Test Equipment Depot - 800.517.8431
GS-23K Gas Soldering Iron Kit – Auto Ignition.
Instruction Manual
- 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
Thanks for buying PRO’SKIT GS-23K Gas Soldering Iron Kit –
Auto Ignition. Please read all instructions carefully before using
the product.
SPECIFICATIONS
Iron size Φ29 x 245mm
Gas container capacity 15ml
Operating time About 90mins
(one gas filling)
Soldering temperature up to 500℃
Hot Blow temperature up to 600℃
Torch temperature up to 1300℃
APPLICATIONS
Repair switch board, meters
TV Cable system
Soldering circuit board
Loosen rusted nut and bolts
Sensitive IC board
Jewelry repair
Silver solder
Weld plastics
Automotive / Aviation service repairs
WARNING
1.) Keep the touch out of reach of children.
2.) Read directions carefully before use.
3.) The burn tip and other accessory tips get hot in operation.
Do not touch the tip or accessories, or place them on
flammable objects
4.) Always have a fire extinguisher or bucket of water near
the torch work area.
5.) Always point away from eyes and body when igniting or
operating. Flam is invisibles sunlight; it can cause injury if
used with extreme.
6.) Under no circumstances should you attempt to repair a
damage torch
7.) Do not store under direct sunlight or anywhere that will
exceed 104℉ / 40℃
8.) Do not immerse in water.
9.) Make sure the adjustment knob is firmly closed and the
flame is completely extinguished after using.
10.) Use only in well ventilated areas.
OPERA TION
safety lock button. Slide the continuous flame
switch to right (Fig2) for a constant flame.
Fig2
EXTINGUISHING (Fig2)
Slide the continuous flame Switch to left (OFF), and
this will cut off the gas supply and extinguish the
flame.
HOT BLOWER
Disassemble the soldering tip by rotating the tip
counterclockwise. The assembly will now be used as
hot blower without the soldering tip. Operation will be
the same as above for the soldering iron.
(fig1.)
TORCH
Disassemble the soldering tip and hot blow head
with metal sleeve by rotating counterclockwise. Install
the metal sleeve back to the unit. Operation will be the
same as above for the soldering iron. (Fig2)
FLAME ADJUSTMENT
Slide the adjustment lever toward right side to
increase the flame strength or toward left to decrease
the flame strength.
When the flame is at “+” position, the longer flames
may cause the torch to flare or extinguish. In this
situation, please move the gas adjustment lever to “-”
side for decreasing the flame strength and set up a
most efficient flame(Blue Flame).
GAS REFUEL
1.) Use only high quality butane gas.
2.) Before refilling make sure that the continuous
flame Switch at left (OFF)side. (Fig2)
3.) Follow the directions on butane fuel can. Insert the
tip to filler valve, using a pumping action for best
results
4.) After filling allow the gas to stabilize a few minutes
before ignite.
STORAGE
Make sure that the torch is turned off and cool, before
storing or leaving unstable.
Fig1
IGNITION
1.) Make sure the exhaust vent is facing upward to
avoid the damage of tabletop.
2.) Press the safety lock button and
simultaneously using your thumb to pull down the
trigger. This action will ignite the soldering iron.
3.) Hold the ignition button and release the
TROUBLE SHOOTING
Problem Probable cause Solution
Does not
ignite
Excessive
gas flow
Low gas
pressure
1. Empty fuel
as Pr
2. G
too high or too
low
Setting too high Adjust gas regulator gradually
1. Low fuel
2. Cold fuel
1.
essure
.
2. Slide the adjustment lever
Re-ignite the torch by gradually
increasing the gas.
1. Refuel
2.
Refuel
toward
right or lef
Hold in hands to warm up.
t.
GS-23K 自動點火多功能瓦斯烙鐵組
操作說明
感謝您購買和使用 PRO’SKIT GS-23K 自動點火多功能瓦斯
烙鐵組，使用前請仔細閱讀說明書，閱讀後請妥善保存，以
備查閱。
1. 規格
烙鐵尺寸 Φ29 x 245mm
瓦斯筒容量 15ml
使用時間
烙鐵溫度 500℃
熱風溫度 600℃
火燄溫度 1300℃
約 90 分鐘
(一次完全充填)
2. 產品應用
維修開關電路或馬達
有線電視系統
PCB 焊錫
鬆開生鏽的螺帽或螺栓
敏感的 IC 板
珠寶維修
焊銀料
熔接塑膠
汽車航空服務維修
3. 警示
1.) 將產品放置在小孩拿不到的地方
2.) 使用前仔細閱讀說明書.
3.) 操作完成後請勿碰觸或是將熱燙的烙鐵頭及其他配件放在
可燃物附件.
4.) 在本產品的工作區域附近需放置滅火器或是已裝水的水桶.
5.) 當點火或操作身體及眼睛需遠離熱點，火燄就像陽光一樣時
有可能會造成商害.
6.) 在任何狀況之下都不應該嘗試修復本損壞的產品.
7.) 存放時請不要讓太陽直射或是讓存放溫度超過 104℉ / 40℃
8.) 不要將產品浸泡在水中.
9.) 在使用完成後確認開關及調整鈕為關閉的狀態並確認會燄
是熄滅的狀態.
10.) 請在通風的地方使用本產品
4. 操作說明
產品圖解說明
圖二
熄火
將連續火燄開關撥到左邊，此動作會切斷瓦斯的供應，
火燄隨之熄滅. (圖二)
熱風
逆時針方
作即會產生熱風
向旋轉拆下烙鐵頭後執行上述點火的動
.
火炬
逆時針方
向旋轉拆下烙鐵頭、金屬套管及熱風頭後
再將金屬套管裝上後再執行上述點火的動作即會
產生火炬
.
火燄調整
將火燄調
整開關滑往右邊會加大火燄的強度，往左
則減小火燄的強度，當火焰調整開關在“ + ”的位置
時，可能會導致較長的喇叭形火焰或熄滅，當這種
狀況發生時請將火焰調整開關滑往“ - ”側，降低火
焰的強度並調整成有效的火焰(藍色火燄
填充瓦斯
1.)
請使用高品質丁烷瓦斯
填充瓦斯前請先確認
2.)
圖二)
邊 (
3.) 依照指示在將瓦司罐的填沖頭插入填寫閥
門，並且將瓦斯管罐以重覆壓入放鬆的方式進
行瓦斯填充
4.) 填充完成後，請將產品靜置數分鐘後再進行點
火.
收納存放
收納存放
卻的狀況下進行
或是擱置前時請確認產品為熄火並且冷
.
5. 簡易問題排除
問題 可能發生的原因 解決方法
1.
點不著火
氣體流量過
多
瓦斯壓力太低 1. 瓦斯過少
沒瓦斯
2. 瓦斯壓力太低
設定太高
2. 瓦斯太冷
)
.
連續火燄開關已撥到左
1. 補充瓦斯
2. 火燄調整
邊或左邊
通過逐步調整火燄調整開
關漸增加氣量再逐步重新
點燃的火炬調整
1. 補充瓦斯
2. 握在手掌
開關滑往右
中加溫.
圖一
點火
1.)使用時出氣口朝上以免損壞桌面.
“安全鎖”按鈕，同時用拇指順勢下滑觸動點火開關。這一
2.)按
動作會點燃烙鐵
3.)釋放
“安全鎖”按鈕，拇指維持下壓點火開關。將連續火燄開
關撥到右邊(圖二)確保不熄火.
Test Equipment Depot - 800.517.8431
- 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
PROKIT’S INDUSTRIES CO., LTD.
©2013 Copyright by Prokit’s Industries Co., Ltd(C). 2013001
Loading...