EchoLife HG8121H GPON Terminal
Quick Start
Safety Information
To use the device properly and safely, read the safety precautions carefully before using
the device and strictly observe these precautions when using the device.
Safety precautions:
Store devices and accessories in temperature –10°C to +35°C and relative
humidity 30%–85% RH for at most 9 months. If the ambient temperature or relative
humidity is overhigh or overlow, the device may be faulty.
Used only indoors. Do not lead metallic cables, such as network cables and
telephone lines outdoors.
Do not look directly into the optical port without eye protection.
Keep the device out of the reach of children as the components or accessories
may b e swallowed.
Install the device in strict compliance with the requirements of the supplier.
Reserve a space of at least 10 cm above and around the device for heat
dissipation. During the installation, keep the device away from electric appliances
that generate strong magnetic or electric fields, such as microwave ovens,
refrigerators, and mobile phones.
The described input voltage range should comply with the local power grid. For
example, the input voltage of the adapter is 200–240 V AC for European Union;
the input voltage of the adapter is 100–140 V AC for America.
If the power adapter is damaged and its internal circuit is exposed due to
manmade factors, do not touch the exposed circuit, which may bring safety risks.
Only power adapters delivered with the device can be used. Otherwise, the device
may be abnormal or unsecure.
Dry your hands before connecting or disconnecting cables. Stop the device and
switch off the power before connecting or disconnecting cables.
Do not place any object on the device, so that the device will not be damaged due
to overheating or deformation.
Prevent objects, such as metal, from entering the device through the heat
dissipation hole.
Switch off the power and disconnect all cables, i ncluding the power cable, optical
fiber, and network cable, during periods of lightning activities. The socket-outlet
shall be installed near the power adapter and shall be easily accessible. Before
use the power adapter, please check no damage on the adapter.
Do not lead the strength member of the optical fiber or other metal parts indoors.
Do not install telephone lines, network cables, power adapters or power adapter
cables outdoors. Adopting these measures will help prevent device damage and
bodily injuries which are especially prone during thunderstorms.
If an abnormality occurs, for example, liquid entering the device, smoke, unusual
sound, and smell, stop the device immediately, switch off the power, disconnect all
cables (such as the power cable, optical cable, and network cable) to the device,
and contact the authorized service center.
1
NOTE
Do not disassemble the device without permission. In the case of a device fault,
contact the authorized service center.
Dispose of the packing materials, expired batteries, and old or abandoned devices
in accordance to local laws and regulations (recycling them is strongl y
recommended).
Do not change the structure, safety design, or performance design of the device
without prior authorization.
The device should be installed and operated with a minimum distance of 20 cm
between the radiator and your body.
Fireproof precautions:
Keep the device away from large heat source equipment, bare flames, and
high-power devices, such as electric heaters, candles, and blow drier, to eliminate
safety risks.
If there are aged cabl es or power socket facilities on the power supply line to or
near the device, replace them in time to eliminate safety risks. The power supply
voltage of the device must meet the input voltage requirement.
Product Overview
Product Function
1 GE + 1 FE
HG8121H
1 POTS port
Wi-Fi access
Technical Specifications
Item Specifications
Dimensions (L x W x H)
Weight (including the power
adapter)
System power supply
Power adapter input
Maximum power consumption
Operating temperature 0ºC – +40ºC
Operating humidity 5%–95% RH (non-condensing)
156 mm x 125 mm x 28 mm (without an
external antenna)
less than 1000 g
See the nameplate on the device
See the nameplate on the adapter
≤ 12 W
If the appearance of the product in this document differs from the actual product, the actual
product prevails.
2
CAUTION
Installing the GPON Terminal
1. Do not install GPON terminals outdoors or on the outdoor cabinets.
2. GPON terminals can be mounted onto a wall or be placed on a workbench. Do not install
GPON terminals in other modes, such as the ceiling.
3. The terminal cannot be connected to other devices such as GPON terminals, switch and
router.
Mounting a GPON terminal on the desk
The figure below shows a GPON terminal that is horizontally placed on a desk.
Mounting a GPON terminal onto the wall
Step 1 Mark the positions of two holes used for mounting a GPON terminal,
ensure that the two holes have the same spacing as the two mounting
holes.
Step 2 Select a proper drill according to the outer diameter of the screws. Use a
hammer drill to drill the marked positions on the wall. Then clean the wall
and install two expansion bolts.
Step 3 Use a screwdriver to fasten the screws into the expansion bolts, leaving
the heads of the screws 3 mm over the wall. Then install the GPON
terminal to the screws.
3
Power socket
Phone
TV set
IP STB
PC
5
Wi-Fi terminal
7
6
1 2
3
4
Connecting Cables
4
NOTE
The type of the optical connector connected to the optical port in the wall is determined
mm.
1. Power switch 2. Power port 3. POTS port
4. Ethernet ports 5. Reset 6. WLAN switch
7. WPS switch 8. Optical port
Step 1 Use an optical fiber to connect the optical port on the ONT and the optical
port on the wall.
by practical conditions.
To ensure normal use of fibers, make sure that the fiber bend radius is larger than 30
Step 2 Use a network cable to connect the FE/GE port to a PC or the Ethernet
port on the IP STB.
Step 3 Use a phone line to connect the TEL port to a phone or fax machine.
Step 4 Use a power adapter to connect the POWER port to the power socket.
5
NOTE
NOTE
NOTE
NOTE
If you do not perform any operations after logging in to the system for five minutes, you
Change the initial password after logging in to the web page.
The preceding figure connects the power adapter as an example. When connecting the
backup battery unit, please see the usage guide to the backup battery for details.
Step 5 Press the ON/OFF power switch.
Step 6 Press the WLAN switch to enable the Wi-Fi access function. By default,
this function is enabled.
Step 7 Press the WPS switch to enable the WPS encryption function.
Before enabling the WPS encryption function of a GPON terminal, ensure that the
function is set in the system software in advance. After successful setting, press the
WPS switc h for the settings to take effect.
Logging in to the Web Configuration Window
Step 1 Set the IP address of the PC in the same subnet as the management IP
address of the GPON terminal.
You can find the default management IP address on the nameplate of the device.
Step 2 Enter the management IP address of the GPON terminal in the address
bar of Internet Explorer and press Enter. The login window is displayed.
Step 3 In the login window, select your preferred language, enter the user name
and password (printed on the nameplate of the device.), and click Login.
After the password is authenticated, the Web configuration window is
displayed.
will exit the system and the system automatically returns to the login interface.
The system will be locked if you input incorrect user name and password three
consecutive times. One minute later, it will be unlocked.
Configuring Wi-Fi Parameters
Step 1 Choose the WLAN tab and choose Basic Network Settings.
Step 2 In the pane, select the Enable WLAN option box. In the dialog box that is
displayed, set the basic Wi-Fi parameters, including the SSID,
authentication mode, and encryption mode.
6
NOTE
Electronic devices or components that produce RF noises. (Keep a distance of more
wireless network.
SSID: See the nameplate on the device. SSID indicates the name of a wireless
network searched by the Wi-Fi termi nal
WPA PreSharedKey: See the nameplate on the device. WPA PreSharedKey
indicates the authentication password for the Wi-Fi terminal to access a wireless
network.
Step 3 Click Apply.
HG8121H supporting Wi-Fi, a wireless network coverage is subject to the number,
thickness, and positions of walls, material, ceilings, or other objects that radio signals
traverse. Besides, material type and background radio frequency (RF) noise also affect the
coverage of a wireless network. You can maximize the coverage of a wireless network
using the following methods:
1.
Decrease the number of walls and ceilings between HG8121H and other
network devices.
Each wall or ceiling reduces the coverage of a wireless network by 1 to 30 meters.
Install HG8121H at a proper place to avoid walls or ceilings whenever possible.
2.
Observe the straight line rule when installing network devices.
The distance for which signals have to traverse at a 45° corner of two 0.5 meter-thick
walls reaches approximately 1 meter. Therefore, place devices at places where
signals can directly traverse walls or ceilings.
3.
Note the impact of building materials on the wireless network coverage.
A metal door or aluminum wall may limit the coverage of a wireless network. Install
access points, wireless routers, and computers, so signals can traverse walls or open
passageways. Materials and objects such as FRP products, metal products, insulative
walls, filing cabinets, bricks, and concrete weaken radio signals.
4.
When connecting HG8121H to a wireless network, keep it far from the
following devices:
than 2 meters between such a device andHG8121H.)
2.4 GHz wireless mobile phones and X-10 devices (such as microwave ovens, home
security systems, blue-tooth devices, and refrigerators) greatly weaken or even
eliminate wireless signals. Even when a 2.4 GHz wireless mobile phone is not
connected to a wireless network, the phone base still sends signals that interfere the
5.
Do not use the HG8121H in public scenarios, such as cafe and store,
because it is designed for only residential applications.
6.
You are advised to connect a maximum of 10 terminals through Wi-Fi for
user experience.
7
LED
Status
Description
POWER
Green: Steady on
The device is powered on.
Off
PON
See Table 1-2
LOS
See Table 1-2
Steady on
The terminal is registered with the softswitch
Blinking
Service flows are transmitted.
registered to the softswitch.
state.
Blinking
Data is being transmitted on the Ethernet
port.
Off
The Ethernet connection is not set up.
Steady on
The WLAN function is enabled.
Blinking
Data is being transmitted on the W LAN port.
Off
The WLAN function is disabled.
WPS
Steady on
The WPS function is enabled.
Blinking
A Wi-Fi terminal is accessing the system.
Off
The WPS function is disabled.
No.
Status
PON
LOS
second
Indicator Description
Table 1-1 Indicator status description 1
The power supply is cut off.
TEL
Off The terminal is not powered on or fails to be
GE/FE Steady on The Ethernet connection is in the normal
WLAN
Table 1-2 Indicator status description 2
Status
1 Off
Blinks
twice a
2
but no service flows are transmitted.
Description
The GPON terminal i s prohibited by the
upper-layer device, contact the service
Steady on
Off
provider for help.
The GPON terminal attempts to set up a
connection with its upper-layer device.
8
3
4
5
6
Steady on
Off
Blinks
twice a
second
Blinks
once two
seconds
Off
Blinks
once two
seconds
Blinks
once two
seconds
Blinks
once two
seconds
A connection is set up between the
GPON terminal and its upper-layer
device.
The GPON terminal i s not connected to
optical fibers or does not receive optical
signals.
The GPON terminal i s a rogue terminal,
contact the service provider for help.
The hardware is faulty.
Disposal and recycling information
The crossed-out wheeled-bin symbol on your product, battery, literature or
packaging reminds you that all electronic products and batteries must be
taken to separate waste collection points at the end of their working lives; they
must not be disposed of in the normal waste stream with household garbage.
designated collection point or service for separate recycling of waste electrical and
electronic equipment (WEEE) and batteries according to local laws.
Proper collection and recycling of your equipment helps ensure electrical and electronic
equipment (EEE) waste is recycled in a manner that conserves valuable materials and
protects human health and the environment, improper handling, accidental breakage,
damage, and/or improper recycling at the end of its life may be harmful for health and
environment. For more information about where and how to drop off your EEE waste,
please contact your local authorities, retailer or household waste disposal service or visit
the website www.huawei.com/en/product-certification.
It is the responsibility of the user to dispose of the equipment using a
Reduction of hazardous substances
This device and any electrical accessories are compliant with local applicable rules on the
restriction of the use of certain hazardous substances in electrical and electronic
equipment, such as EU REACH, RoHS and Batteries (where included) regulations, etc.
For declarations of conformity about REACH and RoHS, please visit our web site
www.huawei.com/en/product-certification.
9
FAQ
The LOS indicator blinks.
If the LOS indicator blinks once two seconds, check whether the pigtail fiber is
properly connected and the connector is clean.
If the GPON terminal blinks twice a second, contact the service provider for
help.
The PON indicator is off.
Check whether the OPTICAL port and optical fiber is properly connected.
The GPON terminal fails to register with the upper-layer device. Contact the
service provider for help.
The phone does not ring upon an incoming call but communication
is in normal state when the phone is in off-hook state.
The GPON terminal provides a maximum of 60 V AC ringing current voltage.
Check whether the ringing current voltage of the phone is higher than 60 V AC.
If it is higher than 60 V AC, replace it with another phone.
How to reset the GPON terminal?
Press Reset by using a needle-t ype object.
How can I restore factory defaults?
Press Reset by using a needle-t ype object for longer than 10s to restore
factory defaults and reset the GPON terminal. If the indicator is off and then is
lit, the system restarts successfully.
10
11
PASS
Qualification Card
Copyright © Huawei Technologies Co., Ltd. 2019. All
rights reserved.
No part of this document may be reproduced or transmitted in any form or by any
means without prior written consent of Huawei Technologies Co., Ltd.
31509265_02
Warranty Card
Thank you for choosing Huawei Technologies Co., Ltd. To get better services,
please read this warranty card carefully, fill in the required information, and
preserve this card in good condition.
User Information
Personal or
Company's full name:
Address/Postal Code:
T
elephone:
Email:
Product Type:
Product Serial Number:
Purchase Date:
In
voice Number:
Dealer's Name:
Dealer's Address:
Deale
r's T
Dealer's Seal
elephone:
Preserve well. No reissue.
Limited Warranty
Subject to the exclusions contained below, Huawei Technologies Co., Ltd. (Huawei
for short) warrants its access terminals ("Products") to be free from defects in
materials and workmanship under normal consumer usage for one year from
the date of purchase of the product ("Warranty period"). During the warranty
period, a Huawei authorized service partner shall remedy defects in materials and
workmanship free of charge.
Special Notice:
1. The warranty card shall be applicable only after being stamped by the dealer.
2. The warranty card must be preserved in good condition and free of any scratch or
alteration.
3. To claim such service for defects that are not included in the following exclusion
terms, the warranty card and the invoice that records that product serial number
shall be presented to a Huawei authorized service partner.
Exclusion:
In any o f the following cases, the warranty card becomes unenforceable or
inapplicable without pri or notice:
1. The defects are caused by improper handling in transportation and assembly.
2. The defects are caused by the fact that the product is dismantled or altered by
anyone that is not from a Huawei authorized service partner.
3. The defects are caused by the fact that the product is used in a harsh environment
that is not suitable for the operation of the product.
4. The defects are caused by any force majeure including but not limited to fire,
earthquake, lightning, and tsunami.
5. The defects are caused by the fact that the product is used or handled incorrectly,
roughly or not as instructed in the applicable User Guide.
6. The normal wear and tear, including but not limited to the normal wear and tear of
the shell and the power module, shall not be covered by the limited warranty.
7. The warrant y card is altered or illegible, or the product serial number recorded on
the warranty card is inconsistent with the actual one imprinted or labeled on the
product.
In any case that is not covered by this limited warranty or should the warranty
expire, Huawei shall charge for the service(s) claimed for the products if the
product is still remediable. Huawei reserves all rights to interpret this limited
warranty.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Loading...