Power Edger
Operator's Manual
MODEL PE-265
X7502024200
W ARNING
Read rules for safe operation and instructions carefully. ECHO provides an Operator's
Manual and a Safety Manual. Both must be read and understood for proper and safe
operation.
X750010170
04/07
2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-jobdependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operations tips and SAFETY messages.
THE OPERATOR'S MANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. Contains specifications and information for
operation, starting, stopping, maintenance, storage, and assembly
specific to this product.
THE SAFETY MANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. Explains possible hazards involved with the
use of Edgers and the measures you should take to make their use safer.
TABLE OF CONTENTS
Introduction ...............................................................2
- The Operator's Manual ....................................... 2
- The Safety Manual .............................................2
Safety ......................................................................... 3
- Manual Safety Symbols and Important
Information..........................................................3
- International Symbols ......................................... 3
- Personal Condition and Safety Equipment..........4
- Equipment ...........................................................6
Emission Control........................................................6
Description ................................................................ 7
Contents ....................................................................9
Assembly ................................................................... 9
- Drive Shaft/Power Head ...................................... 9
- Throttle Linkage and Ignition Leads ................. 10
- Front Handle .................................................... 11
Operation ................................................................. 11
- Fuel ................................................................... 11
- Starting Cold Engine ......................................... 13
- Starting Warm Engine ....................................... 14
- Stopping Engine................................................ 1 4
- Operating Techniques....................................... 15
Copyright© 2007 By Echo, Incorporated
All Rights Reserved.
Maintenance ............................................................ 16
- Skill Levels ........................................................ 16
- Maintenance Intervals ......................................16
- Air Filter ............................................................17
- Fuel Filter .......................................................... 17
- Spark Plug ......................................................... 18
- Cooling System ................................................. 1 8
- Exhaust System ................................................. 1 9
- Carburetor Adjustment ..................................... 20
- Drive Shaft Lubrication ..................................... 2 1
- Blade Replacement / Lubrication....................... 21
Troubleshooting ...................................................... 23
Storage..................................................................... 24
Specifications...........................................................25
Servicing Information...............................................28
- Parts/Serial Number ........................................... 28
- Service............................................................... 28
- ECHO Consumer Product Support .................... 28
- Warranty Card................................................... 2 8
- Additional or Replacement Manuals................. 28
Specifications, descriptions and illustrative material in this
literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories,
and may not include all standard equipment.
POWER EDGER
OPERATOR'S MANUAL
SAFETY
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to
3
DANGER
The safety alert symbol accompanied by the word
“DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or death
if not avoided.
W ARNING
The safety alert symbol accompanied by the word
“WARNING” calls attention to an act or condition
which CAN lead to serious personal injury or death
if not avoided.
CAUTION
The safety alert symbol accompanied by the word
“CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal injury
if not avoided.
INTERNA TIONAL SYMBOLS
Symbol form/
shape
Symbol
description/
application
Read and understand
Operator's Manual.
Symbol form/
shape
Symbol
description/
application
Fuel and oil mixture
CIRCLE AND SLASH SYMBOL
This symbol means the specific action
shown is prohibited. Ignoring these
prohibitions can result in serious or fatal
injury.
NOTE
This enclosed message provides tips for use, care
and maintenance of the unit.
IMPORTANT
The enclosed message provides information
necessary for the protection of the unit.
Symbol form/
shape
Symbol
description/
application
Keep feet away
from blade
Symbol form/
shape
Symbol
description/
application
Direction of
blade
Wear eyes, ears and
head protection
Hot
Surface
Safety/Alert
Avoid all power lines.
This unit is not
insulated against
electrical current.
Finger Severing
Wear hand
protection. Use
two handed.
DO NOT smoke
near fuel.
DO NOT allow
flames or sparks
near fuel.
Keep bystanders away
15 m (50 ft.)
Thrown
objects
Wear slip
resistant foot
wear.
Primer bulb
Carburetor
adjustment
- High speed
mixture
Choke Control
"Cold Start"
Position
(Choke Closed)
Emergency stop
Carburetor
adjustment
- Low speed
mixture
Ignition
ON/OFF
Carburetor
adjustment
- Idle speed
Choke Control
"Run"
Position
(Choke Open)
4
PERSONAL CONDITION AND SAFETY EQUIPMENT
W ARNING
Edger users risk injury to themselves and others if the edger is used improperly and or safety precautions are not
followed. Proper clothing and safety gear must be worn when operating an edger.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the edger.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your grip on the edger handles. Gloves also reduce the transmission of
machine vibration to your hands.
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY.
Wear sturdy work shoes with non-skid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy work for early
morning or late afternoon hours when temperatures are cooler.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning
sensations, followed by loss of color and numbness in the fingers. The following precautions are strongly recommended, because the minimum exposure which might trigger the ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands,
and wrists.
• Maintain good blood circulation by performing vigorous armexercises
during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the edger or other hand-held power equipment is not
required.
• If you experience discomfort, redness, and swelling of the fingers,
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
POWER EDGER
OPERATOR'S MANUAL
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position.
Instead, try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive movement.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness, or pain in the fingers, hands, wrists, or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
5
W ARNING
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual and
Safety Manual for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the unit
is in use.
Keep a Firm Grip
• Hold the front and rear handles with both hands, with thumbs and
fingers encircling the handles.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
Avoid Hot Surfaces
• Keep exhaust area clear of flammable debris. Avoid contact during
and immediately after operation.
6
EQUIPMENT
W ARNING
Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment
combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which
have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and
safety manual.
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
• Inspect fuel lines, tank, and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found.
• Inspect shield for damage, and that shield is securely in place. Replace if shield is damaged or missing.
• Check that the cutting attachment is firmly attached and in safe operating condition.
• Check that front handle is adjusted for safe, comfortable operation. See Assembly for proper adjustment.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.
EMISSION CONTROL
EPA Phase 2 / C.A.R.B. Tier III
The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank
the Control System is EVAP (Evaporative Emissions). Evaporative emission may be applicable to California models only.
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY: 7EHXS.0254KG DISPLACEMENT: 25.4 CC
EMISSION COMPLIANCE PERIOD : 300 HRS.
THIS ENGINE MEETS U.S. EPA PH2 EXH AND 2007 AND
LATER CALIFORNIA EXH AND EVAP EMISSION REGULATIONS FOR S.O.R.E.. REFER TO OWNER'S MANUAL FOR
MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by engine
FAMILY).
PRODUCT EMISSION DURABILITY
The 300 hour emission durability compliance period is the time span selected by the manufacturer certifying the
engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are
followed as listed in the Maintenance Section of this manual.
POWER EDGER
OPERATOR'S MANUAL
DESCRIPTION
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the
instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.
18
17
11
19
12
Hot Decal (near muffler)
13
14
P/N 89016006361
7
6
7
Shaft Decal
5
8
P/N 89016052631
16
15
4
3
2
1
9
10
P/N 89016025560
P/N X505001930
8
1. POWER HEAD - Factory assembled. Includes the engine, clutch, fuel system, ignition system and starter.
2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is
prevented unless throttle trigger lockout lever is engaged.
3. STOP SWITCH - "Slide Switch" mounted on top of the throttle Trigger Housing. Move switch FORWARD to
RUN, BACK to STOP.
4. FRONT HANDLE - The front handle can be repositioned for comfortable operation by loosening the screws and
moving the handle.
5. DEBRIS SHIELD/FLAP - Mounted over the cutting attachment. Helps protect operator by deflecting debris
produced during the edging operation.
6. BLADE - Rotates to provide cutting action.
7. WHEEL - Adjustable up/down, sets depth of blade.
8. DRIVE SHAFT ASSEMBLY - Contains a specially designed liner and the flexible drive shaft.
9. THROTTLE TRIGGER - Spring loaded to return to idle when released. When accelerating, press trigger gradually
for best operating technique.
10. GRIP - Rear (right hand) handle.
11. SPARK PLUG - Provides spark to ignite fuel mixture.
12. TOP GUARD - Protects arm from the hot engine.
13. RECOIL STARTER HANDLE - Pull recoil handle slowly until starter engages, then quickly and firmly. DO NOT let
handle snap back or damage to unit will occur.
14. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -The muffler or catalytic muffler controls exhaust noise
and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep
exhaust area clear of flammable debris.
15. FUEL TANK - Contains fuel and fuel filter.
16. FUEL TANK CAP - Cover and seals fuel tank.
17. CHOKE - The choke control is located on the air filter case. Move lever to "COLD START" ( ) to close choke for
cold starting. Move lever to "RUN" ( ) position to open choke.
18. AIR CLEANER ASSEMBLY - Contains replaceable felt element.
19. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the
carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb
an additional 4 or 5 times.
POWER EDGER
OPERATOR'S MANUAL
CONTENTS
The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions,
some assembly may be necessary.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
__ 1, Power Head
__ 1, Drive Shaft Assembly
__ 1, Plastic Bag (Co-Pack)
__ 1, Operator's Manual
__ 1, Safety Manual
__ 1 , Warranty Registration Card
__ 1 , ECHO Emissions and Warranty Statement
__ 1 , Echo Power Blend X
__ 1 , Front Handle
__ 1 , Lower Bracket, Front Handle
__ 4 , 5 x 35 mm screws
__ 4 , 5 mm nuts*
__ 1, T-Wrench
__ 2 , Split pin
__ 1 , 4 mm Hexagon Wrench
__ 1 , Locking Tool
__ 1 , 8 x 10 mm Spanner Wrench
__ 1, Safety Glasses
* 5mm nuts may not be needed.
TM
2-stroke oil sample
9
ASSEMBLY
Tools Required: 4 mm Hex Wrench, 8 x 10 mm Open-end Wrench
Parts Required: Power head, Drive Shaft Assembly
DRIVE SHAFT/POWER HEAD
1. Stand power head upright on a level surface.
2 . Loosen the two (2) drive shaft clamp bolts (B) at engine drive shaft
clamp, and remove center drive shaft location bolt (A).
3 . Remove dust cap and carefully fit drive shaft assembly to engine
making sure that inner drive shaft engages into clutch mount.
4 . Turn drive shaft housing until locating hole lines up with location
hole in clamp and install center drive shaft location bolt (A).
NOTE
Gear Housing must be aligned properly with engine. Aligning
center locating hole in driveshaft housing with center drive shaft
bolt (A) provides correct alignment.
B
A
B
10
5 . Tighten two (2) drive shaft clamp bolts (B) securely.
6. Route throttle linkage and ignition lead assembly along shaft and
clip as shown.
THROTTLE LINKAGE AND IGNITION LEADS
1 . Close choke and remove air filter cover.
2 . Place throttle linkage (C) through adjustment fixture (D) and install
wire end into large carburetor throttle swivel hole (E). Check throttle
for freedom of movement and that wide open throttle / low idle
extremes are adjusted properly. The throttle linkage must be
adjusted by moving the adjustment fixture (D). Consult with your
Echo Dealer for correct adjustment procedure.
3 . Connect 2 ignition stop leads (F, G) from throttle cable tubing to 2
ignition leads (F, G) on engine.
B
B
D
F
A
C
E
4 . Secure ignition leads against engine housing with clip (H).
5 . Install air filter and cover.
G
H
H
FRONT HANDLE
Tools Required: Cross-Head Screwdriver
Parts Required: Front Handle, Lower Bracket, 4 - 5 x 35 mm screws
NOTE
Label shows minimum spacing for front handle location.
1. Assemble front handle and bracket loosely to drive shaft.
POWER EDGER
OPERATOR'S MANUAL
11
2. Position front handle in comfortable operating position and tighten
screws.
MIN
SPACING
OPERATION
W ARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit.
NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor
performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage
section of this manual.
FUEL
W ARNING
Alternative fuels, such as E-20 (20% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are
NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to,
improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets,
carburetors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to
10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is
NOT approved.
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD Standards must be
used. Echo brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards. Engine problems due to
inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD certified oil, such as
Echo premium Power Blend X TM, will void the two-stroke engine warranty. (Emission related parts only are covered for
two years, regardless of two-stroke oil used, per the statement listed in the Emission Defect Warranty Explanation.)
12
IMPORTANT
Echo premium Power Blend X
sold in the past regardless of ratio specified in those manuals.
TM
Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo engines
Handling Fuel
W ARNING
Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.
• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
• DO NOT overfill fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.
Mixing Instructions
1 . Fill an approved fuel container with half of the required amount of
gasoline.
.S.UCIRTEM
oitaR1:05-xiMliOotleuF
2. Add the proper amount of 2-stroke oil to gasoline.
3 . Close container and shake to mix oil with gasoline.
4 . Add remaining gasoline, close fuel container, and remix.
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers to
reduce fuel spillage.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
Storage - Fuel storage laws vary by locality. Contact your local
government for the laws affecting your area. As a precaution, store fuel
in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames.
IMPORTANT
Stored fuel ages. Do not mix more fuel than you expect to use in
thirty (30) days, ninety (90) days when a fuel stabilizer is added.
SAGLIOSAGLIO
snollaG.zo.lFretiL.cc
1
2
5
6.2
2.5
31
4
8
02
08
061
004
IMPORTANT
Stored two-stroke fuel may separate. ALWAYS shake fuel
container thoroughly before each use.
STARTING COLD ENGINE
W ARNING
The attachment will operate immediately when the engine starts
and could result in loss of control and possible serious injury.
Keep movable parts of the attachment off the ground and away
from objects that could become entangled or thrown.
POWER EDGER
OPERATOR'S MANUAL
13
1. Stop Switch
Move stop switch (A) away from the STOP position.
2. Choke
Move choke (B) to “Cold Start” ( ) Position.
3. Purge Bulb
Pump purge bulb (C) until fuel will be visible and flows freely in
the clear fuel tank return line. Pump bulb an additional 4 or 5
times.
4. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts clear
of all obstacles. Firmly grasp right hand grip with left hand and fully
depress throttle trigger to wide open position. Rapidly pull recoil
starter handle/rope (D) until engine fires (or maximum five [5] pulls).
A
B
C
D
5. Choke
After engine fires or five (5) pulls, move choke lever back to “Run”
( ) position. Hold throttle trigger fully depressed and pull starter
handle/rope until engine starts and runs. Release throttle trigger
and allow unit to warm up at idle for several minutes.
NOTE
If engine does not start with choke in “Run” position after 5 pulls,
repeat instructions 2 - 5.
6 . After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.
D
14
STARTING WARM ENGINE
The starting procedure is the same as Cold Start except DO NOT close
the choke, and do not depress throttle trigger to wide open position.
W ARNING
The attachment should not move at idle, otherwise serious
personal injury may result.
NOTE
If attachment moves, readjust carburetor according to “Carburetor
Adjustment” instructions in this manual or see your ECHO Dealer.
1. Stop Switch
Move stop switch (A) away from the STOP position
A
2. Purge Bulb
Pump purge bulb (C) until fuel will be visible and flows freely in
the clear fuel tank return line. Pump bulb an additional 4 or 5
times.
3. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts clear
of all obstacles. Rapidly pull recoil starter handle/rope (D) until
engine fires.
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
STOPPING ENGINE
1. Throttle
Release throttle and allow engine to return to idle before shutting
off engine.
2. Stop Switch
Move stop switch (A) to STOP position.
C
D
D
A
W ARNING
If engine does not stop when stop switch is moved to STOP
position, close choke - COLD START position - to stall engine.
Have your ECHO dealer repair stop switch before using edger
again.
OPERATING TECHNIQUES
1. Before edging, water the area to soften the ground to make edging
easier.
2 Before edging, check the area and remove all obstacles and
objects that could be thrown.
3. Plan to edge regularly to make it easier to keep a neat edge and to
avoid having to make more than one pass.
NOTE
Blade depth may have to be adjusted due to differences in height
between the hard surface and the top of the grass.
W ARNING
Never adjust blade height with engine running, otherwise serious
personal injury may result.
POWER EDGER
OPERATOR'S MANUAL
15
4. Loosen adjustment knob and adjust the blade's depth of cut to
produce a fine cut between sidewalk and grass using a minimum blade depth, usually with about 13 mm (1/2 in.) of the
blade into the ground. Tighten adjustment knob.
5 . Before edging, plan your direction of travel so that the unit will
always be positioned on your right side and so that you walk on a
hard surface whenever possible.
6. Hold edger as shown.
W ARNING
Before edging, be sure to read and understand the entire
Operator's Manual to avoid the chance of serious injury.
7. When starting to edge, run the engine at full throttle, and lower the
blade gently into the ground, being careful not to hit the concrete
with the blade.
8 . Don't force the blade. Move as quickly as the blade will allow.
1/2 in.
WHEEL
ADJUSTMENT
KNOB
INCREASE
DEPTH
DECREASE
DEPTH
W ARNING
The complete unit, specifically the drive shaft assembly and
muffler exhaust area may become very hot during use. Avoid
contact during and immediately after operation, otherwise serious
personal injury may result.
16
MAINTENANCE
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.
Wear gloves to protect hands from sharp edges and hot surfaces.
Your ECHO edger is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
your edger achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your
unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the
ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for repairs.
SKILL LEVEL
Level 1 = Easy to do. Most required tools come with unit.
Level 2 = Moderate difficulty. Some specialized tools may be required.
Level 3 = Experience required. Specialized tools are required. ECHO recommends
that the unit be returned to your ECHO dealer for service.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.
MAINTENANCE INTERV ALS
/TNENOPMOC
METSYS
troPtsuahxErednilyCnobraceD/naelC/tcepsnI 3 C/I
retliFriAecalpeR/naelC/tcepsnI 1 C/I*R
ekohCnaelC/tcepsnI 2 C/I
retliFleuFecalpeR/tcepsnI 1 I*
skael,metsySleuFecalpeR/tcepsnI 1 )3(I*)3(R/I
metsySgnilooCnaelC/tcepsnI 2 C/I
rotserrAkrapSrelffuMecalpeR/tce
psnI 2 C/I*R/I
tfahSevirDesaerG 2 )1(I
gnisuoHraeGesaerG 2 )2(I
epoRretratSlioceRnaelC/tcepsnI 1 *C/I*R/I
gulPkrapSnael
C/tcepsnI 2 C/I*R
ECNANETNIAM
ERUDECORP
D'QER
LLIKS
LEVEL
etniaMflesruoY-tI-oD
ROYLIAD
EROFEB
ESU
YREVE
LEUFER
serudecorPecnan
3
SHTNOM
09RO
SRUOH
serudecorPecnanetniaMrelaeDohcEdednemmoceR
6
SHTNOM
072RO
SRUOH
YLRAEY
006
SRUOH
R
)1( OHCEylppA
)2( OHCEylppA
)3( .ytirgetninoissimeniatniamotecnanetniamralugereriuqerTONODsknatleufevitaropav
* ..noitcepsnignirudraewroegamadfognidnifehtnodesaberaecalperotsnoitadnemmocerllA
tnemecalpeRedalBecalpeR/tcepsnI 1 II *R/I
stloB/stuN/swercSecalpeR/nethgiT/tcepsnI 1 *R/I
-ETONTNATROPMI deriuqerfoycneuqerfehtenimretedlliwecneirepxeruoydnaesulaut
.ecnanetniam
MT
EBUL
®
MT
EBUL
ewoL
®
SEDOCRETTELERUDECORPECNANETNIAM NAELC=C,ECALPER=R,TCEPSNI=I:
:SETONERUDECORPECNANETNIAM
.esufosruoh52yreve
cA.mumixameranwohsslavretniemiT
.esufosruoh52-51yreve
AIR FILTER
Level 1.
Tools required: 25 or 50 mm (1 or 2 in.) Cleaning brush
Parts required: Air Filter
1 . Close choke (Cold Start Position [ ]). This prevents dirt from
entering the carburetor throat when the air filter is removed. Brush
accumulated dirt from air cleaner area.
2 . Remove air filter cover. Brush dirt from inside cover.
3 . Remove air filter and lightly brush debris from filter. Replace filter if
it is damaged, fuel soaked, very dirty, or the rubber sealing edges
are deformed.
POWER EDGER
OPERATOR'S MANUAL
17
4 . If filter can be reused, be certain it:
• Fits tightly in the air filter cavity.
• Is installed with the original side out.
5 . Install air filter cover.
FUEL FILTER
Level 1.
Tools required: 200-250 mm (8-10 in.) length of wire with one end bent
into a hook, clean rag, funnel, and an approved fuel
container.
Parts required: Fuel Filter
W ARNING
Fuel is VERY flammable. Use extreme care when mixing, storing or
handling.
1 . Use a clean rag to remove loose dirt from around fuel cap and
empty fuel tank.
2 . Use the “fuel line hook” to pull the fuel line and filter from the
tank.
3 . Remove the filter from the line and install the new filter.
18
SPARK PLUG
Level 2.
Tools Required: T-Wrench, feeler gauge, soft metal brush
Parts Required: Spark Plug NGK BPM-8Y
IMPORTANT
Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) otherwise
severe engine damage may occur.
1 . Remove spark plug and check for fouling, worn and rounded
center electrode.
2 . Clean the plug or replace with a new one. DO NOT sand blast to
clean. Remaining sand will damage engine.
3. Adjust spark plug gap by bending outer electrode.
4 . Tighten spark plug to 150-170 kg/cm (130-150 in. lb.).
COOLING SYSTEM
Level 2.
Tools required: Cross Head Screwdriver, 3 & 4 mm Hex Wrench,
Cleaning Brush, 25 - 50 mm (1 - 2 in.)
Parts Required: None if you are careful.
IMPORTANT
To maintain proper engine operating temperatures, cooling air
must pass freely through the cylinder fin area. This flow of air
carries combustion heat away from the engine.
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching the
cylinder.
• Dust and grass build up on the outside of the cylinder. This build up
insulates the engine and prevents the heat from leaving.
0.65 mm
(0.026 in.)
Removal of cooling passage blockages or cleaning of cooling fins is
considered “Normal Maintenance.” Any failure attributed to lack of
maintenance is not warranted.
1 . Remove spark plug lead.
2 . Remove air cleaner cover.
3 . Remove muffler cover screw and muffler cover (A).
4 . Remove 2 engine cover screws and engine cover (B).
A
B
IMPORTANT
DO NOT use a metal scraper to remove dirt from the cylinder fins.
5 . Use brush to remove dirt from the cylinder fins.
6 . Remove grass and leaves from the grid between the recoil starter
and fuel tank.
7. Assemble components in reverse order.
EXHAUST SYSTEM
Spark Arrestor Screen
Level 2.
Tools Required: Cross Head Screwdriver, 4mm Hex Wrench, Soft
Metal Brush
POWER EDGER
OPERATOR'S MANUAL
19
Parts Required: Spark Arrestor Screen, Gasket
1 . Remove two (2) muffler cover screws and muffler cover (A).
2 . Place piston at Top Dead Center (TDC) to prevent carbon/dirt from
entering cylinder.
3 . Remove spark arrestor screen (B), gasket (C) and exhaust guide (D)
from muffler body.
4 . Clean carbon deposits from muffler components.
NOTE
When cleaning carbon deposit, be careful not to damage the
catalytic element inside muffler.
5 . Replace screen if it is cracked, plugged or has holes burned
through.
6. Assemble components in reverse order.
Cylinder Exhaust Port
Level 3.
A
C
D
B
IMPORTANT
The cylinder exhaust port must be inspected and cleaned of excess
carbon every 3 months or 90 hours of operation in order to maintain
this engine within the emissions durability period. ECHO strongly
recommends that you return your unit to your ECHO dealer for this
important maintenance service.
20
CARBURETOR ADJUSTMENT
Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel
break-in before carburetor adjustments can be made. During the break-in
period your engine performance will increase and exhaust emissions will
stabilize. Idle speed can be adjusted as required.
High Altitude Operation
This engine has been factory adjusted to maintain satisfactory starting,
emission, and durability performance up to 1,000 feet above mean sea
level (MSL). To maintain proper engine operation above 1,000 feet MSL
the carburetor must be adjusted by an authorized ECHO service dealer.
IMPORTANT
If the engine is adjusted for operation above 1,000 feet MSL, the
carburetor must be re-adjusted when operating the engine below
1,000 feet MSL, otherwise severe engine damage can result.
Level 2.
Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017)
Parts required: None
NOTE
Every unit is run at the factory and the carburetor is set in compliance with emission regulations. This carburetor does not have
acceleration and high speed adjustment needles.
1 . Check idle speed and reset if necessary. If a tachometer is avail-
able, idle speed screw (A) should be set to the specifications found
on page 25 "Specifications" of this manual. Turn idle screw (A)
clockwise to increase idle speed; counter clockwise to decrease idle
speed.
W ARNING
When carburetor adjustment is completed, the cutting attachment should not turn at idle, otherwise serious personal injury
may result.
A
DRIVE SHAFT LUBRICATION
Level 1.
Tools required: 8 mm Open End Wrench, 4 mm Hex Wrench,
Clean rag
Parts Required: ECHO® LUBETM 8 oz. (P/N 91014) or Lithium Base
Grease.
1 . Loosen two (2) screws (A) and remove center locating screw (B).
Pull gear box and shield from drive shaft housing.
2 . Pull flexible cable from the drive shaft housing, wipe clean and
recoat with a thin coating [15 ml (1/2 oz.)] of grease.
POWER EDGER
OPERATOR'S MANUAL
A
21
3 . Slide the flexible cable back in the drive housing. DO NOT get
dirt on the flex cable.
4. Install the gear housing and shield assembly.
BLADE REPLACEMENT/LUBRICATION
Level 1.
Tools Required: T-wrench, Locking Tool, Needle Nose Pliers,
13 mm Open End Wrench
Parts Required: ECHO® LUBETM 8 oz. (P/N 91014) or Lithium Base
Grease, Blade P/N 69601552632, split pin P/N
90030020022
NOTE
Grease gear case every 15 - 25 hours of use. Replace blade when it
is worn shorter than 6 inches. Remove blade and adapters before
greasing to prevent damage to gear and bearings.
B
1 . Shut engine off. Disconnect spark plug lead from spark plug.
22
2 . Remove split pin (A).
3 . Rotate blade until holes in inner blade adapter (B) and gear box
align. Insert locking tool to lock PTO shaft (C).
NOTE
Blade nut (D) is left hand thread.
B
C
4 . Remove blade nut (D) in a clockwise direction using T-wrench.
Remove outer blade adapter (E), blade (F) and inner blade adapter
(B).
5 . Clean all loose debris from gear box.
6 . Remove plug (G) and check level of grease. Grease should fill gear
case to bottom of grease plug hole.
7. Add grease if necessary using manual grease gun or squeeze-type
tube. Do not use high pressure grease gun. DO NOT over-fill.
8 . Install inner blade adapter (B) onto PTO shaft (C).
9 . Install and center new blade (F) onto inner adapter (B).
10 . Install outer adapter (E) and nut (D). Tighten nut (D) firmly,
counterclockwise (CCW).
IMPORTANT
Never reuse old split pin.
F
E
D
A
11. Install new split pin (A) to secure nut.
TROUBLESHOOTING
melborPkcehCsutatSesuaCydemeR
POWER EDGER
OPERATOR'S MANUAL
TRAHCGNITOOHSELBUORTMELBORPENIGNE
23
roterubractaleuF
enignE
-sknarc
/drahstrats
t'nseod
trats
enignE
,snur
roseidtub
tonseod
ecca
etarel
ylreporp
rednilyctaleuF
dnetakrapS
eriwgulpfo
gulptakrapSkrapsoN
retlifriAytridretlifriAraewlamroNecalperronaelC
retlifleuFytridretlifleuF
tnevleuFdeggulptnevleuF
gulPkrapSnrow/ytridgulPraew
roterubraC
taleufoN
roterubrac
krapsoN
reporpmI
tnemtsujda
euF
roterubraC
rednilyctaleufoNroterubraCrelae
leufhtiwtewrelffuMhcirooterutxiMleuF
edgulP
evitcef
leufni
leufni
lamroNecalperrotsujdadnanaelC
noitarbiVtsujdA
deggolcreniartsleuF
deggolcenill
ffohctiwspotS
melborplacirtcelE
hctiwskcolretnI
tcerrocnipagkrapS
nobrachtiwderevoC
leufhtiwdeluoF
seudiser/stnanimatnoC
seudiser/stnanimatnoC
ecalpeR
ecalperronaelC
ecalperronaelC
relaedohcEruoyeeS
dohcEruoyeeS
ekohcnepO
retlifriaecalper/naelC
roterubractsujdA
hcEruoyeeS
gulpecalpeR
relaedo
NOothctiwsnruT
dohcEruoyeeS
relae
relaedohcEruoyeeS
).ni620.0(mm56.ottsujdA
ecalperronaelC
ecalperronaelC
ecalperronaelC
metsySgnilooC
rotserrAkrapS
neercS
enignE
d
seo
n
to
c
knar
A/NA/NmelborpenignelanretnIrelaedohcEruoyeeS
id
evissecxE
sirbed/tr
,dekcarcneercS
ro,deggulp
detarofrep
ra
ewlamroNecalpeR
ninoitarepodednetxE
snoitacolytsud/ytrid
naelC
DANGER
Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result.
24
STORAGE
W ARNING
During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear
of flammable debris during transportation or when storing, otherwise serious property damage or personal injury
may result.
Long Term Storage (over 30 days)
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following:
1 . Store unit in a dry, dust free place, out of the reach of children.
DANGER
Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.
2. Place the stop switch in the "STOP" position.
3 . Remove accumulation of grease, oil, dirt and debris
from exterior of unit.
4 . Perform all periodic lubrication and services that are
required.
5. Tighten all the screws and nuts.
6. Drain the fuel tank completely and pull the recoil
starter handle several times to remove fuel from the
carburetor.
7 . Remove the spark plug and pour 7 cc (1/4 oz.) of
fresh, clean, two-stroke engine oil into the cylinder
through the spark plug hole.
A. Place a clean cloth over the spark plug hole.
B . Pull the recoil starter handle 2-3 times to distribute
the oil inside the engine.
C. Observe the piston location through the spark plug
hole. Pull the recoil handle slowly until the piston
reaches the top of its travel and leave it there.
8. Install the spark plug (do not connect ignition cable).
POWER EDGER
OPERATOR'S MANUAL
SPECIFICATIONS
MODEL -----------------------------------------------------PE-265
Length-------------------------------------------------------1760 mm (69.3 in.)
Width-------------------------------------------------------- 245 mm (9.65 in.)
Height -------------------------------------------------------315 mm (12.4 in.)
Weight (dry w/cutter head)------------------------------- 6.2 kg (13.7 lb.)
Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine
Bore----------------------------------------------------------34.0 mm (1.34 in.)
Stroke--------------------------------------------------------28.0 mm (1.10 in.)
Displacement -----------------------------------------------25.4 cc (1.55 cu. in.)
Exhaust ------------------------------------------------------ Spark Arrestor Muffler / with catalyst
Carburetor --------------------------------------------------Zama w/purge bulb
Ignition System -------------------------------------------- CDI (capacitor discharge ignition)
Spark Plug --------------------------------------------------NGK BPM-8Y 0.65mm (0.026 in.)
Fuel ----------------------------------------------------------Mixed (Gasoline and Two-stroke Oil)
Fuel/Oil Ratio -----------------------------------------------50 : 1 Power Blend X™ ISO-L-EGD (ISO/CD 13738) and J.A.S.O.
M345- FC/FD, two-stroke, air-cooled engine oil.
Gasoline -----------------------------------------------------Use 89 Octane unleaded. Do not use fuel containing methyl
alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use
alternative fuels such as E-20 or E-85.
Oil ------------------------------------------------------------ Power Blend X TM Premium Universal 2-Stroke Oil
Fuel Tank Capacity ----------------------------------------0.5 lit. (16.9 US fl. oz.)
Recoil Starter System --------------------------------------Automatic Recoil Starter
Clutch ------------------------------------------------------- Centrifugal Type
Drive Shaft -------------------------------------------------- 6.35 mm (1/4 in.) flexible shaft
Gear Ratio ---------------------------------------------------2.07:1
Rotation Direction ----------------------------------------- Clockwise viewed from right side
Shield -------------------------------------------------------- Open anti-clog
Standard Cutter Head ------------------------------------- Metal blade
Blade Length ----------------------------------------------- 203.2 mm (8.0 in.)
Blade Width ------------------------------------------------50.8 mm (2 in.)
Blade Thickness ------------------------------------------- Standard 2.3 mm (0.090 in.), Premium 4.6 mm (0.181 in.)
Handle------------------------------------------------------- Front Cushioned D-loop, Rear - Grip
Vibration Reduction ---------------------------------------Rubber Cushion
Idle Speed (RPM) ------------------------------------------2,600 - 3,200
Clutch Engagement Speed (RPM) ----------------------- 3,600 - 4,200
Wide Open Throttle Speed (RPM) ---------------------- 10,400 - 11,400
25
26
NOTES
NOTES
POWER EDGER
OPERATOR'S MANUAL
27
SERVICING INFORMATION
PARTS
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for
your ECHO products are available only from an Authorized ECHO
Dealer. When you do need to buy parts always have the Model
Number, Type and Serial Number of the unit with you. You can find
these numbers on the engine housing. For future reference, write them
in the space provided below.
Model No. _____________ Type _________SN. ______________
/SERIAL NUMBER
SERVICE
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on our
Web Site. When presenting your unit for Warranty service/repairs,
proof of purchase is required.
ECHO CONSUMER PRODUCT SUPPORT
If you require assistance or have questions concerning the application,
operation or maintenance of this product you may call the ECHO
Consumer Product Support Department at 1-800-673-1558 from 8:30 am
to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.
WARRANTY REGISTRATION
To ensure trouble free warranty coverage it is important that you
register your ECHO equipment on-line at www.echo-usa.com. Other
registration options are by automated phone at 1-800-432-3246 or by
filling out the warranty registration card supplied with your unit.
Registering your product confirms your warranty coverage and
provides a direct link between you and ECHO if we find it necessary to
contact you.
DEALER?
Call
1-800-432-ECHO
1-800-432-3246
or
www.echo-usa.com
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
ADDITIONAL OR REPLACEMENT MANUALS
Safety Manuals in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at
www.echo-usa.com.
Operator's and Parts Manuals are available by:
• Downloading free from www.echo-usa.com
• Purchasing from your Echo Dealer.
• Manuals are available by sending a written request stating the model number and serial number of your Echo unit, part
number of the manual, your name and address, and mail to the address below.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
ECHO, INCORPORATED
400 OAKWOOD ROAD
LAKE ZURICH, IL 60047
www.echo-usa.com
S75811001001/S75811999999
Loading...