Eclipse EA Series, XA Series, ZA Series, EA Owner's Manual

ECLIPSE

E:A,

S~&~wit4.&d#uu

XA,

and

Amplificateurs

Manuel

L'e~

4~ti~

E:A,

XA,

.wee

&d#uu

l.d

ZA

MUal

.,14

S6Hie4

&~

e-

&d#uu

ZA

Owner's

du

Serie

del

Series

Amplifiers

Manual

E:A,

XA

proprietaire

de

Amplificadores

Usuario

et

ZA

For

your

safety

in

using

the

EA,

XA

and

ZA

Series

Amplifier

Warnings and caution signs, illustrated below, are posted throughout this manual.
They show safe and correct ways to handle the product to prevent personal injury to
you and others and to avoid damage to property.
Before reading through the manual, take time to read through and learn the important

in

information listed

&Warning

~Caution

this section.

This "Warning" sign indicates a situationinwhich incorrect
handling through disregard
personal injury.

This "Caution" sign indicates a situation in which incorrect
handling through disregard
or may result solely in damage to property.

of

a sign may result in death or serious

of

a sign may result in personal injury

&Warning

may

of

or

cause

• This equipment requires 12V DC and
should only be installed in a vehicle with a
12V negative ground electrical system. Any

may

other installation
severe damage to the equipment and the
vehicle.

• Do not disassemble
Accidents, fires

• Do not let water

may

of

result.

internal parts
or shocks

• Do not use when it is broken. Accidents,

fires or shocks may result.

cause a fire or other

or

alter this equipment.

or

shocks may result.

or

foreign objects enter the

this equipment. Smoke, fires

• Always replace fuses with fuses
identical capacity and characteristics. Never
use a higher rated fuse than the original.

of

Using the wrong type

or

fire

•
equipment, smoke comes out, or there is
a strange odor, stop using it immediately,
and contact your dealer. Accidents, fires,
shocks
in these conditions.

• Plastic bags and wrappings
suffocation and death. Keep away from
babies and children. Never put bag over
your

severe damage.

If

foreign objects or water enters the

may

resultifyou continue to use it

headormouth.

fuse may cause a

• When changing the installation location for
this equipment, please consult the dealer
where you bought it for safety reasons.

is

Expertise
installation.

• Keep volume to a reasonable level so that
you can hear sounds from outside the vehicle,
including warning sounds, voices, and sirens.
Failure to do so may cause

• Do not touch the heat dissipating part

amplifier. Bums may result from the heat

this part.

• Do not use this equipment except for in-

vehicle use. Shocks or injuries may result.

necessary for removal and

an

accident.

LhCaution

• Be careful
turning the power source ON. Hearing damage
may result
the power is turned ON.

Do

not operate under abnormal conditions

•
such as when the soundisdistorted or cuts
out. Fires may result.

• If placed
heat, resulting

of

the

of

• Ifthe equipment is dropped orthe case
broken, turn off the power to the main unit and
contact your dealer. If used in this condition,
fires or shocks may result.

3

of

the volume position when

if

very loud noiseisemitted when

in

direct sunlight, metal parts may

in

the possibilityofburns.

is

About Your Amplifier

Thank
Your Eclipse Power Amplifier was Designed and Engineered
performance and Manufactured with the best components possible.
the best performance
authorized Eclipse Dealer. If you decidetodo your own installation itiscritical that
you read this Manual to help understand the steps necessary to get the maximum

J:

performance from your new product. These Power Amplifiers are designed with the

~

appearance similartoa Beautiful set of polished wheels and should

<:5

respect to protect the Beauty and Integrity ofthe Product.

You

for Your Purchaseofthis Eclipse Mobile Power Amplifier.

in

your system we recommend a professional installation

in

the USA for the best

In

order to realize

be

treated with

Z

W

Planning the Installation

Before installing this Amplifier

and tune the controls for proper matching between the Source Unit, the Amplifier and

the Speaker System.

1.

Amplifier

enough space for mounting hardware to be applied to the Four notches
in

the baseofthe product. Find a location for the Amplifier that will allow
adequate ventilation for cooling. Even though this product
is a power product and will require some air flow for the best cooling. Make
sure the installation location is
contamination. Never install this product

2.

Wiring: Make sure the wiring to and from the Amplifier is protected from possible

short circuit by sharp metal components or metal parts that can damage wiring

when the car
walls or metal sections of the car should have grommets installed

protection against short circuits due

Location:

is

reassembled after the installation. Wiring passing through fire

The Amplifier should be mounted to a flat surface with

be

sure you understand the features and how to adjust

is

very efficient it

in

a dry area away from possible water or liquid

in

the engine compartment.

on

them for

to

vibration and age.

by

in

an

Installing the Amplifier

1.

Before You

safe installation by eliminating the risk of having shorted power wiring while working
on the car.

Note:

You

start:

may refertoCrossover Frequency Selection before Mounting

Disconnect the negative battery terminal. This will ensure a

the

Amplifiers.

4

Installing the Amplifier

2.

Mounting the Amplifier:After a suitable location has been selected and the

wires routed, the Amplifier can be attached to the Vehicle. Start out by removing

of

the Polished Aluminum Trim Covers from the top
Hardware and the Wire Connections can be made. Set these aside
so they can be reinstalled after the Amplifier installation
location space is limited the Polished end covers may all
overall size

Lt

Caution

of

the Product.

Never use a power tool to drive the mounting hardware while
mounting this product. The Drill Chuck will damage the Heat Sink and Possibly
the Connectors! The wiring can be connected to the Amplifier before or after it is
attached to the Vehicle. Dressing the wiring is easier to do after all connections are
made.

3.

Power Connections: Pay attention to the polarity of the wires as

them to this product. We recommend at least 8 AWG Wire for connection between
anyone

of

the Amplifiers Battery Connectors and the Vehicle. The Power connectors
will accept wire as large as 4 AWG. For the best performance and lowest voltage
drop the

wire should

be

as large as possible. It is also recommended that a Fuse

B+
be placed within 18 inches of the positive Battery Terminal to protect the Car from
possible short circuits between the Amplifier locations and the Battery. The ground

B+

wire will carry the same current as the
The ground wire does not have to run all

in

because the Car Chassis

most cases is the same ground as the negative battery

wire so it should

of

the way to the Negative Battery terminal,

terminal. A good ground screwed or bolted to the chassis where the paint has been
carefully removed and conductive grease applied will provide a lasting reliable
connection.

the Amplifier so the Mounting

in

a safe location

is

complete. Ifthe Amplifier

be

removed reducing the

You

connect

be

at least the same size.

m

z

G)

r-

-

(J)

:c

+BATT.

REMOTE

GND

LtCaution

000

---

----

-------

._,,"

..

-

_._---_

..

__

---

-

000

._-----------

---

_.~_.-

Be Sure

--

._-----~

---------

1---

--------

---'_.

- -

ATTENTION

To

Check Polarity

Before Connecting.

(Connections may Vary)

o

Note:

Alternator Stand and the Vehicle Chassis to make sure that it
current

Strip about 5/8 inch (16mm)
connected to the Amplifier.

Optional: For that clean install you may wish to "tin" the bare ends

soldering iron before connecting to the amplifier.

With the Allen (Hex Key) wrenches provided back the hardware out enough to insert the wires
into the Power and Speaker Connectors and connect the wiring to the Amplifier being careful
to not overtighten and possibly strip out the Mounting Screws. Connect the RCA Connectors to
the Amplifier.

You

should check the Ground Wire between the Battery and the Vehicle Chassis and the

is

large enough to carry heavy

in

the case that multiple Amplifiers are installed.

of

insulation from the Power and Speaker wires that need to be

of

the wiring with a

5

Adjusting the Amplifier

Crossover Frequency Selection: Please refer to (Fig1)for a reference to frequency

of

Selection for different models

1.

Select the filter type based on the Amplifier Model and the Application Type.

or

"Hi Pass

2.

Select the Crossover Frequency for Your typeofApplication and adjust the

Low Pass"

Control on the Amplifier. Refer to the Diagram for frequency position

J:

(J)

-

-I

C>

Z

W

58 I 100

50 "

48 - (

46 /

80

\ I

~~-~\

+\;

\ '

\ /

'https://manualmachine.com/

I \

/140

-170

"180

Amplifiers.

55 I

\ I

-'

/

,I

..

~

/

\

\,

"--_/

I \

50"

45

40

70

. !

100

'.

..

\.

;'

//

)75

-300

"

400

45 Hz 200

XAlZA LP Filter

35 Hz 500

XA4200

HP/LP Filter

FIG 1

EA4200

HP/LP Filter

Bass Boost Adjustment:

1.

If Bass Boost is Required
Boost EO Band on the XA1200 and the ZA1200.

2.

Select the amountofBass Boost and make the adjustment to the control.
Refer to the diagram for the amount

Please Refertothe Diagram for selecting the CenterFrequency. The EA4200 and
the XA4200 have

Note:

You

may wishtoadjust the Bass Boost by listening after the systemiscompleted.

a fixed center frequency at 45

45

40

\

38,~-~

48

I

I

/54

2.5,

You

may adjust the Frequency Center for the Bass

6

5

I

\

//--~,

I

7.5
/8

of

BoostindB.

Hz.

3.5 6.5

4

5

35-

(~\

/'

33

32

"'--'/

I

Hz

-60

/,

62 0.5

\

64

0.75-'~

Bass Boost

Frequency ZAlXA 1200

ZAlXA1200

-8.5

/'

"'---~/

I

0

Db

/-.......

\

9.5

9

dB

0

Bass Boost Bass Boost

XA4200

6

9.5

dB

0

8

Bass Boost

EA4200

6

Amplifier

*Ifa subwoofer level control is used with this application at this time Turn the Control

full Clockwise (up all the way).

1.

Adjust the sensitivity controls full counterclockwise C8 V setting

Use a CD or DVD with High Energy Music and adjust the Gain to about 80%

of

the Source Units Maximum output. Make sure the Balance and Fader are

Center Positions. Make sure the Bass and Treble are boosted on the Source Unit.

2.

While playing Music increase the Amplifier Gain to a Point

in

distortion
Amp Gain Controls You May Fine Tune them individually with the entire system
running at a lower overall level. It is recommended that while tuning from this
point, Individual Amplifier Gains can be Attenuated to compensate for System
Balance.

the Music. Adjust eachofthe amplifiers individually. After setting the

Gain

Adjustment:

just

3 2.25 1.75

\ I /

4

"i/:?'~,

).

below audible

/"

1.35

in

m

Z

G)

r

-

(j)

:c

7

7.5 1.5

8 V 1.2

Gain Settings

EA4200

( \

7 - ( ) - 1.3

/

\~!J!"

7.5

/ \ 1.25

8 V

Gain Settings

XAand

1.2

ZA

7

Troubleshooting

Ifa problem occurs after your system is installed, please refer to this troubleshooting

section for solutions.

J:

en

-

~

(!)

.:z

UJ

1.

2.

Problem Possible

Amp

wont

Amp

Blows Fuses Power Cables in Reverse Make sure B+ and PWR GND

power

on No fuse installed in the Install new fuse

amplifierorfuse is blown.
Ground Cable is not con- Check for 12V between B+

nected

Remote line
powering on measure for voltage Between

Polarity cables connected to the correct

Wrong size fuse installed in
amplifier

Cause

in

is not After turning Source on

Possible Solution

amp connector and Amp
Ground Connector: Make sure
ground Cableisconnected to
both amp and car Ground

amp power ground and remote
terminal. Make sure remote
wire is connected to the
Correct remote output from the
source unit. Check connections
and power at source unit

terminals: Connect correctly
Make sure fuse size

Check spec Sheet ( back
this book ) for correct size

is

correct:

of

3.

Amp

from one

is on but no sound RCA cables not connected Make sure RCA cables are

or

more channels

Defective

Speaker wires

Speaker wires connected to

wrong terminals

Input Gain Controls turned
down

RCA

Cable Test RCA Cable for Signal:

not

connected

connected on both ends: Make
connections

Replace if necessary

Make sure speaker wires are
connected on Both ends:
Make connections

Make sure speaker wires
are connected

terminals

Make sure gains are adjusted
to source unit:

To

the correct

8

Troubleshooting

Problem Possible

4.

Amplifier goes into protect

mode

5.

Amp

has

engine noise

One

or more speakers

shorted

Input Gains turned
with

a low Impedance

Speaker ground
car body

is

Cause Possible Solution

are

uptofar,

Load

shorted

Make
speaker
With
disconnect
and

test

Speaker.
Test

speaker
the

car.

With
and

amp
short
output
of

the

Turn
Down.

to

Test
Make
leadisnot
chassisorbody.

sure

shorts:

the

amplifier

for a

for a

short

and

the

speakers

turned

between

And

car.

Input

for

negative

sure

there

the

Sensitivity

negative

shortedtocar

are

no

turned

speaker

short

chassisorbody

from

across

between

connected

off

Test

the

amplifier

chassisorbody

Control

speaker

speaker

off

amp

the

for a

short:

the

-

of

m

Z

G')

h

...

~

.:J:

6.

Distorted Output

Outer barrel of
torisshortingtothe Amplifier
chassis

Amplifier gain

Too

much

Damaged Speaker

Source Unit output
distorted

RCA

is

too

input signal

is

connec-

high

With

amp

off,

RCA

Cables
impedance
of

the

RCA
ground.Ifno
lead

short,

nearly

Call
Turn

so
audible

Source
then8Volts
at

Check
Source:

Test

system
function
Replace

shorted

Eclipse

amplifier

Audio

distortion.
unit

Source

Speaker

Replace

Source

likeaDisplay

verification

levelisjust below

Unit

Source

disconnect

And

test for

between

and

the

negative

the

impedance
(low

Technical

gain

output

RMS:

with

Speaker

Unit

with

Unit.

the

the

Barrel

amp

power

speaker

Is

resistance).

support.

down

levelismore

Reduce

alternative

unit.

gain

alternate

or

7.

Unit Pumps

on

and

off

Speaker

Poor connection
wires or Poor Battery
connection Power Cable connections.

is

shorted

Test

for shorted speaker:
Remove short
or replace shorted Speaker.

to

Power

9

Test

connections at
and

Power Ground: Repair

from

speaker,

B+

cable

Troubleshooting

8.

Poor Bass Output

J:

(J)

-

-J

(!)

Z

W

Poor Bass Output

Problem Possible Cause

Gain Control for Subwoofer is

too low

Crossover is set up

incorrectly

Subwoofers are wired out
phase

Acoustical misalignment
subwoofer

Tone Controls on Source Set
Incorrectly

of

of

Possible Solution

Check Source Unit settings
and Input Gain Control:
Adjust gain control on Source
unitorat amplifier Input.

Check crossover freguency
settings: Adjust Crossover

Check subwoofer wiring
and phase: Correct wiring of
subwoofer to beinphase.

Check to be sure the
box is not to small for

the Subwoofer operating

parameters: Correct box size

Check to make sure the
tone controls are set
flat position and not to cut

position: Set tone controls to
flatorby pass position.

To

a

9.

Speaker pops when unit

turned on or off

10. Bass Boost Distorted

Source unit is sending pop

is

noise to amplifier

Possible ground loop noise

DC offset at amplifier output

Input gain set too high or
remote sub level control is
turned all the way up

Bass Boost Level Too High

Disconnect RCA inputs then
turn source unit

Ifpop noiseisgone try a
different Source Unit.

Check to make sure grounds
are correct so
can exist: If poor grounds
Correct the grounding.

Measure the amount of
voltage across The speaker
connectors at the output
the Amplifier: Ifthe
voltage at the amplifier output

Is

greaterthen 70mVitwill
cause a turn
the amplifier.

Check gain settings: readjust
gain settings with remote sub
control at center position

Readjust Bass Boost Level
and Amplifier Input Sensitivity
with Bass Boost Gain at the
Boosted Level.

on

and off:

No

ground loops

DC

offset

on

sound. Change

DC

of

10

11.

Amp runs hot

T

rou

Inadequate ventilation

bleshooti

ng

Make sure unit has proper

ventilation:

Load impedance

12. Amp wont shut off

Note: If after carefully following these instructions you still have a problem, please

contact Eclipse Technical Support at 1-800-233-2216

Remote on wire
high or at 12V

is

too low

is

staying

Check load impedance
against the specifications:
Connect the proper load
impedance.

Measure voltage between
Remote on terminal and the
power ground terminal:

Ifthe voltage is high
disconnect the Source Unit
And see if the amp shuts off.

If it does try a different source
unit.

m

z

G)

r-

-

en

:c

11

Specifications

EA4200 / XA4200

Power Output: RMS Power at 14.4 Volt Power Supply @

EA4200

40

@ 20 Hz to 20 KHz Stereo

I

~

...J

C)

20
40

@ 20 Hz to
@ 20 Hz to 20 KHz Bridged

20

KHz Stereo

XA4200

Z

W

40

@ 20 Hz to 20 KHz Stereo
20
40

Max Power Output: Peak Music Power at 14.4 Volt Power Supply

40
40

@ 20 Hz to 20 KHz Stereo
@ 20 Hz to 20 KHz Bridged

EA4200

Stereo @ 1 KHz
Bridged @ 1 KHz

XA4200

CEA

2006

60WX4
70WX4

140W X 2

100W X 4

200W X 4

400W X 2

100W X 4

170W X 2

40

Stereo @ 1 KHz

40

Bridged @ 1 KHz

Input Sensitivity

Low / High Pass Frequency Selection Variable (EA4200)
Low / High Pass Frequency Selection Variable (XA4200)
Bass Boost
Subsonic Filter
Signal to Noise
Frequency Response

Frequency Response
Channel Separation
Damping Factor
Quiescent Current
Maximum Current (EA4200)

(CEA 2006)
20Hz - 20KHz (EA4200)
20Hz - 20KHz (XA4200)

(CEA 2006) >80

( Idle Current) - 1.2Amp

30A Maximum Current (XA4200) 100A

250W X 4
600W X 2

1.2V- 8V

32

Hz-

500 Hz

40 Hz - 500 Hz

@45

8dB

18dB / octave @ 20Hz

>

80

+0, - 3

+0, - 0.5 dB

<

70

Hz

dB
dB

dB

Amp Protect Temperature

Dimensions (EA4200)
Dimensions (XA4200)

NOTE: Specifications are subject to change without notice.

( Heat

Sink)

90° C

7.5" (190mm) X 2.36" (60mm) X 10.1" (256mm)

12.2" (310mm) X 2.36" (60mm) X 10.1" (256mm)

12

Specifications

XA1200 / ZA1200

Power Output: RMS Power at 14.4 Volt Power Supply @ CEA 2006

XA1200

40

@ 20 Hz to 20 KHz Mono

500W X 1

20

40
20

@ 20 Hz to 20 KHz Mono

@ 20 Hz to 20 KHz Mono

@ 20 Hz to 20 KHz Mono

ZA1200

1000W
1000W

Max Power Output: Peak Music Power at 14.4 Volt Power Supply

XA1200

40

Mono @ 1 KHz

ZA1200

40

Mono @ 1 KHz 1200W X 1

Input Sensitivity
Low Pass Frequency Selection Variable (Linkwitz Riley 18dB/Octave)
Bass Boost
Bass Boost Frequency Selection

o- 8dB Cont. Variable

32Hz - 64Hz Cont. Variable

40 Hz - 500 Hz

500W

X 1

X 1

X 1

700W X 1

1.2V-8V

m

z

G)'

.

r-~

-

CJ)

.,..,..'

....

Subsonic Filter
Signal to Noise
Frequency Response
Damping Factor
Damping Factor
Quiescent Current
Maximum Current (XA1200)
Maximum Current (ZA1200)
Amp Protect Temperature

Dimensions (XA1200)
Dimensions (ZA1200)

18dB
(CEA2006)
20Hz - 20KHz

(CEA 2006) (XA1200)
(CEA2006)

(Idle Current)

(Heat Sink) 90° C

(ZA1200)

10.2" (260mm) X 2.36" (60mm) X 10.1" (256mm)

12.2" (310mm) X 2.36" (60mm) X 10.1" (256mm)

I octave @ 20Hz

>

80

dB

+0,

-.5

dB

>90

>100

-1.2Amp
100A
160A

NOTE: Specifications are subject to change without notice.

13

Controls

EA4200

I

en

-

.....J

.(9

Z

W

FILTER

LON, rHI OFF,

! • J

BASS

BOOST

5G{Q}

o dB 8

9G

8 V

--

2

MONO

rON

lOW,

i.

!

CROSSOVER

~[CJ

BASS

7G8

30

Hz 500 0 dB 8 30Hz500

-INPUT

12

FRONT--

10G

--

8 V 1.2

3

FILTER

BOOST

rHI

MONO

OfF,

CROSSOVER

g

-INPUT

REAR--

~

rON

l~==============

1-3 Hi / Lo Pass Filter Selection Switch
(Front and Rear)

2-4 Mono Selection (Front / Rear)

5-7 Bass Boost (Front / Rear)
6-8 Crossover adjustment (Front / Rear)
9-10 Input Level (Front / Rear)

r

LINEIN1

FRONT

1

REAR

XA4200

2 3 4 5 6 7 8 9

INPUT LEVEL

,I,

"8)'"

-.

. ; - !\ ) -

,

,,~-~,

I \ I \ I \ I \ I \ I \

8 V

1.2

+BAn

REMOTE

70-FILTER

,I/~

'(~"~"'\'

''''--.--:/"'

40 Hz

500

FRONT

-,

BASS BOOST INPUT LEVEL

,'I

~

HI

';sn~\'

LOW - " ) - \ .

,

~.,

a dB 8 8 V

,I,

'(e~'"

",=./'

1 LineIn(Front and Rear)

2-6 Input Level (Front and Rear)

3-7 Filter Frequency adjustment

4-8 High or Low Pass Filter switch

5-9 Bass Boost Adjustment

RIGHT

FRONT

GND

FUSE

-+-+-+-+

LEFT

70

- FILTER

\1/~

':~/~\'

.I

- " ) -

,\.~.,

1.2

40Hz500

REAR

RIGHT

REAR

LEFT

-,

~

HI

LOW - . -

BASS

BOOST

,II

'·sn---=-·"·'

,\,._/

a

dB

'

8

~:

l=~=:~

000

- - ..

o

·BRIDGED--

14

+ 0 -

.-

BRIDGED

- +

Controls

XA1200

1~-_O_~

FRONT

€)

OJ OJ

~~

~

1 Line Input
2 Input Level
3 Bass Level Control

40A

FUSE

40A

8 V 1.2

INPUT
LEVEL

DoD

2 3

rffiffIl

~

LEVEL

CONTROL

+BATT

".--~"

,~_/'

.'

"

REMOTE

,,-,

----'

0

6

, I ,

'.~'-""

•.

\ \

,\.~/,

, ,

o

Db

8

'

"-

45Hz200

LOW PASS

-,/

32Hz64

FREQ LEVEL

BASS BOOST

4 Low Pass Filter Frequency Selector.

5 Bass Boost Frequency Selector

6 Bass Boost Level Control

SPfAKER

GND

/---

........

\_---~

OUT

I

'~'~~I

W

~

0

IT

2

G:

r

-

CJ.

::I

~

1

FRONT

@

OJ OJ

@

1 Line Input

2 Input Level

3 Bass Level Control

, , , ,

, '

"e2'

-,

<,,--_.://

,

8

INPUT

LEVEL

2

I

....

-

,

V

12

ZA1200

__

3

~

LEVEL LOW PASS

CONTROL

C)_~

4

80

I

- (

\ \

'eJ'

...

\'''::~-

~./

,

45Hz200

5

45

, I ,

'~-="'--"

\-

- I

\ '

....

,

,

-"'-~'

, ,

32

Hz

64

FREQ LEVEL

BASS BOOST

4 Low Pass Filter Frequency Selector,
5 Bass Boost Frequency Selector
6 Bass Boost Level Control

SPEAKER

-

J-

OUT

6

, I ,

, ,

'~-~'

'-

\ \

'\~-'~

, ,

o

Db

,

8

o

15

(ECLIPSE

.

SN

29344722

Fujitsu
Contact: Fujitsu
19600 So. Vermont Avenue, Torrance, CA90502
Call:

Fujitsu
Communiquez
19600 So. Avenue Vermont, Torrance, CA90502
Telephonez

Fujitsu
Contacto : Fujitsu
19600 So. Vermont Avenue, Torrance, CA 90502
L1ame: [phone] www.eclipse-web.com

Ten

Limited

Ten

Corp.ofAmerica

[phone] www.eclipse-web.com

Ten

Limited

Ten

avec:

au

: [phone] www.eclipse-web.com

Limited

Fujitsu

Ten

Corp. d'Amerique

Ten

Corp. d'Amerique

Fujitsu

Ten

Corp.ofAmerica

LECLIPSE

i

Garantie limitee

du

consommateur

Garantie valable uniquement aux

E.U.

et au Canada

Cette garantie limitee fournie par Fujitsu Ten Corp.ofAmerica ("Eclipse") couvre, sous utilisation normale, toutes defectuosites materielle et main
d'ceuvre de votre nouveau produit Eclipse achete chez

detaillant agree Eclipse aux E.U.ouau

Canada, pendant une duree de une (1)

an

nee a

un
compter deladate d'achat d'origine. Cette garantie limitee est valable seulement pour I'acheteur consommateur initial du produit Eclipse qui doit resider
aux E.U.

Les rel;us
pourrait

ouauCanada, elleNEpeut PAS etre transferee.

ou

autres preuves

vous

facturerourefuserdevous

admissibles

d'achat

rendre Ie

service

montrant

pourIeproduit

la datedeI'achat

Eclipse

initial

sans

sont

preuve

requis

d'achat

pour

la garantiedece

valable.

produit.

Eclipse

CE QUI EST COUVERT
SiIeproduit devient defectueuxaupoint de vue materiel
de la date d'achat initiale, Eclipse reparera votre produit Eclipse,
ou

remplaceraIeproduit parunproduit recycle identiqueouun modele fonctionnellement equivalent. Eclipse conservesapropriete sur toutes les

pieces engagees ou produits remplaces sur

la

base d'une substitution. Eclipse vous reexpediera I'element et couvrira les frais d'expedition.

ou

main d'ceuvre ala suite d'une utilisation norma

a

sa

discretion etcesans frais, avec des composantesoupieces neuves ou recyclees

Ieaucours de la periode d'un (1)

an

apartir

CE QUI N'EST PAS COUVERT

1.

Cette garantie limiteenecouvre aucun produit repare par un individu,undetaillantouun

centre de service non agree,niaucun produit achete aupres

d'un detaillant non agree.

2.

Cette garantie limitee ne couvre aucun produit ayant fait I'objet de mauvais traitement, d'un mauvais usage, de negligence, d'un accident, de
modifications, de mauvaise connexion avec des peripheriques, d'une tentative de vol, de surtension electrique, de dommages par

ou

d'inondation, de dommages par la foudre

ouendehors des limites de specificationsouayantunnumero de serie altere, degradeouenleve.

Eclipse

3.

Cette garantie limitee ne couvre pas I'elimination de I'electricite statique delavoiture,Iebruit du moteuroules autres interferences electriques, les
corrections de problemes decoulant de media inappropries tels que CD, DVD

la

defectueuse et

4.

Cette garantie limitee ne couvre pas les dommages cosmetiques y compris aux panneaux frontaux et aux affichages de type LCDouTFT, I'usure
normale,

Ie

desactivationducode de securite pour les produits contenant la fonction Numero de serie electronique (NSE).

remplacement delabatterieoula

5. Cette garantie limitee ne couvre pas les dommages causes par les produits Eclipse aux media tels que CD, DVD

6.

Cette garantie limitee ne couvre aucune de vos depenses acquitteesoucontracteesenrapport avec cette garantie. Vous etes, par exemple,

autres actes delanature, qui ont ete utilises de maniere autre que selon les instructions fournies par

ou

carte memoire,Iesysteme d'antenneduvehicule et son installation

maintenance reguliere.

ou

autres, y compris leur contenu.

un

liquide,

responsable de I'enlevement et de I'installation du produit ain5i que I'expedition vers Eclipse, les frais d'expeditions et tout dommage pendant
I'expedition.

7.

Cette garantie limiteenes'applique pas lorsque les produits sont utilises dansuncommerce, une entreprise ou toute application industrielle

ou

commerciale.

A

LA

COMMENT OBTENIR LE SERVICE ASSOCIE
Certaines instructions de produits Eclipse fournissent des procedures de diagnostic pour

GARANTIE

determinersivotre

produit

necessite Ie service.Lasolution

la plus rapide peut etre trouvee dans les instructions. Veuillez d'abords regarder ici.
Si

vos HAUT·PARLEURSDEVOITURE Eclipse requiert un service, veuillez contacter, pourIeservice,Iedetaillantouvous avez acheteceproduit.
Pour d'autres produits Eclipse, contactez votre detaillant
besoindeservice, veuillez appelerouvisiter
instructions de reexpedition fournies sur obtention du numero de reclamation.

notre

ou

vous avez acheteceproduit pour verifier queIeproduit requiertunservice. En cas

site

Web

ci-dessous

pour

Eclipse

obtenirunnumerodereclamation. Vous devez suivre les

N'ACCEPTERA

aucun

produit

sans

numerodereclamation.

de

Centre agree de service apres-vente de Eclipse

1-800-233-2216 pour les consommateurs des E.U. SEULEMENT /1-888-557-8278 pour les consommateurs du Canada SEULEMENT

ou

www.eclipsediamondservice.com

DE

AVIS
Tout logiciel de systeme de navigation fourni avec les produits Eclipse est fourni
logiciels de systeme de navigation peuvent contenir des bogues
n'auront aucune responsabilite envers vous

Eclipse ne sera responsable d'aucun logiciel, d'aucune donnee
soit, dansIecadre de la garantie, y compris les
du service de

NON-RESPONSABILITE POUR LOGICIELDESYSTEMEDENAVIGATION ET DE STOCKAGEDEDONNEES

ou

en

rapport avec I'utilisationouIe

coUts

la

garantie du produit,Iecontenududisque duroutout autre media de stockage de donnees est altere, efface, modifieouegare, Eclipse

de retablissement de tels programmes informatiquesoude telles donnees.Sipendantlaperiode

erreurs et peuvent donner des directions erronees. Eclipseouses marchands

ou

autre information stockee

« tel quel

mauvais usageoude la dependanceaulogiciel de systeme de navigation.

»,

avec tous ses defauts et sans garantie quelconque. Les

ou

utilisee sur quelque produit retourne a Eclipse que

n'est pas responsable.

NON-RESPONSABILlTfETLIMITATIONDERESPONSABILlTfDELA

CEnE

DECLARATIONDEGARANTIE POUR LE PRODUIT ET LE LOGICIEL VAUT POUR TOUTES LES
GARANTIES FORMELLES, TACITES OU LEGALES, Y COMPRIS MAIS NON
TACITES
DU
NE
FORMELLE TELLE QUE PRESENTEE CI-DESSUS.
MATERIEL
REMPLACEMENT TEL QUE STIPULE CI-DESSUS. CEPENDANT,SICE RECOURS NE REMPLIT PAS SON
OBJECTIF ESSENTIEL, ECLIPSE SE RESERVE LE DROIT
PRODUIT AL'ACHETEURENECHANGEDURETOURDUPRODUIT. ECLIPSENESERA PAS PASSIBLE
DOMMAGES ET INTERE:TS Y COMPRIS MAtS NON
ACCESSOIRES

INTERRUPTION
PREJUDICE (Y COMPRIS LA NEGLIGENCE ET LA RESPONSABILITE ABSOLUE, MAIS EXCLUANT

L'AnEINTE

LES DROITS DANS VOTRE
CERTAINS ETATS N'AUTORISANT PASDELIMITATIONSDEDUREE POUR UNE GARANTIE TACITE
L'EXCLUSIONOULA LIMITATIONDEDOMMAGES ACCESSOIRES
LIMITATION OU D'EXCLUSION PEUTNEPAS S'APPLIQUER A
DES DROITS LEGAUX PRECIS, VOUS POUVEZ AUSSI DISPOSER D'AUTRES DROITS QUI VARIENT D'UN
ETAT

DE

PRODUIT ECLIPSE. TOUTES LES GARANTIES TACITESOULEGALES, DANS LA MESUREOUELLES

PEUVENT PAS

QUALITE MARCHANDEOUD'APTITUDE POUR LA REALISATION D'UN BUT PARTICULIER

E:TRE

OU

MAIN D'OEUVRE, VOTRE RECOURS UNIQUEETEXCLUSIF SERA LA REPARATION OU

ALA PERSONNEl,

A

UN

AUTRE

EXCLUES, SONT

OU

CONSECUTIFS, PERTE D'UTILISATIONDEDONNEES, PERTE

DE

L'EXPLOITATION, QUE CES DOMMAGES SOIENT BASES SUR LA GARANTlE, LE

LE

CONTRATOUL'INDEMNITE.

fTAT

L1MITEES

A LA DUREE EFFECTIVE

SILEPRODUIT EST DEFECTUEUX AU POINT DE VUE

L1MITES

GARANTIE

L1MITEES

DE

REMBOURSER LE PRIX D'ACHAT

AUX DOMMAGES DIRECTS, INDIRECTS,

OU

vous.

CONSECUTIFS,CETYPE

CEnE

GARANTIE VOUS ACCORDE

AUX GARANTIES

DE

LA GARANTIE

DE

PROFITS OU

LE

DU

DE

1111I111111111111111111111I1111111111111

EA4200

NI

DE

ce

LEG002; Veri 4.1 29365133

Fujitsu Ten Corp.ofAmerica

Consumer Limited Warranty

Warranty valid onlyinthe U.S.A. and Canada

This limited warranty provided by Fujitsu Ten Corp.ofAmerica ("Eclipse") covers all defectsinmaterials or workmanship under normal use in your new
Eclipse Product purchased from an authorized Eclipse retailer in the U.S.A. or Canada for a period
purchase. This limited warranty is valid only for the original consumer purchaser
and is NOT transferable.

Sales

receiptorother

may

charge

youorrefuse

WHAT

IS COVERED
If the Product becomes defective
consumer purchase, Eclipse will, at its option and without charge, repair your Eclipse Product with new
the Product with a reconditioned product
is replaced on an exchange basis. Eclipse will return ship the unit to you and cover shipping charges.

WHAT

IS NOT COVERED

1.

This limited warranty does not cover any Product which is repaired by any non-authorized individual, retailer or service center, or any Product
purchased from a non-authorized retailer.

2.

This limited warranty does not cover any Product which has been subject to abuse, misuse, neglect, accident, Product modifications, improper
connection with peripherals, attempted theft, electrical power surge, liquid damage, flood, lightening, or other acts of nature, which has been used
other than in accordance with the instructions furnished by Eclipse or over the specification range, or which its serial number has been altered,
defaced or removed.

3.

This limited warranty does not cover eliminationofcar static, motor noise or other electrical interference, correctionofproblems resulting from
improper media such as CD, DVD or memory stick, vehicle's antenna system, and faulty installation, and de-activation

Products containing ESN function.

4. This limited warranty does not cover cosmetic damage including face panels and displays such as LCD

replacement

5.

This limited warranty does not cover any CD, DVD or other media damage including its contents caused by Eclipse products.

6.

This limited warranty does not cover any expenses paid or incurred by youinrelation to this warranty. For example, you are responsible for removal
and installation

7.

This limited warranty does not apply when Product is usedina trade or business orinany industrialorcommercial application.

or

valid

proofofpurchase

service

periodic maintenance.

of

the Product as well as shipping to Eclipse, shipping charges and any damage during shipping.

for

the

in

material or workmanship that may arise under normal use during the periodofone (1) year from the dateoforiginal

of

showing

Eclipse

the same or functionally equivalent model. Eclipse retains as its property any retained parts or product that

Product

the

dateoforiginal

without

valid

of

Eclipse Product who must reside in either the U.S.A. or Canada

purchaseisrequired

proofofpurchase.

of

one (1) year from the dateoforiginal consumer

for

warranty

or

reconditioned components or parts, or replace

serviceofthis

or

TFT, normal wear and tear, battery

Product.

of

security code for the

Eclipse

HOW

TO OBTAIN
Some Eclipse Product instructions provide troubleshooting procedures
found in the instructions. Please look here first.

Should your Eclipse CAR SPEAKER require service, please contact the retailer where you purchased this Product for service. For other Eclipse
Products, please contact your retailer where you purchased this Product to verify that the Product requires service.
or

visit

Eclipse

DISCLAIMER FOR NAVIGATION SYSTEM SOFTWARE
Any navigation system software provided with the Eclipse Product is provided "as is", with all faults and with no warranties whatsoever. Navigation
system software may have bugs and errors, and may provide incorrect directions. Under no circumstances shall Eclipse or its LICENSORS be liable

you on accountofuse or misuse of,orreliance on, any navigation system software.

Eclipse shall not be responsible for any software programs, data or other information stored or used on any Product returned to Eclipse for warranty

service, including the costs
other data storage media are altered, deleted, modified or lost, Eclipse is not responsible.

WARRANTY
THIS WARRANTY STATEMENT FOR THE PRODUCT AND THE SOFTWARE IS

WARRANTIES, EXPRESS, IMPLIED OR STATUTORY INCLUDING BUT NOT LIMITED TO ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

ON
THAT THEY CANNOT BE EXCLUDED, ARE LIMITED TO THE EFFECTIVE PERIOD OF THE

EXPRESS WARRANTY SET FORTH HEREIN. IF THE PRODUCT

OR WORKMANSHIP, YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR

REPLACEMENT AS PROVIDED ABOVE. HOWEVER IF THAT REMEDY FAILS OF ITS

ESSENTIAL PURPOSE, ECLIPSE RESERVES THE RIGHT TO REFUND THE PURCHASE PRICE

OF THE PRODUCT TO THE PURCHASER

ECLIPSE SHALL NOT BE LIABLE FOR ANY DAMAGES INCLUDING, BUT NOT LIMITED TO,

DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF USE OR DATA,

LOSS OF PROFITS OR INTERRUPTION OF BUSINESS, WHETHER SUCH ALLEGED DAMAGES

ARE BASED

EXCLUDING PERSONAL INJURY), CONTRACT, OR INDEMNITY.

YOUR STATE

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS

OR

SUCH LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY

FROM STATE TO STATE.

our
will

THE ECLIPSE PRODUCT. ALL IMPLIED OR STATUTORY WARRANTIES, TO THE EXTENT

THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO

WARRANTY

website

NOT ACCEPT

belowtoobtainaclaim

DISCLAIMER AND LIMITATION

IN

WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY, BUT

LAW

RIGHTS

SERVICE

any

Product

1-800-233-2216 For U.S.A. Consumers ONLY / 1-888-557-8278 For Canada Consumers ONLY

of

recovering such programs or data. If during the warranty serviceofthe Product, the contentsofthe hard drive or any

number.

withoutaclaim

IN

EXCHANGE FOR THE RETURN OF THE PRODUCT.

You must follow the return shipping instructions provided when you obtain the claim number.

number.
Eclipse Authorized Service Center:

or

www.eclipsediamondservice.com

AND

DATA

to

determineifyour

STORAGE

IN

LIEU OF ALL

IS

DEFECTIVEINMATERIALS

Product

needs

service.

The fastest solution may be

If

serviceisneeded, please

1111111111111111111111111111111I11111111

call

EA4200

to

LEG002; Ver.

4.1

29365133