be used. These substances will damage the case or

finish.

Remote control

(RMC-105)

No. Button Name/Working

[PWR] button

Turns main unit power ON/ OFF.

[TU] button

Switches to the tuner mode.

[BAND] button

Switches radio band.

[ , ] button

Decreases audio volume (including hands free mode).

[MUTE] button

Activates and deactivates mute.

Page 47

How to use the remote control

No. Button Name/Working

[ d PRESET CH u ] buttons [ dDISC u ] buttons

Selects radio preset channels and performs disc mode functions.

[MODE] button

Switches audio source mode.

[DISC] button

Switches to DISC mode (CD, CD changer, USB or iPod).

[AUX] button

Switches to AUX mode.

[ . ] button

Increases audio volume (including hands free mode)

[ d TUNE•SEEK u ]buttons [ > TRACK < ] buttons

Selects radio stations and CD tracks.

Replacing the battery

WARNING

To prevent accidents, store batteries out of the reach of children. If a child has swallowed one, consult a doctor immediately.

Use two AAA size batteries.

Insert the two batteries as indicated into the battery

compartment.

Slide the back cover in the direction indicated by the arrow to

close the battery case.

VIII

While pressing the back cover of the remote control unit, slide it in

the direction indicated by the arrow to remove it.

Page 48

Operation

The Bluetooth hands-free function

Operation

About the Bluetooth hands-free function

The use of Bluetooth wireless communication technology enables a Bluetooth-compatible cell phone to be able to be used with the main unit. Once the cell phone is connected to the main unit, it is possible to make calls without directly operating the cell phone. Because the connection between the cell phone and the main unit is wireless, communication is possible even when the cell phone is in your bag or pocket. Cable connection and wiring is not necessary.

• The main unit can be used with Bluetooth-

compatible cell phones.

• Before using a Bluetooth-compatible cell

phone with the main unit, please be sure to perform the Bluetooth registration and connection setting procedures. (For details, refer to "Registering a cell phone" on page 53 and "Connecting a registered cell phone" on page 54.)

• When the cell phone has been connected to

the main unit, the Bluetooth connection indicator and the radio wave status/phone connection status indicator appear on the displayed as shown below.

$NWGVQQVJ

EQPPGEVKQP

KPFKECVQT

4CFKQYCXGUVCVWURJQPG

EQPPGEVKQPUVCVWU

KPFKECVQT

• Depending on the surrounding environment, the connection may become unstable, and the Bluetooth hands-free function may not be able to be operated from the main unit. In such cases, confirm that the connection status is good be referring to the radio wave status indicator on the display, and then repeat the procedure.

• Some cell phones may not be compatible with the main unit.

ATTENTION

Using Bluetooth may cause batteries in connected devices to drain more quickly.

About the Bluetooth specifications

The Bluetooth-compatible cell phone to be connected to the main unit must be compatible with the following specifications. (However, depending on the model of the cell phone, some of the functions may be limited.)

Supported Bluetooth specifications

Bluetooth Specification Ver.2.0

Supported profile

• Once the cell phone has been connected to the main unit, it will remain connected until the connection is cancelled.

• Depending on the version of Bluetooth, some cell phones may not be able to communicate with the main unit.

• HFP (Hands Free Profile) Version 1.5: Profile for connection to Bluetoothcompatible hands-free devices

• OPP (Object Push Profile) Version 1.1: Profile for transmission of address book and schedule

Page 49

The Bluetooth hands-free function

What is Bluetooth?

Bluetooth is a form of short-range wireless communication technology used to connect cell phones and personal computers.

This technology enables hands-free calling and data transmission between Bluetooth-compatible devices.

ATTENTION

Please check with your cell phone manual for Bluetooth operation.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

WARNING

• For safety reasons, the driver must not operate the cell phone while driving.

• State and local ordinances must be strictly followed when using cell phones.

Selecting the Bluetooth handsfree mode

Press the [ /MENU] button

The Bluetooth hands-free mode is activated.

ATTENTION

• The Bluetooth hands-free mode can be activated from any audio mode.

• At any time the [RTN/BAND] button can be pressed to return to the previous step.

Making a call

This function enables you to dial phone numbers from the main unit, or to make calls using the stored phone numbers (phonebook) and incoming/outgoing call history.

Making a call by dialing a phone number

Calls can be made by dialing phone numbers from the main unit.

Before dialing a phone number directly from the main unit, set Dial Setting of the Phone Setting selection mode to ON. (For details, refer to "Enabling phone numbers to be input directly" on page 57.)

Press the [ /MENU] button

Press the [MODE] button repeatedly until the "Dial Input" is

displayed.

Press the [SELECT] (Up/Down) button to input numbers between 0

and 9.

Up:

Increases the number.

Down:

Decreases the number.

Press the [SELECT] (Right/Left)

button to move the cursor.

Right:

The cursor moves to the right.

Left:

The cursor moves to the left.

Repeat the Steps 3 and 4 to input

the phone number.

Page 50

Operation

ATTENTION

A maximum of 28 digits can be input per phone number. If you input an incorrect number, move the cursor to that number, and input the correct number by following Step 3.

Press the [ENTER] button when

you have input the phone number.

The input number confirmation screen appears on the display.

Press the [ENTER] button.

The input phone number is dialed.

Making a call using preset dial

Calls can be made using the phone numbers stored to the preset dial buttons.

Press the [ /MENU] button

Press a preset dial button between

[1] and [6].

The phone number and name stored in the selected preset dial button appear on the display, and the number is dialed (two beeps will be heard if no phone number is stored).

Making a call using the incoming/ outgoing call history

Calls can be made using phone numbers stored in the incoming/outgoing call history of the main unit.

Press the [MODE] button repeatedly until the "Incoming Calls" is displayed. (Incoming call

history) message appears on the display.

The incoming call history appears on the display. To make a call from the outgoing call history, press the [MODE] button repeatedly until the "Outgoing Calls" is displayed.

While in the call history selection mode, turn the [VOL] button to

select the number you want to call.

Press the [ENTER] button.

The phone number and name stored in the phonebook appear on the display to confirm the number to be dialed.

Press the [ENTER] button.

The phone number on the display is dialed.

ATTENTION

• A maximum of 10 outgoing and 10 incoming call records can be stored in one cell phone. If an attempt is made to store more than 10 call records, the oldest call record will be deleted.

• If the battery of the vehicle is disconnected, the call history stored in the main unit will be deleted.

Press the [ /MENU] button

Page 51

The Bluetooth hands-free function

Making a call using the phonebook

Calls can be made using the phone numbers stored in the phonebook of the main unit.

Press the [ /MENU] button

Press the [MODE] button repeatedly until the "Phonebook"

is displayed.

While in the phonebook selection mode, turn the [VOL] button to

select the number you want to call.

Press the [ENTER] button.

The phone number and name stored in the phonebook appear on the display to confirm the number to be dialed.

Press the [ENTER] button.

The phone number on the display is dialed.

Making a call from the cell phone

Calls can be made using a cell phone which is connected to the main unit.

Make a call using the cell phone.

ATTENTION

• If the phone number dialed from the cell phone has been stored in the phonebook of the main unit, the name and phone number will appear on the display.

• Depending on the cell phone, you may have to use the cell phone to talk even when the call has been made from the main unit.

Receiving a call

Calls can be received while in any source mode. There is also an automatic answering function to answer automatically. For details on answering calls automatically, refer to "Setting Auto Answer" on page 56.

When the phone rings, press the [ENTER] button or the [SELECT]

button.

A phone connection is made, and you can start talking.

Hanging up (refusing a call)

Calls can be terminated or refused.

Press the [ /MENU] button

The phone call is terminated.

ATTENTION

Calls which have been refused are also stored in the memory.

Adjusting the volume

The volume of the ring tone and the voice volume can be adjusted.

For safety reasons, do not adjust the volume of the ring tone or the voice volume while driving.

Adjusting the ring tone volume

Adjusting the volume of the ring tone while the phone is ringing.

Turn the [VOL] button to adjust the

volume.

To increase the ring tone volume:

Turn the [VOL] button to the right.

To decrease the ring tone volume:

Turn the [VOL] button to the left.

Page 52

Operation

Adjusting the voice volume

Adjust the voice volume while the call is in progress.

Turn the [VOL] button to adjust the

volume.

To increase the volume:

Turn the [VOL] button to the right.

To decrease the volume:

Turn the [VOL] button to the left.

Storing phone numbers in preset dial

It may be convenient for you to store phone numbers that you call regularly in preset dial. A maximum of 6 phone numbers from the call history or the phonebook can be stored in one cell phone’s preset dial.

Displaying the call history or the

phonebook.

(See page 50 to display call history). Select the phone number using the rotary dial. Press enter to confirm the phone number to be stored.

Press and hold the preset dial button between [1] and [6] that you

want to store a number in, until you hear a beep.

The displayed phone number from the call history or the phonebook is stored in preset dial.

Setting the Bluetooth hands-free function

A variety of settings that can be used when operating the cell phone can be made from the Bluetooth hands-free Phone Setting mode.

• Registration setting:

To register a cell phone.

• Select Phone setting:

To select a registered cell phone, and connect, disconnect, or delete it.

• Phone Book setting: To store data from the phonebook of the cell phone in the phonebook of the main unit.

• Auto Answer setting: To set the cell phone to Auto Answer.

• Ring tone setting: To set the ring tone.

• Auto Connect setting: To connect a registered cell phone.

• Device INFO display setting: To display device information for the main unit.

• Dial setting: To enable a phone number to be input using the main unit.

• Delete setting: To delete data from the incoming/outgoing call history, preset dial, or phonebook of the main unit.

• Change Code setting: To change the passcode.

Displaying the Phone Setting selection mode

Press the [ /MENU] button for

more than one second.

The MENU selection mode is displayed.

Press the [SELECT] (Up/Down)

button to select FUNC.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select Phone Setting.

Press the [ENTER] button.

Phone Setting selection mode is activated.

Page 53

The Bluetooth hands-free function

Registering a cell phone

Cell phones can be registered in the main unit. There are two methods that can be used to register a cell phone in the main unit.

The cell phone itself can be used or search for cell phones using the main unit. A maximum of five cell phones can be registered in the main unit. Priority of connection will always be in sequential order from 1 to 5. As cell phones are added and deleted, the order will always go by the numbered sequence.

Registering using a cell phone

If a cell phone is currently connected, it must be disconnected prior to registration of additional cell phones.

Press the [SELECT] (Up/Down) to select Registration within the

Phone Setting mode.

Press the [ENTER] button.

ATTENTION

NO ENTRY will be displayed if available. If not, a double beep will be heard if the phone registration memory is not available or full.

• Be sure to perform the registration of the

cell phone only while the "Waiting" message is on the display.

When the registration has been completed, the "COMPLETED"

message appears on the display.

The cell phone is now registered to the main unit

( and appear on the display.)

If the registration has not been successfully completed, the "FAILED" message appears on the display. Repeat the registration procedure.

ATTENTION

• To register another cell phone to the main

unit, press the [RTN/BAND] button twice after Step 6. Perform the registration procedure from the registered cell phone selection mode in Step 1.

• You cannot register a cell phone that has

already been registered.

• The hands-free function and the audio

function of the cell phone can be connected at the same time for some cell phones.

Press the [SELECT] (Up/Down)

button to select Allow Connect.

Press the [ENTER] button.

The "Waiting" message appears on the display.

Use the cell phone to input the

passcode.

The default passcode is 1234.

ATTENTION

• For details on how to operate the cell phone, read its instruction manual.

Searching for cell phones to be registered

Press the [SELECT] (Up/Down) to select Registration within the

Phone Setting mode.

Press the [ENTER] button.

ATTENTION

NO ENTRY will be displayed if available. If not, a double beep will be heard if the phone registration memory is not available or full.

Page 54

Operation

Press the [SELECT] (Up/Down)

button to select Device Search.

Press the [ENTER] button.

"Searching" will be displayed.

ATTENTION

"FAILED" will be displayed if cell phone cannot be registered. Repeat Search procedure.

Press the [SELECT] (Up/Down) button to select the device name of

the cell phone you want to register.

ATTENTION

Each time the [SCREEN/TEXT] button is pressed, the display changes in the following way, and you can register the cell phone using the device address (BD ADD) as well. Device name ↔ Device address (BD ADD) If the device name cannot be obtained during the search, "UNKNOWN" is displayed.

Press the [ENTER] button.

"Waiting" will be displayed.

Use the cell phone to input the

passcode.

The default passcode is 1234.

When the registration has been completed, "COMPLETED" will be

displayed.

The cell phone is now registered.

( and appear on the display.)

"FAILED" will be displayed if registration is not successful. Repeat Search procedure.

Delete a registered cell phone

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Select Phone.

Press the [ENTER] button.

Press the [SELECT] (Up/Down) button to select cell phone to be

deleted.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select Delete.

Press the [ENTER] button.

The "Delete ?" message appears on the display to confirm the cancellation.

Press the [ENTER] button.

"COMPLETED" will be displayed

when deletion is successful.

ATTENTION

When a cell phone is deleted, all data associated will also be deleted (including history, preset dial, and phonebook) from the main unit.

Connecting a registered cell phone

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Select Phone.

Press the [ENTER] button.

Page 55

The Bluetooth hands-free function

Press the [SELECT] (Up/Down) button to select the cell phone to

be connected.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select Connect.

Press the [ENTER] button.

The "Waiting" message appears on the display.

"COMPLETED" will be displayed.

The cell phone is now connected to the main unit.

( and appear on the display.)

"FAILED" will be displayed if registration is not successful. Repeat the connection procedure.

ATTENTION

Cell phones that have not been registered cannot be connected.

Disconnecting a cell phone

Press the [SELECT] (Up/Down)

button to select Disconnect.

Press the [ENTER] button.

The "Disconnect ?" message appears on the display to confirm the disconnection.

Press the [ENTER] button.

"COMPLETED" will be displayed

when disconnection is successful.

Registering phone number in the phonebook

Phone numbers can be registered in the phonebook of the main unit by transferring the phonebook data from the cell phone.

A maximum of 500 phone numbers can be registered for each cell phone.

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Phonebook.

Press the [ENTER] button.

The "DATA Receiving" message appears on the display.

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Select Phone.

Press the [ENTER] button.

Press the [SELECT] (Up/Down) button to select the cell phone to

be disconnected.

Press the [ENTER] button.

Transmit phonebook data using

your cell phone.

"COMPLETED" will be displayed

when data transfer is successful.

"FAILED" will be displayed if data transfer is not successful. Repeat the transmit procedure.

Page 56

Operation

ATTENTION

0WODGTQHRJQPGPWODGTUVJCVECP

DGTGIKUVGTGFKPVJGRJQPGDQQM

• If there is no space remaining in the main unit for phonebook data, the "MEMORY FULL" message appears on the display when an attempt is made to transfer data from the cell phone.

• Some cell phones cannot transfer all of the phonebook data at once. In this case, transfer one data at a time.

• If the battery terminal of the vehicle is disconnected, the phonebook data registered in the main unit will be deleted.

Setting Auto Answer

When there is an incoming call, the phone can be set to answer it automatically five seconds after the phone starts ringing.

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Auto Answer.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select ON or OFF.

ON:

Auto Answer is activated

OFF:

Auto Answer is disabled

ATTENTION

The default setting for Auto Answer is OFF (Auto Answer is disabled).

Setting the ring tone

The ring tone can be set on or off for incoming calls. Ring tone is set ON by default.

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Ring Tone .

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select ON or OFF.

Setting Auto Answer for registered cell phones

Cell phones which have been registered to the main unit will be connected automatically, if the main unit and the Bluetooth are in an area where connection is possible.

Auto answer is set ON by default and may not be available for all cell phones.

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Auto Connect.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select ON or OFF.

ON:

Connects automatically.

OFF:

Must be connected manually.

Page 57

The Bluetooth hands-free function

Displaying device information for the main unit

The name of the device (ECLIPSE BT), the passcode (default setting - 1234), and the BD ADD (device address) can be displayed.

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Device INFO.

Press the [ENTER] button.

The name of the device and Passcode will be displayed. Pressing the [SCREEN/TEXT] button will toggle between Passcode and BD ADD.

Enabling phone numbers to be input directly

The default setting is OFF.

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Dial Setting.

Press the [ENTER] button.

Deleting data from the phonebook

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Delete.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select Phonebook.

Press the [ENTER] button.

Press the [SELECT] (Up/Down) button to select ALL, a name, or a

phone number.

ALL:

Deletes entire phonebook.

Name or phone number:

Only the selected data is deleted.

Press the [ENTER] button.

If ALL is selected "DELETE?" and "ALL" will be displayed.

If a name or phone number is selected "DELETE?" and the name or phone number will be displayed.

Press the [SELECT] (Up/Down)

button to select ON or OFF.

Deleting data

Phonebook, Call History, Preset Dial, and All Data can be deleted.

ATTENTION

If there is no cell phone connected, the data in the phonebook cannot be deleted.

Press the [ENTER] button.

When the data in the phonebook has been deleted, "COMPLETED"

will be displayed.

Deleting call history

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Delete.

Press the [ENTER] button.

Page 58

Operation

Press the [SELECT] (Up/Down) button to select Outgoing Calls or

Incoming Calls.

Outgoing Calls:

Outgoing call history

Incoming Calls:

Incoming call history

Press the [ENTER] button.

If Outgoing Calls is selected "DELETE?" and "Outgoing Calls" will be displayed.

If Incoming Calls is selected "DELETE?" and "Incoming Calls" will be displayed.

Press the [ENTER] button.

When the data in the call history has been deleted, "COMPLETED"

will be displayed.

Deleting preset dial

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Delete.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select Preset Dial.

Press the [ENTER] button.

"DELETE?" and "Preset Dial" will be displayed.

Press the [ENTER] button.

When the data in preset dial has been deleted, "COMPLETED" will

be displayed.

Deleting all data

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Delete.

Press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select ALL.

Press the [ENTER] button.

"DELETE?" and "ALL" will be displayed.

Press the [ENTER] button.

When the data has been deleted,

"COMPLETED" will be displayed.

Changing the passcode

The passcode for the main unit can be changed. 4 to 8 digits must be used. The default setting is

1234.

Press the [SELECT] (Up/Down) button while in the Phone Setting

selection mode to select Change Code.

Press the [ENTER] button.

Passcode and "0 displayed.

Press the [SELECT] (Up/Down) button to input numbers between 0

and 9.

Up:

Increases the number.

Down:

Decreases the number.

*******

" will be

Page 59

Press the [SELECT] (Right/Left)

button to move the cursor.

Right:

The cursor moves to the right.

Left:

The cursor moves to the left.

Repeat Steps 3 and 4 to input the

passcode to enter the next digit.

Press the [ENTER] button when

you have input the passcode.

"NewPasscode?" will be displayed.

Press the [ENTER] button.

"COMPLETED" will be displayed.

The Bluetooth hands-free function

Page 60

Various Settings

ESN security operating procedure

Various Settings

About ESN

This main unit is equipped with ESN (ECLIPSE Security Network). A music CD (Key CD) which has been registered in the main unit, is necessary for ESN. Without it, none of the functions will operate, even when the battery is reconnected after it has been disconnected for maintenance, or the ignition switch is turned to ACC or ON after it has been turned to OFF. ESN can be set or cancelled using any of the following methods:

• Key CD security

You can register a music CD in the main unit as the “Key CD” to be used to set or cancel the security settings.

How to operate the ESN (Key CD) security

How to program the Key CD

Check that the power of the main

unit is in standby.

Press the [ e (OPEN/EJECT)]

button.

The front panel opens.

Insert the Key CD into the disc slot.

A "SEC" message appears, then the Key CD is ejected. The front panel will close automatically.

ATTENTION

• If there is a problem with the inserted CD, an "ERR" message will appear for two seconds and the CD will be ejected. Reinsert the ejected CD.

• If the "ERR" message appears on the display twice in a row, the "CHANGE" message will be displayed for two seconds. In this case, try another CD.

• Copy Protected CD and MP3/WMA CDROM cannot be programmed for Key CD security.

• The Security indicator will flash whenever the vehicle's ignition is switched off.

While pressing button [6], press the [SCREEN/TEXT] button, and

hold both for more than one second.

The "SEC" message appears on the display and changes to the "DISC" message after two seconds.

ATTENTION

• If a CD has already been inserted, a "SEC" message appears, and then the front panel opens and the CD is ejected.

• If a security is activated, programming the Key CD is not available.

How to cancel the Key CD

Check that the power of the main

unit is in standby.

While pressing button [6], press the [SCREEN/TEXT] button, and

hold both for more than one second.

The "SEC" message appears on the display and changes to the "DISC" message after two seconds.

Press the [ e (OPEN/EJECT)]

button.

The front panel opens.

Page 61

ESN security operating procedure

ATTENTION

If a CD has already been inserted, a "SEC" message appears, and then the front panel opens and the CD is ejected.

Insert the Key CD into the disc slot.

"CANCEL" will be displayed and the CD will be ejected. ESN is now deactivated.

ATTENTION

If a CD other than the Key CD is inserted, the registration cannot be cancelled. In this case, the "ERR" message is displayed for two seconds, and the CD playback mode is activated.

Press the [ e (OPEN/EJECT)]

button.

The front panel closes.

How to change the Key CD

First, cancel the existing Key CD.

Refer to "How to cancel the Key CD".

When the power is turned on after the battery power has been disconnected, the "SEC" message is displayed for two seconds. The

message then changes to the "DISC" message. Press the [e (OPEN/EJECT)] button.

Insert the Key CD into the disc slot.

"OK" will be displayed for two seconds and the CD will begin playing.

ATTENTION

• If the incorrect CD is inserted, an "ERR_ " (“ERR” and error number) message will appear for two seconds, after which the CD will be ejected.

• If the "ERR5" (the 5th time an error has occurred) message appears on the display, the "HELP" message will appear, and the CD will be ejected. When the "HELP" message appears, carry out the operations for ESN security lock out by following the procedure in "What happens if an incorrect CD is inserted?" on page 61.

• You must be use the same CD used for Key CD programming; a duplicate CD may not work properly.

Next, program a new Key CD.

Refer to "How to program the Key CD".

How to resume normal operation (ESN security lock out)

If power is disconnected while ESN security is active (a Key CD was programmed), operation is disabled until power is restored and the main unit unlocked. Follow this procedure to resume normal operation.

What happens if an incorrect CD is inserted?

After the 5th incorrect attempt, the "HELP" message will be displayed

for five seconds.

"HELP" will be displayed for 5 seconds. Then the serial number will be displayed.

Press the [e (OPEN/EJECT)]

button to close the front panel.

Page 62

Various Settings

While pressing button [6], press the [SCREEN/TEXT] button, and

hold both for five seconds.

"SEC" will be displayed for two seconds. Then the six digit rolling code will be displayed.

Press the [SCREEN/TEXT] button.

"DISC" flashes on the display.

You will have five more attempts to insert correct disc.

Insert the Key CD into the disc slot.

"OK" will be displayed for two seconds and then the CD will be ejected.

ATTENTION

• If an incorrect CD is inserted, an "ERR_ " (“ERR” and error number) message will appear for two seconds, after which the CD will be ejected.

• This process cancels the protection for ESN main unit.

NOTE

If after 5 tries the correct Key CD is not inserted, the display reads "CALL". Contact Eclipse for assistance.

It is easy to forget the name of your Key CD. Make a note of the album name to remind yourself (refer to page

110).

How to turn the security indicator on/off

Once ESN security is activated, the indicator flashes whenever the vehicle's ignition switch is turned off, warning potential thieves that the main unit is protected. However, if do not want this visible deterrent, it may be turned off.

With the main unit in standby, and while pressing button [2], press

the [SCREEN] button, and hold both for more than one second.

The "IND. FLASH" message or the "IND.-----" message appears on the

display.

"IND. FLASH" means the security indicator will flash when the vehicle's ignition switch is off, and "IND.-----" means it will not. Repeat the above steps to reactivate the flash mode.

How to read the Electronic Serial Number

Check that the power of the main

unit is in standby.

While pressing button [4], press the [SCREEN/TEXT] button, and

hold both for more than one second.

After the "ESN" message appears on the display, an 8 digit number will appear. This number is the Electronic Serial Number (ESN) of the device. You may use this number to identify your Eclipse CD3200 in the event of theft recovery.

Page 63

Page 64

Various Settings

How to operate the AUDIO CONTROL

Various Settings

Switching audio control modes

Various audio control modes may be fine-tuned using this procedure.

Press the [ENTER] button for less than one second to select the item to be

adjusted.

Modes will switch in the order shown below each time the button is pressed.

BASS → MID → TREB → BALANCE → FADER → NON-F → VOL → BASSwww

*1: NON-F (non-fader) Output is not affected by the settings of the BASS, MID and

TREB.

*2: Setting cannot be made in FM mode.

→ LOUDNESS → SVC

Mode Function

BASS Adjusts bass level. Decrease level. Increase level.

MID (MIDDLE)

TREB (TREBLE)

SVC (Source Volume Control)

FADER

BALANCE

NON-F (NON-FADER LEVEL)

LOUDNESS

Adjusts middle level. Decrease level. Increase level.

Adjusts treble level. Decrease level. Increase level.

Adjusts different volume levels for each audio mode.

Adjusts the audio balance of the front and rear speakers

Adjusts the audio balance of the right and left speakers

Adjusts non-fader level (for subwoofer).

The loudness control may be turned on to emphasize low and high frequencies at low volume levels. Loudness boosts bass and treble at low volumes.

Decrease level. Increase level.

Emphasizes rear speakers.

Emphasizes the left speakers.

Decrease the subwoofer level.

Select OFF Select ON

Rotary Mode

Left Right

Emphasizes front speakers.

Emphasizes the right speakers.

Increase the subwoofer level.

Page 65

How to operate the AUDIO CONTROL

SVC Setting examples:

The volume for the default FM mode (default value: 40) is used as a reference for storing the differences in volume that have been set for each audio mode.

Audio mode FM AM CD USB BT-Audio

Default value (Volume level)

SVC setting (Volume level)

When volume level in FM mode is adjusted from 40 to 45

When volume level in CD mode is adjusted from 35 to 60

When volume level in AM mode is adjusted from 80 to 20

When volume level in USB mode is adjusted from 10 to 35

*: The volume levels can only be set from 0 (min) to 80 (max). The volume difference can be set within a

range of -10 to +20.

Reference

(40)

Reference

(40)

45 55

→ 70 60 → 80* 60 50 → 75 40 → 65

→ 52060 → 0* 75 → 10 65 → 0

→ 30 20 → 45 0 → 20 35 0 → 25

(40)

SVC setting

value

-15 (55)

(40)

SVC setting

value

-10 (30)

(40)

SVC setting

value

+5 (45)

→ 60 30 → 35 45 → 50 35 → 40

SVC setting

(40)

value

-5 (35)

Page 66

Various Settings

How to operate the Sound Adjustment Mode

Various Settings

About Sound Adjustment Mode

The system has several features that allow you to adjust the acoustic characteristics inside the cabin.

Item Function Page

PEQ (Parametric EQ)

Position (Position selector)

X-Over (Cross over)

Non-F setting (Non-fader setting)

3-band setting, the frequency, and the Q curve pattern can be adjusted.

A preset speaker level for each seat, and the balance can be selected. 70

Specified frequency bands are allocated to each speaker for improved sound integration.

The sub-woofer phase can be switced. 71

Page 67

How to operate the Sound Adjustment Mode

About parametric EQ

A variety of materials are used inside a vehicle to manufacture the seats and windows, and because these materials absorb and reflect sound in different ways, the parametric equalizer lets you adjust the peaks and dips of the frequency characteristics inside the vehicle to compensate for this.

High

[Sound pressure]

Low

[Frequency]

An “equalizer” is a function that corrects these peaks and dips in order to flatten the frequency characteristics. However with a normal graphic equalizer, the median frequency and the Q (sharpness and band width) are fixed, so that when neighboring bands are corrected, there is a limit to the amount by which distortion in the peak and dip characteristics can be corrected. A “parametric equalizer” lets you adjust the median frequency, Q (sharpness and band width) and gain to variable levels, so that you can make fine adjustments to spot areas of the frequency band.

[Parametric equalizer characteristics]

1.Median frequency can be varied.

High

[Sound pressure]

Peak

Dip

High

Low

[Frequency]

High

2.Gain can be varied.

High

[Sound pressure]

Low

[Frequency]

High

3.Q (sharpness/band width) can be varied.

High

[Sound pressure]

Low

[Frequency]

High

About position selector

From the preset speaker level and Balance/Fader value, the position selector easily provides the listener optimum phase by selecting the seat position.

XII

Page 68

Various Settings

About crossover

The frequency band that is stored by audio media such as CDs is a fairly wide range from 20 Hz to 20 kHz, and it is difficult for a single speaker to be able to play back all frequencies in such a wide range.

Because of this, several speakers can be used, with different frequency bands (such as treble, medium and bass) allotted to each speaker so that wide frequency ranges can be played back. The “Crossover” function is used to allot the frequency ranges that are to be played back by each speaker in accordance to the installed speaker units and the layout of the speakers, in order to obtain the maximum level of performance from the speakers and to provide the most stable frequency characteristics.

The crossover function includes a high-pass filter (HPF) for playing back treble sounds, and a lowpass filter (LPF) for playing back bass sounds. In addition, the HPF and LPF are used in combination in order to play back sounds in the mid range.

-3dB

20Hz

Bass range (woofers)

fc (LPF) fc (HPF)

Medium range (front/rear speakers)

3dB

20kHz

For example, when adjusting the HPF, frequencies that are lower than the specified frequency are progressively dampened, rather than simply not being played back at all. The “slope” adjustment function is the function that is used to adjust these dampening characteristics.

The slope characteristics of a filter are such that with larger slope values (for example 12 dB/oct), the slope becomes steeper, and so the amount of sound mixing in with neighboring bands becomes less so that only the target band is played back. However, it also causes the merging of sound between speakers to become poorer and can result in greater distortion.

• The crossover function is a filter that allocates the specified frequency bands.

• A high-pass filter (HPF) is a filter that cuts out frequencies that are lower than the specified frequency (bass range) and allows higher frequencies (treble range) to pass through.

• A low-pass filter (LPF) is a filter that cuts out frequencies that are higher than the specified frequency (treble range) and allows lower frequencies (bass range) to pass through.

• The slope is the signal level at which frequencies that are one octave higher or one octave lower are dampened.

Page 69

How to operate the Sound Adjustment Mode

Switching the sound adjustment mode

Press the [ /MENU] button for

more than one second.

The Menu selection mode is activated.

Press the [SELECT] (Up/Down)

button to select SOUND.

Press the [ENTER] button.

The sound selection mode is activated.

Press the [SELECT] (Up/Down)

button to select a setting item.

Each time the button is pressed, the setting item changes.

PEQ ↔ Position Sel ↔ X-Over ↔ NonF Phase ↔ PEQ www

Press the [ENTER] button.

The adjustment mode is switched.

Parametric equalizer adjustment (PEQ)

Setting preset EQ

Press a button from [2] to [6] while

the PEQ setting mode is activated.

Pressing the button allows you to toggle through preset EQ modes as follows:

Button Mode Patterns

[2] DEFEAT No EQ adjustments

[3] POWER The pattern that

[4] SHARP The pattern that

[5] VOCAL The pattern that

[6] CUSTOM Custom pattern

emphasize the bass range.

emphasize the treble range.

emphasize the middle range.

ATTENTION

Custom EQ will be overwritten if the value for BASS, MIDDLE and TREBLE are adjusted in the audio control mode. (For details, Refer to "How to operate the AUDIO CONTROL" on page 64.)

XII

Press the [SELECT] (Up/Down)

button to select PEQ.

Press the [ENTER] button.

The PEQ setting mode is activated.

Adjusting the median frequency and the Q curve

Frequency level and Q curve for 3 bands (BASS, MIDDLE and TREBLE) can be adjusted separately. Q curve pattern can be chosen from Narrow, Normal, MidWide or Wide for BASS, Narrow or Normal for MIDDLE, and Normal for TREBLE.

Press the [ENTER] button to select

the band to be adjusted.

Each time the button is pressed, the band changes in the following order.

BASS →MIDDLE →TREBLE →www

Page 70

Various Settings

Press the [SELECT] (Up/Down) button to adjust the Q curve

pattern.

Each time the button is pressed, the Q curve pattern changes in the following order.

When BASS is selected:

WIDE ↔ MidWIDE ↔ NORMAL ↔ NARROW ↔ WIDE ↔ www

When MIDDLE is selected:

NORMAL ↔ NARROW ↔ NORMAL ↔

www

When TREBLE is selected:

NORMAL (Fixed)

Press the [SELECT] (Right/Left)

button to adjust the frequency.

Each time the button is pressed, the frequency changes in the following order.

When BASS is selected:

60Hz ↔ 80Hz ↔ 100Hz ↔ 120Hz ↔ 60Hz ↔ www

When MIDDLE is selected:

700Hz (fixed)

When TREBLE is selected:

7.5kHz ↔ 10kHz ↔ 12.5kHz ↔ 15kHz ↔ 7.5kHz ↔ www

Position selector

The sound field can be adjusted for the listener's seat position.

Press the [SELECT] (Up/Down)

button to select Position Sel.

Press the [ENTER] button.

The position selector setting mode is activated.

Press the [ENTER] or [SELECT] (Up/Down/Right/Left) button to

select the position you want.

When each button is pressed, the position is changed as follows.

ENTER:

OFF

Up:

FRONT

Down:

REAR

Right:

FRONT-RIGHT

Left:

FRONT-LEFT

Crossover adjustment (X-Over)

ATTENTION

• The median frequency and the Q curve you set are used for BASS, MIDDLE and TREBLE in the audio control mode. (For details, Refer to "How to operate the AUDIO CONTROL" on page 64.)

• When the median frequency and the Q curve are adjusted, CUSTOM EQ is also updated.

Specified frequency bands are allocated to each speaker for improved sound integration.

Press the [SELECT] (Up/Down)

button to select the X-Over.

Press the [ENTER] button.

The crossover setting mode is activated.

Page 71

Press the [ENTER] button to select

LPF or HPF.

Each time the button is pressed, the setting item changes in the following order.

LPF*1 ↔ HPF

*1: The cut-off frequency is 80Hz.

*2: The cut-off frequency is 100Hz.

Press the [SELECT] (Up/Down)

button to select Slope ON or OFF.

When it is ON, the slope is 12dB/oct.

Non-fader phase (Non-F Phase)

The merging of sound between the front and rear speakers and the woofer can be improved by selecting the phase. Switch the phase to a phase which lets the speakers combine without any disharmony.

Press the [SELECT] (Up/Down)

button to select Non-F Phase.

Press the [ENTER] button.

The mode will change to the non-fader phase mode.

How to operate the Sound Adjustment Mode

XII

Press the [SELECT] (Up/Down) button to select Normal or

Reverse.

Up:

Normal

Down:

Reverse

Page 72

Various Settings

Making changes with Display Adjustment Mode

Various Settings

This mode lets you adjust the display brightness, change the display type, etc.

Switching the Display Adjustment Mode

Press the [ /MENU] button for

more than one second.

The Menu selection mode is activated.

Press the [SELECT] (Up/Down)

button to select DISP.

Press the [ENTER] button.

The display adjustment mode is activated.

Press the [SELECT] (Up/Down)

button to select a setting item.

When the button is pressed, the setting item changes in the following order.

Bright ↔ Illumination ↔ DISP Type ↔ DISP Data ↔ Scroll Type↔ Bright ↔ www

Press the [ENTER] button.

Switches among the adjustment modes.

Switching the brightness (Bright)

Default setting is maximum brightness (5).

Press the [SELECT] (Up/Down)

button to select Bright.

Press the [SELECT] (Right/Left)

button to adjust the brightness.

Right:

Increases the brightness level.

Left:

Decreases the brightness level.

Press the [ENTER] button.

The selected settings will take effect.

Changing illumination color

You can change the button illumination color in the following way.

Press the [SELECT] (Up/Down)

button to select Illumination.

Press the [ENTER] button.

The illumination setting mode is activated.

Press the [SELECT] (Up/Down)

button.

Press the [SELECT] (Up/Down) button to set illumination color as follows:

Blue/Red ↔ Blue/Green ↔ Blue/Amber ↔ All Red ↔ All Green ↔ All Amber ↔ Blue/Red ↔ www

Press the [ENTER] button.

The selected settings will take effect.

Press the [ENTER] button.

The bright setting mode is activated.

Page 73

Making changes with Display Adjustment Mode

Changing display type (DISP Type)

The display type (Background or Sound meter) can be changed.

Press the [SELECT] (Up/Down)

button to select DISP Type.

Press the [ENTER] button.

The display type setting mode is activated.

Press the [SELECT] (Up/Down)

button to select a setting item.

When the button is pressed, the setting item changes in the following order.

Background ↔ Sound Meter ↔ Background ↔ www

Press the [ENTER] button.

Switches among the adjustments modes.

Changing Background (Background)

Press the [ENTER] button.

The selected settings will take effect.

Changing the sound meter (Sound Meter)

The sound meter type can be changed.

Press the [SELECT] (Up/Down)

button to select Sound Meter.

Press the [ENTER] button.

The sound meter type setting mode is activated.

Press the [SELECT] (Up/Down)

button to select a setting item.

Each time the button is pressed, the analyzer type changes in the following order.

Type 1 ↔ Type 2

Press the [ENTER] button.

The selected settings will take effect.

XIII

Press the [SELECT] (Up/Down)

button to select Background.

Press the [ENTER] button.

The background setting mode is activated.

Press the [SELECT] (Up/Down)

button to select a setting item.

When the button is pressed, the background changes in the following order.

Motion picture1 ↔ Motion picture2 ↔ Motion picture1 ↔www

Page 74

Various Settings

Importing display data (DISP Data)

Screens can be downloaded from the ECLIPSE website (E-iSERV) and used instead of the preset motion pictures. Download the data by following the instructions on the ECLIPSE website (E-iSERV). After you have downloaded the data onto your PC, copy it to a CD-R or a USB memory and import it into the main unit. (URL:http://www.e-iserv.jp) Applications for creating motion pictures can be downloaded, allowing you to create your own screen. Screens can be created by following the procedure shown below:

Select several pages of images to use in your picture.

↓

Access The ECLIPSE website. (URL: http://www.e-iserv.jp)

↓

Download ECLIPSE' s original image editing software (Cutting Board) following the instructions provided by the website.

↓

Using the image editing software (Cutting Board), adjust image size to fit the display. To edit images follow the instructions provided with the editing software.

↓

Convert your edited images into moving pictures following the instructions provided by the image editing software (Cutting Board).

↓

Copy the images to a CD-R or a USB memory.

↓

Import into the main unit.

Press the [SELECT] (Up/Down)

button to select DISP Data.

Press the [ENTER] button.

The display data import mode is activated.

Press the [SELECT] (Up/Down)

button to select the media type.

Press the [ENTER] button.

• When using a CD-R: "INSERT DISC" is displayed, and the front panel opens automatically. If a CD has already been loaded into the main unit, it will automatically eject.

• When using a USB memory: "CONNECT USB" is displayed until a USB memory is connected to the main unit. When a USB memory containing data has already been connected, the unit starts reading data immediately after pressing the [ENTER] button.

Insert the selected media.

Press the [e (OPEN/EJECT)]

button to close the front panel.

Press the [SELECT] (Up/Down)

button to select a file.

Press the [ENTER] button.

Press the [SELECT] (Up/Down) button to select the image data you

want to overwrite.

Press the [ENTER] button.

Start importing the data into the main unit. If the data has already been imported, it will be overwritten. When the data has been imported, the "Completed" message appears. The front panel will open automatically, and the CD-R will be ejected. Press the [ e (OPEN/EJECT)] button to close the front panel.

Page 75

Making changes with Display Adjustment Mode

CAUTION

On the CD-R or USB memory, if there is no file whose data type is the one you selected, the "NO DATA" message will be displayed and return to the previous screen.

ATTENTION

• When playing a music file in USB memory, E-iSERV data stored in the USB memory cannot be read into the main unit.

• To load data into the main unit, you have to make a special folder. For detailed information about how to make the folder, refer to the E-iSERV manuals.

CAUTION

• Do not turn the ignition switch or the power to the main unit ON or OFF (or remove the front panel of the main unit) while data reading is in progress. Data reading will be interrupted and data may be damaged.

• Only the [VOL] button can be operated while the system is reading data.

Changing the scroll type (Scroll Type)

The scroll type of the text display can be changed.

Press the [SELECT] (Up/Down)

button to select the Scroll Type.

Press the [ENTER] button.

The scroll type setting mode is activated.

Press the [SELECT] (Up/Down)

button to select the scroll type.

Each time the button is pressed, the scroll type changes in the following order.

Once ↔ Repeat

Once:

Scrolls the text once before changing to a fixed display.

Repeat:

Repeats scrolling the text.

The selected settings will take effect.

XIII

Page 76

Various Settings

Making changes with Function Mode

Various Settings

A variety of settings can be changed.

Switching the Function Mode

Press the [ /MENU] button for

more than one second.

The Menu selection mode is activated.

Press the [SELECT] (Up/Down) button to select FUNC, and then

press the [ENTER] button.

The function mode is activated.

Press the [SELECT] (Up/Down)

button to select a setting item.

When the button is pressed, the setting item changes in the following order.

STATION NAME*1 ↔ DISC TITLE*2 ↔ GUIDE TONE ↔ Clock ON/OFF ↔

Clock Adjust ↔ Demo ↔ HD RADIO ↔ AUX ON/ OFF*4 ↔ AUX Sens*4 ↔ Steering SW ↔ SIRIUS ID ↔ Phone Setting*7 ↔ BT Audio Set

*1: Cannot make settings other than

for tuner operation.

*2: Cannot make settings other than

for CD/CD changer operation.

*3: This setting can only be chosen

when an optional HD Radio tuner unit is connected. (Refer to page 86 for details on HD Radio operation.)

*4: Refer to page 101 for detail on

AUX operation.

*5: This setting can only be chosen

when an optional SIRIUS Satellite radio tuner unit is connected. (Refer to page 94 for details on SIRIUS Satellite radio operation.)

↔ XM ID

*6: This setting can only be chosen

when an optional XM Satellite radio tuner unit is connected. (Refer to page 90 for details on XM Satellite radio operation.)

*7: For details, refer to "Setting the

Bluetooth hands-free function" on page 52.

*8: For details, refer to "Bluetooth

audio setup" on page 38.

Setting a station name/disc title

The name of the station being received, or the title of the CD being played can be set.

ATTENTION

Not available with HD-Radio or SAT radio.

Press the [SELECT] (Up/Down) button to select Station Name or

Title.

Station Name or Title will be selected based on the current audio mode settings.

Press the [ENTER] button.

The title setting mode is activated.

Press the [SCREEN/TEXT] button

to select the character type.

Pressing the button will switch types from [ABC] (upper-case alphabet characters) to, [123] (numeric characters) and then [!“#] (symbols).

Page 77

Making changes with Function Mode

Press the [SELECT] (Right/Left) button to select the positions

where characters will be input.

The character will be inserted where the cursor is flashing.

Right:

Advances the cursor to the right.

Left:

Returns the cursor to the left.

Press the [SELECT] (Up/Down)

button to select characters.

Up:

Moves the character forward in its type.

Down:

Moves the character backward in its type.

[Symbol] First character [!] ! ↔ “ ↔ # ↔ $ ↔ % ↔ & ↔ ’↔ ( ↔ ) ↔ * ↔ + ↔ , ↔ - ↔ . ↔ / ↔ : ↔ ; ↔ < ↔ = ↔ > ↔ ? ↔ @ ↔ ' ↔ _ ↔ ! ↔ www

[Upper-case alphabet characters] Initial value [A] A ↔ B ↔ C ↔ www ↔ X ↔ Y ↔ Z ↔ A ↔ www

[Numeric characters] Initial value [1] 1 ↔ 2 ↔ 3 ↔ www ↔ 8 ↔ 9 ↔ 0 ↔ 1 ↔ www

Press the [ENTER] button to save

the title.

ATTENTION

• To change the type of character to be entered, repeat steps 3 and 5.

• A maximum of 16 characters may be entered per title.

• 30 titles can be stored.

• When the data storage area is full, the "FULL DATA" message appears. If new data is input, the older data will be deleted.

Deleting a station name/disc title

Press the [RTN/BAND] button for more than two seconds while the

title setting mode is activated.

The station name/disc title that is displayed at this point will be deleted.

Setting the guide tone

The main unit is set at the factory to emit a beep tone in response to button operation. The guide tone feature may be disabled in the following procedure:

Press the [SELECT] (Up/Down)

button to select Guide Tone.

Press the [ENTER] button.

The guide tone setting mode is activated.

Press the [SELECT] (Up/Down) button to select Guide Tone ON/

OFF.

Setting clock display (Clock ON/ OFF)

Switches the clock display to ON/OFF.

Press the [SELECT] (Up/Down)

button to select Clock ON/OFF.

Press the [ENTER] button.

The clock display setting mode is activated.

XIV

Page 78

Various Settings

Press the [SELECT] (Up/Down) button to set the clock display to

ON or OFF.

ATTENTION

The clock display can also be turned on and off by pressing the button [6] while the power is turned off.

Setting time (Clock Adjust)

This main unit uses the 12-hour display notation.

Press the [SELECT] (Up/Down)

button to select Clock Adjust.

Press the [ENTER] button.

The clock setting mode is activated.

Press the [SELECT] (Right/Left) button to select the item to be

adjusted.

Right:

Minutes will be switched.

Left:

Hours will be switched.

Switching demonstration screen display (Demo)

Demonstration screen display settings can be performed. Default setting is ON.

If the demonstration screen display is set to ON, operation, motion picture, and other screens will be displayed in succession.

If you press a button while the demonstration screens are being displayed, the demonstration screens will be cancelled and the audio operation screen will be displayed. If you do not operate the status display function within 15 seconds, the display will return automatically to the demo screen.

Press the [SELECT] (Up/Down)

button to select Demo.

Press the [ENTER] button.

The demo display setting mode is activated.

Press the [SELECT] (Up/Down)

button to select Demo ON/OFF.

Press the [SELECT] (Up/Down)

button to adjust the time.

Up:

Turns the time forward.

Down:

Turns the time back.

Press the [ENTER] button.

Page 79

Making changes with Function Mode

Setting the steering remote function (U.S.A. only)

The vehicle’s factory loaded steering remote becomes inoperable when the CD3200 is installed. The ECLIPSE website (E-iSERV) provides software that enables steering remote operation even with the installation of the main unit. Import this software into your CD3200.

For details, contact the store from which you purchased your main unit. Depending on your vehicle’s make and model, material downloaded from the website may not be compatible with your steering remote. Consult the store from which you purchased your CD3200 about compatibility and set-up procedures. Software for the steering remote can be downloaded and imported into the main unit as follows:

Access The ECLIPSE website. (URL: http://www.e-iserv.jp)

↓

Download the steering remote software following instructions provided on the ECLIPSE website (E-iSERV). (Because material available on the website may not be compatible with the steering remotes found on some automobiles, make sure to check the website for details about compatibility.)

↓

Copy the downloaded software to CD-R or a USB memory.

↓

Import into the main unit.

↓

The steering remote can be operated.

Reading steering remote data (U.S.A. only)

The steering remote data that has been downloaded from E-iSERV (website) to a USB memory or CD-R can be loaded into the main unit and save there.

Press the [SELECT] (Up/Down)

button to select Steering SW.

Press the [ENTER] button.

The steering remote setting mode is activated.

Press the [SELECT] (Up/Down)

button to select the media type.

Press the [ENTER] button.

When using a CD-R:

“INSERT DISC” will be displayed and the front panel will open automatically.

When a USB memory is used:

The "CONNECT USB" message will be displayed until the USB memory is connected.

Insert the CD-R or connect the USB memory to save the steering

remote data.

Press the [e (OPEN/EJECT)]

button to close the front panel.

Press the [SELECT] (Up/Down)

button to select a file.

XIV

Page 80

Various Settings

Press the [ENTER] button.

The CD-R or USB memory data is read. While it is reading, "READING" is displayed.

If the data can be read successfully, "COMPLETED" will appear on the display. When using CD-R data, the CD-R will automatically eject when reading is complete.

ATTENTION

• To load data into the main unit, you have to make a special folder. For detail information about how to make the folder, refer to the EiSERV website.

• This function is available only for vehicles equipped with steering remote with an interface that operates by detecting voltage

• When playing a music file in USB memory, E-iSERV data stored in the USB memory cannot be read into the main unit.

CAUTION

• Do not turn the ignition switch or power to the main unit ON or OFF (or remove the front panel of the main unit) while data reading is in progress. Data reading will be interrupted and data may be damaged.

• Only the [VOL] button can be operated while the system is reading data.

Page 81

Making changes with Function Mode

Compatibility with various switches

The compatibility of the main unit's various modes and the steering remotes installed on your vehicle are as follows:

Switch

Name

TRACK+

TRACK-

VOL+

VOL-

MODE

MUTE

POWER

Button

function

Press

briefly

Press and

hold

Press briefly

Press and

hold

Press briefly

Press and

hold

Press briefly

Press and

hold

Press briefly

Press and

hold

Press briefly

Press and

hold

Press briefly

Press and

hold

Mode

Tuner

TUNE UP

SEEK

TUNE

DOWN

SEEK

DOWN

Increases

the volume

Gradually increases

volume

Decreases the volume

Gradually

decreases

volume

Switches

to the next

mode

MUTE MUTE MUTE MUTE — MUTE —

Power

OFF

Disc/USB

mode

TRACK

FAST UP — FAST UP — FAST UP —

TRACK

DOWN

FAST

DOWN

Increases

the volume

Gradually increases

volume

Decreases the volume

Gradually

decreases

volume

Switches

to the next

mode

———————

Power

OFF

———————

AUX iPod

—

Increases

the volume

Gradually increases

volume

Decreases the volume

Gradually

decreases

volume

Switches

to the next

mode

Power

OFF

TRACK

DOWN

FAST

DOWN

Increases

the volume

Gradually increases

volume

Decreases the volume

Gradually

decreases

volume

Switches

to the next

mode

Power

OFF

Power

OFF

—

Power ON

in the last

mode

Power ON

in the last

mode

BT-Audio

mode

TRACK

DOWN

FAST

DOWN

Increases

the volume

Gradually increases

the volume

Decreases the volume

Gradually

decreases

the volume

Switches

to the next

mode

Power

OFF

BT-TEL

mode

—

Increases

the

volume

(ring tone/

speakers'

voices)

Increases

the

volume

gradually

(ring tone/

speakers'

voices)

Decreases

the

volume

(ring tone/

speakers'

voices)

Decreases

the

volume

gradually

(ring tone/

speakers'

voices)

Switches

to the next

mode

Power

OFF

XIV

Page 82

Various Settings

Switch

Name

ON HOOK

OFF HOOK

*1: Switch names change depending on vehicle make and model. *2: If a SIRIUS/XM satellite radio tuner (purchased separately) is connected, categories can be switched when in the satellite mode.

Button

function

Press briefly

Press and

hold

Press briefly

Press and

hold

Tuner

The TEL

mode is

activated.

Disc/USB

mode

— — — — — — ON HOOK

———————

The TEL

mode is

activated.

———————

AUX iPod

The TEL

mode is

activated.

Mode

The TEL

mode is

activated.

Power

OFF

The TEL

mode is

activated.

BT-Audio

mode

The TEL

mode is

activated.

BT-TEL

mode

OFF

HOOK

Page 83

Page 84

About the optional unit

How to operate the main unit with an optional CD changer connected

About the optional unit

This section covers the operation of an optional CD changer that is connected to the main unit.

Listening to a CD

Switch to CD changer mode.

For details, refer to "Switching Audio Modes" on page 18.

Advancing to the next track or returning to the beginning of the track being played

Press the [SELECT] (Right/Left)

button for less than one second.

Right:

Advances to the next track.

Left:

Returns to the beginning of the track being played. (Repeat pressing for previous tracks.)

Operations during rotary mode

Turn the [VOL] button.

Turn to the right:

Advances to the next track.

Turn to the left:

Return to the beginning of the track being played. Repeat turning for previous tracks.

Fast Forward/Rewind

Fast forward or rewind the song currently being played.

Press and hold the [SELECT]

(Right/Left) button.

Right:

Fast forward.

Left:

Rewind.

Playing the beginning of tracks (SCAN)

Press the [4 SCAN] button.

Pressing the button for less than one second causes the changer to move up to the next track and play it for 10 seconds, then move up to the next track and play it for 10 seconds, and so on, on one CD, until the button is pressed again.

Press the button for longer than a second to play the first 10 seconds of the first track of every CD loaded.

ATTENTION

• To continue playing a desired track, press the button again to stop scanning.

• After the entire disc is scanned once, ordinary playback starts from the point where scanning started.

Page 85

How to operate the main unit with an optional CD changer connected

Repeating the same track (REPEAT)

Press the [5 RPT] button.

Pressing on the button for less than one second causes the changer to repeat the track currently being played, until the button is pressed again. Press the button for longer than a second to repeat all tracks on the CD being played.

Press the button for more than one second to repeat all the tracks on the CD being played.

Playing tracks in random order (RANDOM)

Press the [6 RAND] button.

Pressing on the button for less than one second causes the changer to play the tracks on the currently playing CD in random order, until the button is pressed again.

Press the button for longer than a second to play tracks from all of CDs loaded in the currently selected changer, in random order. Tracks can be repeated during random play. This is not an abnormal occurrence.

ATTENTION

• During random playback, press the [5 RPT] button to repeat the track being played. To cancel the repeat play (and return to random play), press the [5 RPT] button again.

• When any of the functions - "Playing the beginning of tracks", "Repeating the same track" or "Playing tracks in random order" is selected, a message such as "SCAN", "ALL SCAN", "REPEAT", "ALL REPEAT", "RANDOM" or "ALL RANDOM" will appear on the display to verify the current function.

• Random play is not cancelled even if a magazine is ejected.

Skipping to the next or previous CD

Press the [SELECT] (Up/Down)

button.

Up:

Selects the next higher number disc.

Down:

Selects the next lower number disc.

Specifying a CD to play

A CD of your choice is directly selectable out of the loaded discs.

Press the [MODE] button for more

than one second.

Press a button from [1] to [6].

Buttons 1 2 3 4 5 6

CD 123456

789101112

To select a CD from nos. 7 to 12, press the desired button considerably longer.

Press the [MODE] button for more than one second to exit the direct

selection mode.

Page 86

About the optional unit

How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only)

About the optional unit

About HD Radio

If the optional HD Radio tuner unit is connected, terrestrial digital broadcasts can be received. When terrestrial digital broadcasts are received, the FM reception has the same sound quality as a CD, and the AM reception has the same sound quality as conventional FM sound. Depending on the reception status, HD Radio may also be able to receive analog broadcasts, which means reception is still possible in regions with no digital coverage.

See "How to operate the tuner" on page 42 for information on the following operations:

• Listening to the tuner

• Tuning to a station

• Entering stations into memory automatically (The automatic preset mode: ASM)

• Manually setting stations into memory

• Preset station scan

During digital broadcast reception, the "DIGITAL" message appears on the display.

Switching between displays when receiving HD Radio

During digital reception, the name of the station being received and other information can be displayed.

Press the [SCREEN/TEXT] button

for more than one second.

Each press will switch the display items in the following sequence: station name → title* → artist* → album* → genre.

*: Depending on the nature of the broadcast, no information may be shown.

HD Radio reception settings

The HD Radio reception method can be selected. When the HD Radio tuner is connected to this main unit for the first time, it will be set at [AUTO] (automatic digital/analog selection).

Press the [ /MENU] button for

more than one second.

The Menu selection mode is activated.

Press the [SELECT] (Up/Down) button to select FUNC, and then

press the [ENTER] button.

The function mode is activated.

Press the [SELECT] (Up/Down)

button to select HD Radio.

Press the [ENTER] button.

The reception setting screen is displayed.

Page 87

How to operate the tuner with an optional HD Radio tuner connected (U.S.A. only)

Press the [SELECT] (Up/Down)

button to select Auto or OFF.

In the [Auto] setting, the selection is switched between digital and analog reception automatically. In areas where digital reception is not possible, reception is automatically switched to analog to avoid loss of reception. While receiving the digital broadcast, the "DIGITAL" message appears on the display. This is cleared during analog reception.

In the [OFF] setting, reception is always analog.

XVI

Page 88

About the optional unit

How to operate the tuner with an optional XM satellite radio tuner connected (U.S.A./CANADA only)

About the optional unit

About XM satellite radio

Selecting a channel

If the optional XM satellite radio tuner unit is connected, satellite radio broadcasts can be received.

With XM satellite radio, over 170 channels are available including music, sports, news, and entertainment programs.

The channel can be selected from categories such as ROCK and DANCE, or by selecting individual channels manually.

Reception of XM satellite radio is fee based; you have to subscribe to it.

It is possible to subscribe through the XM radio website.

URL: http://www.xmradio.com

ATTENTION

• For details on the settings and operation of

the XM satellite radio tuner unit, refer to the XM satellite radio unit owner's manual.

• The main unit will accept up to 24 stations

in memory.

Selecting the radio mode

Switch to the XM satellite radio

mode.

For details, refer to "Switching Audio Modes" on page 18.

Press the [RTN] button for less than one second to switch to the

desired XM band.

The radio bands will switch from XM1

XM2 → XM3 → XM4 in order each

→ time the button is pressed.

Press the [SELECT] (Right/Left)

button to tune to a channel.

Right:

Selects a higher channel.

Left:

Selects a lower channel.

Press the [SELECT] (Right/Left) button for more than one second

to start an automatic channel search.

Reception is enabled for all channels within the currently selected category.

(Refer to page 89 for details on “Category selection”.)

Right:

Starts searching for higher channels.

Left:

Starts searching for lower channels.

Page 89

How to operate the tuner with an optional XM satellite radio tuner connected (U.S.A./CANADA only)

Operations during rotary mode

Turn the [VOL] button to the left or

right.

Turn to the right:

Tunes to higher channels.

Turn to the left:

Tunes to lower channels.

Category selection

The channel can be selected from among categories such as ROCK and DANCE.

Consult the XM website for the details of the categories.

Press the [SELECT] (Up/Down)

button for less than one second.

The category will switch in the order shown below each time button is pressed.

Up:

Advances to the next category.

Down:

Returns to the previous category.

Direct channel selection

The channel can be selected by inputting the channel directly.

Press the [MODE] button for more

than one second.

The mode will change to the direct channel selection mode.

Press the [SELECT] (Right/Left) button to select the channel

number.

Right:

Advances to the next number.

Left:

Returns to the previous number.

Press the [SELECT] (Up/Down) button to select the channel

number to be input.

Each time the button is pressed, the channel number changes in the following order.

0 ↔ 1 ↔ 2 ↔ 3 ↔ 4 ↔ 5 ↔ 6 ↔ 7 ↔ 8 ↔ 9 ↔ 0 ↔ www

Press the [ENTER] button.

Reception starts.

Manually setting channels into memory

This section covers the storing of stations in the memory of numbered buttons.

Press the [SELECT] (Right/Left) button to tune to the channel to be

stored in the memory.

Select any button, from [1] to [6], and press it for more than two

seconds.

The tuned channel is now memorized and set in the button selected. Repeat the procedure to set additional manually tuned channels into memory, in turn, for buttons [1] to [6]. These buttons are called the preset buttons.

ATTENTION

If the vehicle’s battery is disconnected (for repairs to the vehicle or when removing the main unit), all channels stored in memory will be lost. In such cases, set the channels into memory again.

XVII

Page 90

About the optional unit

Preset channel scan

This function enables the reception of all the channels in the preset buttons for five seconds each.

Press the [SELECT] (Down) button

for more than one second.

[P SCAN] will appear on the display, and channels set in preset buttons [1] through [6] will be received for five seconds each.

To stop the preset scan mode at the desired channel, press the

[SELECT] (Down) button again.

The main unit will stay tuned to the desired channel.

Switching displays when using the XM satellite radio

Press the [SCREEN/TEXT] button

for more than one second.

Each time the button is pressed the display item changes in the following order: channel name title → name → channel name → www

→ category name →

Displaying the XM ID

Displays the XM ID. The XM ID is necessary when subscribing to programs, etc.

Press the [ /MENU] button for

more than one second.

The Menu selection mode is activated.

Press the [SELECT] (Up/Down) button to select FUNC, and then

press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select XM ID.

Press the [ENTER] button.

The XM ID is displayed.

ATTENTION

If there are no names, the "NO DATA" message will appear.

Page 91

Page 92

About the optional unit

How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A./CANADA only)

About the optional unit

About SIRIUS satellite radio

Selecting a channel

If the optional SIRIUS satellite radio tuner unit is connected, satellite radio broadcasts can be received.

With SIRIUS satellite radio, over 130 channels are available, including music, sports, news, and entertainment programs.

The channel can be selected from categories such as POP and ROCK, or by selecting individual channels manually.

Reception of SIRIUS satellite radio is fee based; you have to subscribe to it.

It is possible to subscribe through the SIRIUS radio website.

URL: http://www.sirius.com

ATTENTION

• For information about the operation and

set-up of the SIRIUS satellite radio tuner unit, see the SIRIUS satellite radio unit's owner's manual.

• The main unit will accept up to 24 stations

in memory.

Selecting the radio mode

Switch to the SIRIUS satellite radio

mode.

For details, refer to "Switching Audio Modes" on page 18.

Press the [RTN] button for less than one second to switch to the

desired SR band.

Each time the button is pressed, the radio band changes in the order SIRIUS1 → SIRIUS2 → SIRIUS3 → SIRIUS4.

Press the [SELECT] (Right/Left)

button to tune to a channel.

Right:

Selects a higher channel.

Left:

Selects a lower channel.

Press the [SELECT] (Right/Left) button for more than one second

to start an automatic channel search.

Reception is enabled for all channels within the currently selected category. (Refer to page 93 for details on “Category selection”.)

Right:

Starts searching for higher channels.

Left:

Starts searching for lower channels.

Operations during rotary mode

Turn the [VOL] button to the left or

right.

Turn to the right:

Tunes to higher channels.

Turn to the left:

Tunes to lower channels.

Page 93

How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A./CANADA only)

Category selection

The channel can be selected from among categories such as POP and ROCK.

Consult the SIRIUS website for the details of the categories.

Press the [SELECT] (Up/Down)

button for less than one second.

The category will switch in the order shown below each time button is pressed.

Up:

Advances to the next category.

Down:

Returns to the previous category.

Direct channel selection

The channel can be selected by inputting the channel directly.

Press the [MODE] button for more

than one second.

The mode will change to the direct channel selection mode.

Press the [SELECT] (Right/Left) button to select the channel

number.

Right:

Advances to the next number.

Left:

Returns to the previous number.

Press the [SELECT] (Up/Down) button to select the channel

number to be input.

Each time the button is pressed, the channel number changes in the following order.

0 ↔ 1 ↔ 2 ↔ 3 ↔ 4 ↔ 5 ↔ 6 ↔ 7 ↔ 8 ↔ 9 ↔ 0 ↔ www

Press the [ENTER] button.

Reception starts.

Manually storing channels into memory

This section covers the storing of stations in the memory of numbered buttons.

Press the [SELECT] (Right/Left) button to tune to the channel to be

stored in the memory.

Select any button, from [1] to [6], and press it for more than two

seconds.

The tuned channel is now memorized and stored in the button selected. Repeat the procedure to stored additional manually tuned channels into memory, in turn, for buttons [1] to [6]. These buttons are called the preset buttons.

ATTENTION

If the vehicle’s battery is disconnected (for repairs to the vehicle or when removing the main unit), all channels stored in memory will be lost. In such cases, store the channels in memory again.

Preset channel scan

This function enables the reception of all the channels in the preset buttons for five seconds each.

Press the [SELECT] (Down) button

for more than one second.

[P SCAN] will appear on the display, and channels stored in preset buttons [1] through [6] will be received for five seconds each.

XVIII

Page 94

About the optional unit

To stop the preset scan mode at the desired channel, press the

[SELECT] (Down) button again.

The main unit will stay tuned to the desired channel.

Switching displays when using the SIRIUS satellite radio

Press the [SCREEN/TEXT] button

for more than one second.

Each time the button is pressed the display item changes in the following order:

channel name → category name → title → artist → channel name → www

ATTENTION

If there are no names, the "NO DATA" message will appear.

Displaying the SIRIUS ID

Displays the SIRIUS ID. The SIRIUS ID is necessary when subscribing to programs, etc.

Press the [ /MENU] button for

more than one second.

The Menu selection mode is activated.

Press the [SELECT] (Up/Down) button to select FUNC, and then

press the [ENTER] button.

Press the [SELECT] (Up/Down)

button to select SIRIUS ID.

Press the [ENTER] button.

The SIRIUS ID is displayed.

Page 95

Page 96

About the optional unit

How to operate the main unit with an optional Interface Adapter for iPod connected

About the optional unit

An iPod can be connected to the main unit using the optional Interface Adapter for iPod (iPC-106), allowing you to listen to iPod music files and operate some iPod functions from the main unit. For details on connecting the Interface Adapter for iPod, as well as settings and other information, refer to the OWNER’S MANUAL of the Interface Adapter for iPod.

iPod is for legal or right holder-authorized copying only. Don't steal music. iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.

Listening to iPod music files (If an iPod is not connected)

Connect the iPod using the

optional Interface Adapter for iPod.

The iPod will begin playing once it is connected.

ATTENTION

• The iPod will begin playing the music file it

was playing before being connected. If the main unit cannot detect the music file that was playing previously, it will begin playing from the first music file.

• When the iPod is connected using the

optional iPod Interface Adapter, the "ECLIPSE" message will be displayed on the iPod. While the "ECLIPSE" message is displayed, the iPod cannot be operated directly.

CAUTION

• Disconnect headphones and all other accessories from the iPod before connecting it to the optional Interface Adapter for iPod. Failure to do so may make it impossible to operate the iPod from the main unit.

• If the iPod's equalizer has been customized, the sound output may be distorted when it is connected to the optional Interface Adapter for iPod.

Listening to iPod music files (If an iPod is connected)

Switch to the iPod mode.

For details, refer to "Switching Audio Modes" on page 18.

Advancing to the next music file or returning to the beginning of the music file being played

Press the [SELECT] (Right/Left)

button for less than one second.

Right :

Advances to the next music file.

Left :

Returns to the beginning of the music file being played. (Repeat pressing for previous music files.)

Fast forward/rewind

Press and hold the [SELECT]

(Right/Left) button.

Right :

Fast forwards.

Left :

Rewinds.

Page 97

How to operate the main unit with an optional Interface Adapter for iPod connected

Searching for a music file

The iPod search mode can be operated from the main unit.

Press the [MODE] button.

The search mode is activated.

Turn the [VOL] button to select the

search mode item.

Search mode items are selected in the following order.

Playlists ↔ Albums ↔ Artists ↔ Genres ↔ Songs ↔ Playlists

Press the [ENTER] button.

The following information is displayed according to the selected search mode item.

Playlists:

The playlist selected on the iPod is displayed

Artists:

Artist names are displayed

Albums:

Album names are displayed

Songs:

Music file names are displayed

Genres:

Genre names are displayed

Turn the [VOL] button to select the desired search mode item, and

then press the [ENTER] button.

If SONGS is selected, the selected song will be played. If another search mode item is selected, continue the selection process until you have selected a song. All files in the selected list (playlist, artist, album or genres) will be played back and repeated. After selecting the desired search mode item (ARTIST, ALBUM or GENRES), press button [1] to play back all files in that item. No files can be played back even if button [1] is pressed after selecting PLAY LIST.

Press the [SELECT] (Up/Down)

button.

(Up):

10 tracks backward

(Down):

10 tracks forward

ATTENTION

• Each search item mode will display information in the following order before displaying music file information.

Search mode Display order

Playlists:

Artists: Artists → Albums → Songs

Albums:

Genres:

Songs: Songs

• The ALL option on iPod is displayed in the Playlists search mode. Select Playlists to play back all files.

Playlists → Songs

Albums → Songs

Genres → Artists → Albums → Songs

XIX

Page 98

About the optional unit

Repeating the same music file (REPEAT)

Press button [5].

Pressing this button causes the iPod to repeat the music file currently being played, until the button is pressed again.

Playing music files in random order (SHUFFLE)

Press button [6].

Pressing this button for more than one second causes the iPod to play the music files on the album currently being played in random order, until the button is pressed again.

Press the button for less than one second to play all the iPod music files currently being played in random order.

Displaying text

The display can be switched to show the album name, the artist name and the song name.

Press the [SCREEN/TEXT] button

for more than one second.

The album name, the artist name and the song name are scrolled and displaying, the information is displayed in the following order.

Song → Artist → Album → Songwww

ATTENTION

• Text recorded with characters other than alphanumeric characters and symbols cannot be displayed.

• Characters that cannot be displayed are displayed as * (asterisks).

• If there is no text stored in a music file, the "NO DATA" message will appear.

ATTENTION

• When either of the functions- REPEAT or RANDOM is selected, a message such as "RPT", "ALL-RAND" or "RAND" appears on the display to verify the current function.

• REPEAT and RANDOM both operate in the same manner as the REPEAT and SHUFFLE modes on iPod.

Page 99

Page 100

About the optional unit

Others

About the optional unit

Connecting a portable audio player to the AUX jack

Use a commonly available accessory cable with an RCA connector or an optional AUX105 to connect a portable audio player to the AUX (auxiliary) jack of this system.

There are 2 connection terminals on this main unit; one for the RCA connector and the other for the optional LAN cable (AUX 105). The default setting for AUX is OFF.

Turn on the portable audio player

and start its play function.

The AUX mode is activated.

For details, refer to "Switching Audio Modes" on page 18.

ATTENTION

• While the AUX mode is activated, actions such as turning off the audio player or pulling out the connection cord may cause noise spikes that can damage the system speakers. Be sure to avoid this possibility by turning off system power or switching from the AUX mode to another mode before shutting off or disconnecting the portable audio player.

• Audio output levels for the various devices that can be connected using this method will differ. Carefully adjust the volume until the output level of the connected player is known.

• Before using a portable audio player in a vehicle, read the player's operation manual carefully and confirm problem-free operation in the vehicle before proceeding.

• When you connect an optional LAN cable (AUX 105) to the main unit, other optional equipment that uses E-LAN cannot be connected.

Switching the AUX mode on and off

Press the [ /MENU] button for

more than one second.

The Menu selection mode is activated.

Press the [SELECT] (Up/Down) button to select FUNC, and then

press the [ENTER] button.

The function mode is activated.

Press the [SELECT] (Up/Down)

button to select AUX ON/OFF.

The AUX ON/OFF mode is activated.

Press the [SELECT] (Up/Down)

button to select the ON/OFF mode.

Press the button to switch the mode as follows:

Up:

Mode is ON

Down:

Mode is OFF

The selected settings will take effect.

Switching the input system

When using an optional AUX cord (AUX105), the main unit can be switched between RCA input and optional AUX cord (AUX105) input.

Press the [MODE] button for more

than one second.

The system will switch between RCA input and optional AUX cord input each time the button is pressed.

RCA input (INPUT) ↔ Optional AUX cord (SUB INPUT)

100

Eclipse - Fujitsu Ten CD3200 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

For your safety in using the CD3200

Operating precautions

Notes on operation

Names of controls and parts

Turning the power on and off

Switching Audio Modes

Adjusting volume

Switching Rotary Modes

About a shortcut

Creating a shortcut

Using a shortcut

Switching screen

Operation assist function

Detaching the front panel

Using the detachable panel

How to remove the detachable panel

How to attach the detachable panel

How to operate the CD/MP3/WMA player

About compact discs

About brand new CDs

About CD accessories

About borrowed CDs

How to remove CDs

About irregularly-shaped CDs

About cleaning a CD

About MP3/WMA

What is MP3/WMA?

Playable MP3 file standards

Playable WMA file standards

ID3/WMA tag

Media

Format of discs

File names

Multi-sessions

Playing MP3/WMA

MP3/WMA playing time display

Display order of MP3/WMA file/folder names

Listening to CD

TRACK (FILE) UP/DOWN

FOLDER UP/DOWN

Returning to the root directory of the CD (MP3/WMA file)

FAST FORWARD/REWIND

SCAN/REPEAT/RANDOM

FOLDER SCAN/REPEAT/ RANDOM

DISPLAYING TITLE

Ejecting the disc

How to operate the USB music file player

About playable USB memory standards

Playable MP3 file standards

Playable WMA file standards

Format of USB memory

How to operate the USB music file player

Listening to music files in USB memory

Disconnecting USB memory

The Bluetooth audio function

About the Bluetooth audio function

About the Bluetooth specifications

Supported Bluetooth specifications

Supported profile

What is Bluetooth?

Listening to music

Stopping the music

Pausing the music

Selecting the music you want to listen to

Fast forward/rewind

Displaying the BT Audio Set selection mode

Switching the Bluetooth audio mode on and off

Bluetooth audio setup

Connecting the main unit and the portable device

Disconnecting the main unit and the portable device

Displaying device information for the main unit

How to operate the tuner

Listening to the tuner

Tuning to a station

Operations during rotary mode

Automatically storing stations into memory. (The automatic preset mode: ASM)