tester failure to do so may result in damage
to the tester or injury to the user.
5. Repairs and maintenance must only be
carried out by qualified service personnel or
MINI LAN CABLE TESTER
MT-7058
User’s manual
99 Washington Street
Melrose, MA
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
INTRODUCTION
The mini LAN cable tester complies with CE
safety standard, compact size and lightweight
design for easy detection of good connections,
opens, crossed wires & split pairs by only one
touch testing. Traces wires with tone. Remote
lights allow one person operation. Additional
non-contact voltage detection provides user
safety. Ideal for testing installed cables or
patch cords with RJ-45, RJ-11, RJ12 and
BNC connectors.
SAFETY RULES& WARNINGS
1. Read all instruction in this ma
using this tester. Failure to do so may result
in damage to the tester or injury to the user.
2. Do not use this tester with its case open, or
with parts removed. Doing so may damage
the tester and/or injure the user.
3. When using this tester in schools and
workshops, responsible teachers or skilled
personnel must control the usage of this
tester. Failure to observe this precaution
may result in damage to the tester or injury
to the user.
4. Follow the recommendations of any Trade
Organizations or Regulatory Agencies
whose scope encompasses the use of this
02176
nual before
qualified electricians/technicians who know
the dangers of.
6. Do not apply voltage or current to any of the
tester’s connectors. Doing so may damage
the tester and /or injury the user.
7. Remove the battery when the tester not in
use for longer than a month. Chemical
leakage from the battery could damage the
tester.
PRODUCT FEATURES
1. Complies with CE safety standard
2. Automatically detect good connections,
opens, crossed wires & split pairs
3. Simple one button test
4. LEDs indicate connections and faults
5. Tests shielded (STP)or unshielded(UTP)
LAN cables
6. BNC cable indicator
7. Non-contact voltage detection for user
safety.
8. Long cable test more than 300 meters
9. Low power consumption with auto power
off function to preserve battery.
SPECIFICATIONS
1. Cables Tested: UTP and STP LAN cables
Terminated in RJ-45 male connectors. (EIA/
TIA 568)RJ-11, RJ-12 cables with male
connectors, 2 to 6 connectors installed.
BNC cables with male connectors.
2. Faults Indicated: No Connection, Short,
Straight, and Crossover.
3. Low Battery Indicator: LED lights different
colors to indicate low battery
4. NCV detection for AC60V~240V 60Hz
5. Case Dimensions:100*60*24.5mm(LxWxH)
6. Weight:120g (without battery)
7. Battery: 12V battery. AE23
PRODUCT DESCRIPTION
1. BNC connector
2. Non-contact voltage
indicator
3. Power/sound on/off switch
4. RJ-45/RJ-11/12 connector
5. Auto / manual NCV switch
6. One touch push button
7. RJ-45/RJ-11/12 connector
ACCESSORIES
Female
Instruction
Pouch Bag
OPERATION
1. The MAIN and REMOTE unit:
The Mini LAN Cable Tester consists of a
main unit and a remote unit. The remote
unit stores conveniently on the bottom of
the main unit. It can be removed or
replaced by sliding it from left to right or
right to left respectively.
2. Performing the test:
Once the remote and main units are
attached to the ends of the subject cable,
as described in 3.2 and 3.3, testing may
begin, simply press and release the test
button on the main unit, observe the LED
indicators, and note the beeping sound that
comes from the main unit.
3. Interpreting the results:
3.1 Power LED:
3.2 No connection LED
3.3 Straight/Crossover LED
sounds for 4 times (8P8C 3 times), it
means the cable is all correct connection. If
some of the LEDs do not light up, but
others light up, and the straight LED also
lights up, it means the cable is open.
If some of the LEDs light up inconsistently,
and the straight LED also lights up, it
means the cable may be misconnected.
Please check in turn of lighted LED of
remote unit to identify which wires are
misconnected or change left side switch to
BNC Terminator
Manual
The power LED should lights up
whenever the test button is pressed and
released. If the power LED turns red,
replace the battery. The power LED
also indicate the test result, it will turn
red, except wire in “Straight” condition
will turn green
If the remote is not connected to the
main unit with a cable, or the cable has
no intake conductors, the no connection
LED will light up and the beeper will
sound for 4 times.
When all of the appropriate numbered
LEDs light up, the straight or
LED also lights up, and the beeper
“Step” become manual function to check
crossover
the misconnection status step by step.
Note:
RJ-1
conductors, or 6 conductors. When testing 2
conductor cables, LED 4 ~ 5 must light up, for
4 conductor cables, LED 3~ 6 must light up
and for 6 conductor cables, LED 2~7 must
light up, and “STRAIGHT” LED also lights up.
The numbered LEDs do not indicate a good
connection exists; only shows connection
exists. If “Short” LED lights up during test, it
means the shorted was found in the cable.
3.4 Short LED
3.5 Crossover LED
4. BNC testing:
Numbered LEDs will light up during
scanning, after scanning, both LEDs of
BNC on the main unit and the BNC receiver
will light up. If the BNC cable is short, only
the LED of BNC on the main unit lights up;
if the BNC cable is open, both LEDs of BNC
on the main unit and the receiver won’t light
and “no connection” LED will light up..
5. Non-cont
Set the left side switch to the NCV position
and the right side switch to the Sound On
position. As the antenna is located at the
right top of the tester, close right top of the
tester to the live wires, the LEDs of NCV
will flash with sound.
ables
1/12 c
If 3 & 4 LEDs lights up, an
LEDs do not light up, the cable is
shorted; the “short” LED will light up.
Numbered 1~8 LEDs will light up, and
“Crossover” LED also lights up. Means
wiring one end with 568-A standard,
and the other end with 568-B standard
act Voltage Detection:
Please put the tester as close as
possible to surface of tested
source for optim
y
have 2 conductors, 4
ma
a testing result.
d all other
迷你網路測試器
MT-7058
一、 產品介紹：
MT-7058 是一款集多種線路測試功能及非
接觸電壓測量於一體的多功能纜線測試
器，可測試的線材種類 RJ-45、RJ-11、
RJ-12、BNC。 只需一按開關，所測試線材
狀況一目了然。 線材的斷路、短路、交錯
都一一顯示在主機面板上。
二、安全注意事項：
注意：此測試器不能用於測試帶有電壓之
活線，若將活線接於此測試器，可
能會造成測試器損壞。
** 使用前請細詳閱讀使用說明書，錯誤使
用可能造成測試器損壞。
** 使用時請勿將機殼打開使用或自行更
換內部零件，以免成測試器損壞。
三、產品特色：
雙功能指示：快速結果測試(斷路.交
叉.直通.短路) 與 Pin to Pin 掃描測試
(1-8 LEDs)
網路.電話.BNC 3 合 1：可測試 RJ45
(8P8C)網路線、RJ11/12 (4P/2C. 6P/4C.
6P/6C)電話線、BNC 線與屏蔽指示
聲光雙顯示：具有 LED 燈號與音頻嗶
聲的聲光雙指示功能、電池低電壓指
示、防誤測迴路保護電路
免接觸驗電：具有免接觸驗電功能，
確保網路架設作業的安全，並通過 CE
安規認證
測試距離更遠：採用 12V(AE23)電
池，測試距離超過 300 米
攜帶方便：輕巧迷你的近遠端結合設
計，附BNC 終端電阻. 攜存袋，外出
作業更方便
四、產品規格：
1. 測試線材/接頭：UTP / STP / RJ-11/
RJ-12 / RJ45 / BNC
2. 自動 (AUTO)及手動 (STEP)切換掃
描檢測跳接正確性、短路、斷路及芯
線排列順序等功能
3. 非接觸電壓 AC60V~240V 60Hz 感應
測試(NCV)
4. BNC 接頭同軸電纜連接、斷路、短路
測試
5. 自動待機功能
6. 低電壓 LED 燈色指示
7. 尺寸：100*60*24.5mm (L x W x H)
8. 重量：120 克 (不含電池)
9. 適用電源：12V 電池 AE23
五、本體介紹︰
1. BNC 接頭
2. 免接觸驗電顯示
3. 電源/聲音開關
4. RJ-45/11/12 接頭
5. 自動/手動/免接觸
驗電開關
6. 測試按鈕
7. RJ-45/11/12 接頭
六、配件：
1. BNC
母端接頭
2. 使用說明書
3. 收納袋
4. 12V (AE23)電池
七、顯示面板
及 LED 燈功能介紹：
(1) “S＂燈號：表示遮罩線
(2) “1 -8＂燈號：表示對應的線路。
(3) “SHORT＂燈號：表示線材有短路。
(4) “STRAIGHT＂燈號：表示受測試的
線材連接是正確的或是代表一條扁
平的直通線。
(5) “CROSSOVER＂燈號：表示受測試
的線材連接有交錯的問題或是代表
一條交叉的對絞線。
(6) “NO CONNECTION＂燈號：表示沒
有相通的線，或是接頭沒有插好，有
可能是接觸不良。
(7) “POWER＂燈號:按下測試鍵後亮綠
燈：表示本測試器的電源正常可正常
使用。亮紅燈：表示本測試器的電源
不足，應及時更換電池，以免對測試
結果產生影響。
(8) “NCV＂燈號︰表示接觸電線存在
電壓
(9) “BNC＂燈號︰同軸電纜導通判斷
POWER＂指示燈:電池電量充足
時，主機判斷結束前,顯示綠燈，
若測試結束後顯示紅燈，表示被測線
纜芯線部分或全部短路，交叉和非連
接(short/crossover/no connection).顯示
綠燈表示導通(straight)。 電池電量不
充足時，主機可能無法正常工作.
八、3 種線材及 NCV 的測試方法
1. 測試 RJ45：
主測試器的測試結果皆需搭
配遠端接收器亮燈順序來判
斷線路正確性
把所需測試線插入主測試器和遠端測
試器，按一下開關主機＂STRAIGHT＂
燈亮，而上方對應的 8 顆 LED 燈亮起
順序一致時（如果是 STP 線則＂S＂燈
也會同時亮），表示這條線是連接正確
的線路。
如果＂STRAIGHT＂或“CROSSOVER
＂燈亮，而主測試器和遠端測試器燈
號亮起的順序不一致就表示有交錯或
順序相反。此時只要查看遠端接收器
燈號亮起的順序即可得知是哪幾條線
錯接。
將側面的滑動開關切換至＂STEP＂手
動測試功能，逐一查看主測試器及接
收器 1-8 燈號顯示狀態。
如果＂SHORT＂燈亮，表示有短路，
同時短路的路線與所對應的 LED 燈也
同時亮。
如果＂ST
RAIGHT＂燈亮
，而 LED 燈
有幾顆不亮，表示對應的路線有斷路。
如果＂
CROSSOVER＂燈亮
，就表示這
條線是交叉線。.
2.
測試
RJ-11/12：
如果 6 芯電話線則 LED 亮“2-7＂，4
芯電話線亮“3-6＂，2 芯電話線
“4-5＂，同時“STRAIGHT＂燈也亮。
3. 測試 BNC 同軸電纜：
插入BNC測
試座, 按下測試鍵, 掃描
後若電纜線導通狀態, 則“BNC＂指
示燈亮。若電纜線開路, 則“NO
CONNECTION＂指示燈亮. “BNC＂
指示燈不亮
4. NCV 測試
將左側撥動開關推到 N
：
CV 檔位，並將
本體右測頂端靠近被測體，當交流電
壓高於 60V 低於 240V 60Hz 時，“ N C V
＂指示 LED 閃爍並有響聲警示。
為提高測試靈敏度，請貼近待測
電源表面。
©2013 Prokit’s Industries Co., LTD. All rights reserved 2013001(T)
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipm entDepot.com
Loading...