Page 1
Instruction Manual
Model PWE-1800
93567-DP
Customer Help Line
1-800-673-1558
WARNING: To reduce the risk of injury, the user must read and understand the instructions
before using this product.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Page 2
PackaGe content:
1. Power washer unit
2. Manual
3. Nozzle cleaning wire (may be taped
to the manual)
4. High pressure hose
5. Spray gun holder
6. Nozzle tray
7. Screws (1 for nozzle tray)
8. High/Low nozzle
9. Turbo Nozzle
10. Spray gun (10A shows trigger lock
button)
11. Power Washer Quick Connect
Filter (clear) (Connect to Power Washer
Unit/with lter inside)
12. Garden Hose Adapter (Connect to
Garden Hose)
Quick Start Guide
Hose reel
storage only
1
5
4
6
11
12
3
2
7
8
9
10
10A
Phillips screwdriver required for assembly
(not provided)
1. Slide Gun holder on side.
2. Snap in place and screw lance
tray.
3. Swivel bottom cord hook right or left to easily
remove the power cord.
Push to
lock
1
2
2
Push to
unlock
1
4. Attach high pressure hose to
power washer.
2
5. Attach high pressure hose to
spray gun.
Trigger Trigger
6. Push on right side of spray gun to lock trigger.
Push on the left side of the spray gun to unlock
trigger. Always make sure that spray gun is
locked when not in use.
Page 3
7. Connect lances to spray gun,
insert lance into spray gun,
push together and at the same
time twist clockwise to lock in
place. Removing push together
and twist counterclockwise
then pull apart.
High pressure setting
Fan
Spray
Pencil Stream
IN position
IN position
High pressure
setting
Low pressure setting
Pencil Stream
OUT position
OUT position
Low pressure
setting
8. The adjustable spray nozzle
had has two (2) positions: •IN
position for high pressure
spray. Designed to use
for cleaning and allowing
spray to be adjusted. • OUT
position for low pressure
spray for detergent function.
Spray needs to be set with
fan blades in the “pencil
stream” position to assure the
detergent is not restricted.
(GHA)
9. Fill detergent tank (page
11). Do NOT use thick
detergent as it can clog the
power washer.
13. Snap the GHA onto the QC
adapter. To remove pull
back on the collar and pull
o.
10. Pull clear siphoning tube
through cap so it will
draw detergent from
bottom of tank.
QC - Clear
Adapter
Garden Hose
Adapter (GHA)
14. Clear QC adapter attaches
to power washer, GHA
attaches to garden hose.
11. Clear QC lter attaches
to the power washer.
15. Plug machine into a
grounded outlet, push
reset button.
12. Attach GHA to the end of
the garden hose.
16. Turn on water.
OFF/0
ON/I
OFF/0
17. Switch OFF and ON
positions.
ON/I
3
Page 4
tabLe of contentS
Quick Start.............................................................................2
Specications.......................................................................4
Limited Warranty.................................................................4
Introduction..........................................................................5
Safeguard, Warnings & Safety Tips................................5
GFCI..........................................................................................6
Package Content..................................................................7
Unpacking & Assembly......................................................8
Operating Instructions........................................................13
How to Clean..........................................................................14
Operating Tips and Maintenance .................................. 14
Storage.....................................................................................16
Pump Saver............................................................................ 17
Replacement Parts................................................................18
Troubleshooting and FAQ..................................................19
SPecificationS
Model Max PSI (lbs/sq in) Max GPM (gal/
min)
PWE-1800 1,800 1.3 For cold
Max Temp Volts Amps Weight (lbs)
120 13 26
water only
Limited Warranty
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product (including
the spray gun, high pressure hose, accessories and parts purchased separately) are free from defects in
material and workmanship for a period of one year from the date of purchase. THIS LIMITED ONE YEAR
WARRANTY APPLIES ONLY TO PRODUCTS USED IN CONSUMER APPLICATIONS AND IS VOID IN RENTAL OR
COMMERCIAL APPLICATIONS. Under normal use and maintenance from date of purchase, ECHO agrees
to repair or replace at ECHO’s discretion, any defective product free of charge. THIS LIMITED WARRANTY IS
EXTENDED TO THE ORIGINAL PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS.
Repair parts and accessories replaced under this warranty are warranted only for the balance of the original
warranty period. Reasonable care must be used in conformity with operation and maintenance instructions
in the owner’s manual and quick start guide. Any damage caused by failure to follow these instructions will
void this warranty. All parts or products replaced under warranty become the property of ECHO, Inc.
To ensure trouble free warranty coverage it is important that you register your ECHO product on-line at
WWW.ECHO-USA.COM Registering your product conrms your warranty coverage and provides a direct
link if we nd it necessary to contact you.
Should a product diculty occur within the warranty period, you must, at your expense, deliver or ship your
ECHO unit to an authorized ECHO servicing location (normally the place where you purchased the unit) and
arrange for pick-up or return of your unit after the repairs have been made. It is the owner’s responsibility to
provide a dated proof of purchase (receipt) to an authorized ECHO servicing location for warranty service.
Should you require assistance or have questions concerning ECHO’s Warranty policy, you can contact our
Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHOUSA.COM or E-Mail us at support@echo-usa.com.
This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of
FITNESS FOR A PARTICULAR PURPOSE OR USE and any implied warranty of MERCHANTABILITY otherwise
applicable to this product. ECHO and its aliated companies shall not be liable for any special incidental
or consequential damage, including lost prots. There are no warranties extended other than as provided
herein. This limited warranty may be modied only by ECHO. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so you may also have other specic legal
rights which vary from state to state. This limited warranty is given by ECHO Incorporated, 400 Oakwood Rd.,
Lake Zurich, IL 60047.
4
Page 5
introduction
Congratulations on the purchase of your ECHO POWER WASHER!
Your ECHO POWER WASHER is a power tool in every sense of the word that may be used outside your house
and in. It is one of the nest most powerful home-use power washers in the marketplace today.
Please familiarize yourself with the following assembly, operating and safety information. Read this manual
before using the power washer. Failure to follow these instructions could cause personal injury, property
damage, or both. Save this manual for other users to read prior to using the power washer.
If you have any questions about or problems with your power washer please call our toll-free number 1-800673-1558 and talk with our Consumer Support Team. We are available to talk with you Monday through Friday from 8 a.m. to 4:30 p.m. Central Standard Time (CST). We can help you with questions regarding operation, warranty, replacement or optional parts, or e-mail us at support@echo-usa.com .
SafeGuardS, WarninGS & Safety tiPS
• To avoid personal injury and/or damage to
property and to maximize your power washing
experience, carefully follow all of the safety
tips, instructions, warnings and safeguards and
become familiar with all of the controls. Be sure
you know how to quickly bleed off the pressure
from all parts of your power washer, and how to
turn off the power washer .
• This power washer conforms to CSA US and other
safety and consumer standards. Do not modify or
rebuild any part of your power washer.
• Do not use your power washer when you are
under the inuence of alcohol or drugs. Use this
power tool carefully and only when you are alert .
• Watch your balance and footing while using
your power washer. Surfaces become slippery
when wet and are extra slippery when using a
detergent or cleaner.
• Never operate the power washer in bare feet,
sandals, or open-toed shoes.
• When using the power washer near children
make sure they are closely supervised by an adult
to avoid injury. Never let a child use the power
washer.
• Keep ngers, hands, feet and any part of your
body clear of the stream of high pressure water.
The powerful spray can cause blindness or blast
holes in the skin. It can break a window if you are
too close when you pull the trigger on the spray
gun .
• Always wear eye protection to prevent injury to
eyes when operating the power washer.
• To avoid mishaps or injury, always use the trigger
safety lock when not using the power washer
even if the spraying stops for a moment.
• The power washer is equipped with a Ground
Fault Circuit Interrupter (GFCI) which greatly
reduces the chance of electric shock while the
unit is in use.
• Point the spray gun in a safe direction when
beginning a power washing session.
• When rst using the spray gun, hold the spray
gun and lance with two hands when pulling the
trigger until you get used to the “kick back” from
the spray gun (one hand to pull the trigger and
the other to stabilize the gun assembly).
• When you press the power switch to turn off the
power washer, water pressure may remain in the
system. To discharge the pressure, point the spray
gun in a safe direction and pull the trigger.
5
Page 6
• Never spray ammable liquids.
• Never use the power washer in areas that contain
combustible dust, liquids or vapors.
• Avoid contact of the pressure hose with sharp
objects and examine the hose regularly. Replace
if damaged. Due to the high pressure involved, it
cannot be repaired if cut of damaged.
• Never use a water supply to your power washer
that exceeds 150 psi maximum.
• Never disconnect the high pressure hose
from the power washer while the system is
pressurized.
• Never permanently engage the trigger
mechanisms on the spray gun.
• Only use detergent specically formulated for
power washers and follow instructions on the
detergent’s label. Power washer detergents are
also available at your local hardware store.
• Protect eyes, lungs, and skin from exposure to
detergent. Dish or laundry soap is too thick and
will clog the nozzle of your detergent tank.
• IMPORTANT: Store the power washer indoors to
prevent the water in the unit from expanding
under freezing conditions. When the water
freezes and expands, your power washer will be
damaged and become inoperable. Or, if storing
outdoors, it is recommended you use Pump Saver.
• Never use hot water with your power washer.
It will overheat and damage the high pressure
pump.
• Never leave the power washer unattended while
it is powered “on”.
• Never operate the power washer unless
all components are properly and securely
connected.
• Never allow the power washer pump to run for
more than one minute, after you have turned off
the water supply. This can cause the motor and
pump to overheat and fail.
• Never use lances or other parts that have not
been supplied with your power washer.
• Never use an extension power cord since
it defeats the effectiveness of the GFCI and
increases the chance of electrocuting the
operator.
• Never spray any electrical outlet with your power
washer.
• Inspect the power cord before using. Do not use
it if it is damaged.
• Always turn the water supply “on ” before turning
the power washer power to “on”. Running the
pump dry will cause damage to the internal
components.
Gfci
Ground Fault Circuit Interrupter Protection:
This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plugs of the
power-supply cord. This device provides additional protection from the risk of electric shock. Should
replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI
protection.
In a double-insulated product, two systems of insulation are provided instead of grounding. Grounding
means are not provided for a double insulated product, nor should grounding means be added to the
product. Servicing a double-insulated product requires extreme care and knowledge of the system, and
should only be done by qualied service personnel.
Replacement parts for a double-insulated product must be identical to the original parts.
A double-insulated product is marked with the words “Double Insulated”. Product may also be marked with
a symbol.
6
Page 7
PackaGe content
1. Power washer unit
2. Manual
3. Nozzle cleaning wire (may be taped
to the manual)
4. High pressure hose
5. Spray gun holder
6. Nozzle tray
7. Screws (1 for nozzle tray)
8. High/Low nozzle
9. Turbo Nozzle
10. Spray gun (10A shows trigger lock
button)
11. Power Washer Quick Connect
Filter (clear) (Connect to Power Washer
Unit/with lter inside)
12. Garden Hose Adapter (Connect to
Garden Hose)
Note - tool(s)
required for
assembly Phillips
Screwdriver:
Hose reel for
storage only
1
5
4
6
11
12
3
2
7
8
9
10
10A
7
Page 8
unPackinG & aSSembLy
• After unpacking the ECHO POWER WASHER, lay out parts and accessories. Familiarize yourself with the
parts in the package by comparing them to those listed on the “PACKAGE CONTENTS” page.
• The ECHO POWER WASHER requires some minor assembly. You’ll need a Phillips screwdriver to install the
high pressure hose hook and the nozzle tray.
NOTE: Some parts may or may not be already assembled.
• High pressure hose is stored on the hose reel. With the front of the power washer facing towards you, insert
the un-threaded end of the high pressure hose into the square hole on the inner reel and begin turning the
handle away from you. When nished winding, push the handle in to lock it in place.
NOTE: The hose reel is only for storing the high pressure hose. The hose must be completely removed from
the hose reel each time you use the power washer.
• Slide the spray gun holder onto the left side of the washer when facing it. This does not require any screws.
(Fig. 1)
Fig. 1
Fig. 2
• Slip tab into slot and screw the nozzle tray on the bottom portion of the unit. (Fig. 2) When placing the gun
with the lance attached the nozzle will rest in this tray.
• Easily remove the power cord from side of unit by swiveling the bottom cord hook to the right or left until
it faces up. The power cord then can be easily slid o of the side of the power washer unit. (Fig. 3)
• Swivel cord hook
back down when
ready to wrap the
cord back into place
for storage.
Fig. 3
8
Page 9
High Pressure Hose
• Screw the high pressure hose (clockwise) on the left of the unit at the bottom (Fig. 4). Pull back the collar
and insert o-ring post into the water outlet far enough so the collar can thread onto the outlet threads until
hand tight. Do not use pliers or vice grips to tighten. If it takes fewer than six or so turns you have not properly tightened the high pressure hose tting. It is easier to position the power washer in front of you so to
ensure that the threads are started correctly. Failure to properly tighten the high pressure hose will result in
the hose slipping or popping o immediately upon turning the unit on. Do not worry about damage if this
occurs - just reinstall and take extra care at screwing on the high pressure hose tting.
Fig. 4
Fig. 5
• Connect the other end of the high pressure hose to the spray gun by inserting the brass metal tip of the
high pressure hose into the tting just ahead of the trigger guard. It will lock into the spray gun with a
“click” (Fig. 5). Conrm the hose is locked into the spray gun by pulling slightly on the hose. The hose is now
securely attached to the spray gun.
• To release the hose from the spray gun, press the button on the underside of the gun toward the trigger
guard. The hose will slide out from the connection (Fig. 6).
Fig. 6
9
Page 10
Spray Gun
• To lock the trigger of the spray gun aim the gun away from you and push the lock button from right to left,
(Fig. 7), after doing so, squeeze or pull the trigger to make sure it is locked and will not move. Always leave
lock button in lock position when not in use. This ensures the gun is in “safe” mode until it is ready for use.
Push to
lock
1
2
Trigger
2
Trigger
Push to
unlock
1
Fig. 7
Lance
• While the spray gun is in the locked position, insert the high/low nozzle lance or turbo nozzle into the end
of the spray gun by inserting and pushing together turning clockwise simultaneously. To remove push
together and turn counter clockwise (Fig. 8).
Remember to always push the safety lock button to lock the trigger when changing lances, to ensure that
they do not accidentally eject with force during removal.
• When using the turbo lance, make sure the turbo nozzle is screwed on tight at the end of the lance, each
time you use it. The Turbo lance is designed for high impact cleaning. Only use on hard surfaces such as
driveways, cement surfaces, patio bricks, etc.
Fig. 8
Fig. 9
Always test a small area to avoid chance of damaging the surface. (Fig. 9).
• Using High/Low Nozzle. High Pressure spray is used for cleaning and Low Pressure spray activates the
detergent function.
10
Page 11
• The adjustable spray nozzle had has two (2) positions (Fig. 10):
OUT position
OUT position
Low pressure
setting
Fig.10
High pressure setting
Fan
Spray
Pencil Spray
IN position
IN position
High pressure
setting
Low pressure setting
Pencil Spray
IN position for high pressure spray. Twist the nozzle counterclockwise until it stops and gap is closed.
OUT position for low pressure spray for detergent function. Twist the nozzle clockwise until it stops and
gap is open.
• When using the High Pressure setting twist the nozzle head clockwise or counterclockwise to achieve the
stream desired.
• When using the Low Pressure setting twist the nozzle head clockwise to open the fan blades all the way.
IMPORTANT NOTE: When applying detergent using low pressure spray, the variable spray head must be
set for the “Pencil Stream”. This is when the metal blades in front of the nozzle is wide open so the detergent
spray is not constricted.
• When using the detergent, ll it with a properly formulated detergent or cleaner with water ratio according to instructions on the container (Fig. 11). The detergent tank comes with a straw which is tted into the
screw-on top. If you don’t see the straw, look inside the tank and attach it to the screw-on top (Fig. 12).
Fig.11 Fig.12
• When removing the detergent tank remove lid and place nger in tank lifting up while pulling tank out.
11
Page 12
Garden Hose Adapter
• Install the garden hose adapter (GHA) and quick connect lter. It is made up of two separate pieces. (1) A
clear plastic adapter with a screen lter (about 3 inches long) and (2) collar attachment (Fig. 13).
QC - Clear
Adapter
Garden Hose
Adapter (GHA)
Fig. 13 Fig. 14
(GHA)
• Attach the garden hose adapter to the end of the garden hose (Fig. 14).
• First, remove the plastic shipping cover on the water inlet on the front of the power washer on the right
side. Attach the clear quick connect lter to the power washer (Fig. 15) hand tight is ne. Slide the garden
hose adapter collar onto the clear adapter (Fig. 16), it will “click” into place.
Fig. 15
Fig. 16
• The water is now connected to your power washer. Turn on water.
• To remove the water hose, simply pull back on the blue collar and it will slide o the clear adapter.
Note: this can be done at any time. Water will not come out of the garden hose as the collar has a water stop
check valve. Water will only ow from the garden hose when it is connected to the clear adapter.
• You have now completed the assembly of your ECHO POWER WASHER and are now ready to begin using
your electric power washer. Read and observe all safety instructions.
12
Page 13
oPeratinG inStructionS
*!Turn on the water supply at the faucet.!* (Fig. 17)
OFF/0
ON/I
Fig. 17 Fig. 18
OFF/0
ON/I
Powering Up
• Make sure the “ON/OFF” switch is in the “OFF” position. The power switch has international symbols for ‘on’
and ‘o’: On (|) O (O), (Fig. 18).
• Unwind the power cord completely and plug the GFCI into a grounded 120 volt outlet. Press the ‘reset’
button on the GFCI box (Fig. 19). The indicator window should show a green color. This must be done each
time the unit is plugged in.
Push to
unlock
1
Fig. 19
Push to
lock
Fig. 20
1
2
Trigger Trigger
2
• Release the safety lock button on the spray gun by pressing the safety lock button from left to right (Fig.
20). While pointing the spray gun in a safe direction, squeeze the trigger on the spray gun until there is a
steady stream of water, letting the water and air out of the hose.
• Turn the power switch to the ‘ON’ (|) position. The unit will turn on for 1 - 2 seconds and shut o, this is a
normal function of the (TSS) auto start feature. Squeeze the spray gun trigger to begin pressure washing.
• Squeezing rapidly will cause the (TSS) feature to miss an on/o cycle that may prevent from turning on
while squeezing trigger after rapid squeezing. Use slow deliberate trigger pulls to avoid such symptoms.
13
Page 14
HoW to cLean
Cleaning nozzles
• A clogged or partially clogged nozzle can cause signicant reduction of water pressure coming out of the
nozzle and/or cause the unit to pulsate while spraying.
• Turn o the unit
• Turn o the water supply to the unit
• Relieve any pressure trapped in the hose by squeezing the trigger 2-3 times, and then lock the spray gun by
pushing the lock button from left to right.
• The screen inside the clear adapter should be cleaned periodically. Insert a pen or pencil in small hole at the
end of the adapter. The screen lter will slide out (Fig. 21). Rinse it with clean water, and then place it back
in the adapter.
Fig. 21
• Using the nozzle tip cleaner provided (or an unfolded paper clip), insert the wire into the nozzle hole and
move back and forth until debris is dislodged (Fig. 22). Back ush water through the nozzles using garden
hose and highest pressure available (either standard water nozzle or use your thumb over the nozzle to
create water pressure for back ush).
Fig. 22
oPeratinG tiPS and maintenance
• If you hear the motor run intermittently when the trigger is not being squeezed, that is normal. The pump
is priming itself so it is ready to operate when the trigger is squeezed. Turn o the power washer if not
being used after ve minutes.
• The o-rings on the bayonet end of the adjustable lance should be cleaned regularly and lubricated with
non-water soluble grease such as petroleum jelly.
• Keep the nozzle cleaning wire, which is taped to this manual, for use in unclogging the lance nozzle. If you
lose the cleaning wire an unbent paper clip works ne.
• NOTICE: Always make sure the water inlet line (garden hose) is not kinked or restricted from providing
sucient water ow. Insucient water ow may damage the pressure washer pump.
How to Avoid Damaging Surfaces
• Damage to surfaces being cleaned occurs because the impact force of the water pressure exceeds the
durability of the surface. Bare wood can be penetrated; paint can be peeled o, etc.
14
Page 15
You can vary the force of your power washer by controlling:
a. the angle of the surface being cleaned
b. the distance of the nozzle from the surface being cleaned
• Never use a narrow high pressure stream of water or the turbo lance on soft surfaces susceptible to
damage.
• Use the high/low nozzle lance when cleaning windows. Be sure to adjust the nozzle to low spray and place
the nozzle approximately four to ve feet away from the window with the nozzle at forty ve degree angle.
Squeeze the trigger and vary the spray pattern and angle until optimum cleaning eciency is achieved
(Fig. 23).
Twist to adjust spray
Twist to adjust pressure
Spray
Pressure
Fig. 23
Detergent Injector/Storage
• Typically, there are dierent power washer detergents for specic applications, such as auto, motorcycle,
boat and universal. Hardware stores or home centers also have power washer detergents for dierent
cleaning projects. The cleaning solution should be the consistency of water in order to prevent clogging
your detergent tank and nozzle.
• This system applies detergent under low pressure. The cleaning power of the detergents is enhanced when
applied with low pressure; and time is allowed to break down the dirt and grime. The combination of low
pressure and chemical action is very eective and can be better than scrubbing if applied properly. Always
spray detergent on a dry surface, do not pre-soak area. Wetting the surface rst dilutes the detergent and
reduces its cleaning ability. Do not allow detergent to dry on surface. On vertical surfaces being cleaned,
apply detergent to lower surfaces and work your way up to prevent detergent from causing streaks in the
dirt and grime. Rinse detergent by pressure washing from bottom up for same reason.
• If a stain is particularly tough, it may be necessary to reapply the detergent and use a bristled brush to
scrub the stain. Subsequent power washing after brushing should successfully complete your cleaning job.
15
Page 16
StoraGe
• DO NOT store the power washer where it is exposed to freezing temperatures unless you use Pump
Saver. It is recommended that you use Pump Saver for storing in freezing temperatures. Freezing will
damage the pump unless Pump Saver is added to the power washer.
• Remove lance from the gun and place in the accessory holder. Place the gun in the accessory holder one
the side. Lances are placed into any of the slots in the back of the unit. Make sure to discard any remaining
detergent from the bottle. Flush the bottle and nozzle head with fresh water to prevent clogging.
• When your pressure washing session has been completed, turn o the power switch located on the front of
the power washer. Unplug the power cord from the outlet. Turn o the water supply. Pull the trigger on the
spray gun 2-3 times to drain out the excess water and to release any remaining water pressure. Disconnect
the garden hose adapter from the water inlet. Do not allow the power washer to run with no water owing
through it.
• Remove detergent tank and clean completely. Residual chemical will stick to the container and can cause
the detergent injector to clock and not function properly.
• Remove high pressure hose from spray gun and unscrew the other end of the high pressure hose from the
power washer.
• Wrap the power cord around the L-shaped tabs on the right side of the machine when facing it.
• The pressure hose is stored on the hose hook located on the back of the handle.
If not using or if storing your power washer for more than one month, run Pump Saver through it.
See the section on Pump Saver for more information.
16
Page 17
PumP Saver
Pump Saver is a product that protects and prolongs the life of the pump. This will keep the internal
parts of the pump lubricated and protected from freezing while being stored in ALL climates. It also
assists with protection from internal corrosion.
Pump Saver Instructions
Follow the previous storage instructions for your power washer. To prevent staining, protect the surface
under the power washer from any excess uid. Wear eye protection when using this product.
1. Turn o your power washer.
2. Disconnect garden hose.
3. Shake the bottle well before connecting to the power washer.
4. Screw the garden hose adapter to the Pump Saver Bottle.
5. Click onto pump inlet (clear quick connect lter).
6. Turn the valve on the bottle to the open position.
7. Turn the power washer on. Turn the power washer o as soon as the Pump Saver uid begins to exit the
water outlet - nozzle.
8. Turn the valve on the bottle to the o position and remove the Pump Saver bottle valve assembly from
the power washer.
17
Page 18
rePLacement PartS
1.
18.
2.
13.
19.
5.
14.
15.
17.
16.
4.
3.
6.
8.
12.
7.
REF # KIT DESCRIPTION REF # KIT DESCRIPTION
1 HANDLE ASSEMBLY 11 GARDEN HOSE ADAPTER
2 HOSE REEL ASSEMBLY 12 PRESSURE WASHER Q/C FILTER
3 WHEEL ASSEMBLY W/ GUARD 13 ON/OFF SWITCH
4 DETERGENT TANK 14 LANCE HOLDER
5 GFCI 15 NOZZLE TRAY
6 EXTENSION CORD HOOK 16 ACCESSORY BRACKET
7 HOSE, 20’ 17 REAR COVER
8 SPRAY GUN ASSEMBLY 18 PUMP MOTOR ASSEMBLY
9 HIGH/LOW LANCE/NOZZLE 19 FRONT COVER
10 TURBO LANCE/NOZZLE
11.
9.
10.
For replacement parts ordering, please visit www.echo-usa.com
18
Page 19
troubLeSHootinG and faQS
Unit will not turn on. Make sure the power washer is in the “OFF” position. Plug in the electrical cord to a
grounded 120 volt outlet (no electrical extension cord should be used). If the electrical
cord will not plug into your outlet, your electrical outlet is not properly grounded and
should not be used. Use another electrical outlet. Press the reset button on GFCI power
box. If the color of green is not visible in the little window on the GFCI, unplug and plug
in again. Press reset, and look for the green color in the window, this should remain green
in color. If the color is staying green, turn the power switch on the power washer to “ON”.
Squeeze the trigger on the spray gun and try again.
If this did not correct the problem, try plugging into another electrical outlet and repeat
the above procedure. If it is still not working, call Customer Service at 1-800-673-1558.
The high pressure (HP)
hose will not connect /
stay connected to the
spray gun. Is this a spray
gun problem?
The unit is running but
there is not water ow.
Why is water leaking
where the high pressure
hose connects to the
spray gun?
I can’t remove the lance
from the spray gun. What
should I do?
The power washer turns
on for 2 seconds, shuts
o, and will not turn back
on. Do I have a defective
unit?
In most cases, the spray gun is not the problem. The problem is the rubber sleeve
covering the tting at the end of the high pressure hose. It has likely slipped up toward
the metal tip. The x: wiggle, twist and/or pull the rubber sleeve down until the entire
tip is visible plus an 1/8” of the metal tting below the tip. Now try to insert the hose
tip into the spray gun. It should “click” into place and will not come out until the hose is
released by pushing in the lever on the underside of the gun. You may cut away the end
of the sleeve with a sharp knife if unable to move the sleeve down. Be careful not to cut
or puncture the hose.
Check the water source. Unclog the nozzle on the lance. (See nozzle cleaning instructions
under “Cleaning nozzles”.) Or take o the lance and just spray out of the spray gun. This
will indicate if the problem is with the lance.
Make sure there is an o-ring at the end of the metal tip of the high pressure hose. If no
o-ring is present, the connection between the hose and spray gun will leak.
All lances and the detergent tank are attached and removed from the spray gun in the
same manner. Insert the quick-release end of the lance/detergent tank into the spray
gun. Press the spray gun and lance together (about a 1/8”) and turn clockwise. The lance
will lock in place. Remove the lance by reversing this procedure. Press the spray gun and
lance together and turn counter clockwise. The lance will slide out. Or, hold the spray
gun and lance in an upright position with the nozzle end on the oor. Push the whole
assembly straight down to loosen the connection, and then follow the removal process
again. You may also spray soapy water or a lubricant in the area where the lance connects
to the spray gun.
It sounds like your power washer is working just ne. When the water is connected,
the accessories are assembled properly, and the power switch is turned on, the power
washer may turn on for 1 - 2 seconds to prime the pump. It automatically shuts o and
waits for the spray gun trigger to be pressed. When the trigger is pressed, water starts
owing through the pump. The water sensor in the pump “senses” the moving water
and automatically turns the power washer on. Or, turn the power switch to o, hold in
the trigger on the spray gun, so that you have a steady stream of water. While you are
holding the trigger open on the spray gun, at the same time, turn the power switch on.
19
Page 20
Model PWE-1800
W18000001001 - W18000999999
ECHO INCORPORATED
400 Oakwood Road
Lake Zurich, IL 60047
1-800-673-1558
www.echo-usa.com
E-Mail: support@echo-usa.com
Customer Help Line
1-800-673-1558
Loading...