Echo PB-755S T, PB-755S H User Manual

Page 1
Power Blower
Operator's Manual
MODEL: PB-755S H
PB-755S T
WARNING
X7531122803
Read rules for safe operation and all instructions carefully. ECHO provides this Operator's Manual which must be read and understood for proper and safe operation.
Page 2
2

INTRODUCTION

Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job­dependability. Read and understand this manual. You will find it easy to use and full of helpful operating tips and SAFETY messages.
THE OPERATOR'S MANUAL
Read and understand this manual before operation. Keep it in a safe place for future reference. It contains specifications and information for operation, starting, stopping, maintenance, storage and assembly specific to this product.

TABLE OF CONTENTS

Introduction ...............................................................2
- The Operator's Manual ....................................... 2
Safety .........................................................................3
Manual Safety Symbols and Important Information .. 3
- International Symbols ......................................... 3
- Personal Condition and Safety Equipment ......... 3
- Equipment ........................................................... 6
Emission Control ........................................................ 6
Description ................................................................ 7
Contents .................................................................. 11
Assembly ................................................................. 12
- Install Blower Pipes PB-755SH .......................... 12
- Install Blower Pipes PB-755ST .......................... 13
Operation ................................................................. 14
- Fuel ................................................................... 14
- Starting Cold Engine ......................................... 16
- Starting Warm Engine ....................................... 17
- Stopping Engine ............................................... 17
- Operating Blower .............................................. 18
Maintenance ............................................................ 19
- Skill Levels ........................................................ 19
- Maintenance Intervals ...................................... 19
- Air Filter ............................................................ 20
- Fuel Filter .......................................................... 20
- Spark Plug ......................................................... 21
- Cooling System ................................................. 21
- Exhaust System ................................................. 22
- Carburetor Adjustment ................................... 2 3
Troubleshooting ..................................................... 25
Storage .................................................................... 26
Specifications......................................................... 27
Servicing Information ............................................ 28
- Parts/Serial Number ................................................ 28
- Service ............................................................. 28
- ECHO Consumer Product Support ................. 28
- Warranty Card ................................................. 28
- Additional or Replacement Manuals .............. 28
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publica­tion, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment.
CopyRight© 2009 By Echo, Incorporated All Rights Reserved.
Page 3

SAFETY

POWER BLOWER
OPERATOR'S MANUAL
3
MANUAL
SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.
The safety alert symbol accompanied by the word
DANGER
“DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided.
WARNING
The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided.
CAUTION
The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition
NOTE
This enclosed message provides tips for use, care and maintenance of the unit.
IMPORTANT
The enclosed message provides information necessary for the protection of the unit.
CIRCLE AND SLASH SYMBOL
This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result in serious or fatal injury.
which may lead to minor or moderate personal injury if not avoided.
INTERNATIONAL SYMBOLS
Symbol form/shape
Symbol
description/application
Read and understand
Operator's Manual.
Wear eyes, ears and
head protection
Hot
Surface
Safety/Alert
DO NOT allow
flames or sparks
near fuel.
Symbol form/shape
Symbol
description/application
Fuel and oil mixture
Finger Severing
Wear hand
protection. Use
two handed.
Wear slip
resistant foot
wear.
DO NOT smoke
near fuel.
Symbol form/shape
Symbol
description/application
Emergency stop
Carburetor adjustment
- Low speed mixture
Carburetor adjustment
- Idle speed
Choke Control
"Cold Start"
Position
(Choke Closed)
Symbol form/shape
description/application
Primer bulb
Carburetor adjustment
- High speed mixture
Choke Control
(Choke Open)
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING
Power Blower users risk injury to themselves and others if the power blower is used improperly or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a blower.
Symbol
Ignition
ON/OFF
"Run"
Position
Page 4
4
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the unit.
Hand Protection
Wear no-slip, heavy-duty work gloves to improve your grip on the blower handle. Gloves also reduce the transmission of machine vibration to your hands.
Breathing Protection
Wear a facemask to protect against dust.
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, and JEWELRY.
Wear sturdy work shoes with nonskid soles:
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Keep long hair away from engine and blower intake. Retain hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations, followed by loss of color and numbness in the fingers. The following precautions are strongly recom­mended, because the minimum exposure, which might trigger the ailment, is unknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands, and wrists.
• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held power equipment is not required.
• If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling, consult your physi­cian before further exposing yourself to cold and vibration.
Page 5
POWER BLOWER
OPERATOR'S MANUAL
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive movement.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage can be pre­vented.
5
DANGER
Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual and Safety Manual for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15 m (50 ft.) while the unit is in use.
• Take wind conditions into account: avoid open doors and windows.
• Do not point blower at people or animals.
Keep a Firm Grip
• Hold the front and rear handles with both hands, with thumbs and fingers encircling the handles.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach.
Avoid Hot Surfaces
• Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation.
Page 6
6
EQUIPMENT CHECK
WARNING
Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety manual.
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
• Do not use blower if any part is missing or damaged.
• Have repairs done only by an authorized ECHO Service dealer.
• Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.
ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.
WARNING
Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found, do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an authorized servicing dealer before using.

EMISSION CONTROL (EXHAUST & EVAPORATIVE)

EPA Phase 2 / C.A.R.B. TIER III
The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be appli­cable to California models only.
An Emission Control Label is located on the unit. (This is an EXAMPLE ONLY, information on label varies by engine FAMILY).
PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)
The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual.
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY: 9EHXS.0635KB DISPLACEMENT: 63.3 CC
EMISSION COMPLIANCE PERIOD : 300 HRS.
THIS ENGINE MEETS U.S. EPA PH2 EXH AND 2007 AND
LATER CALIFORNIA EXH AND EVAP EMISSION REGULA-
TIONS FOR S.O.R.E. REFER TO OWNER'S MANUAL FOR
MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
Page 7
POWER BLOWER
OPERATOR'S MANUAL

DESCRIPTION

PB-755SH
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDER­ING instructions for specific information.
1
2
11
10
Hot Decal (near muffler)
P/N X505002310
7
9
12
13
8
7
General Warning Decal (located on blower housing)
3
6
4
5
P/N 89016009461
Sound Label (located on blower housing)
74 Category III
Measured at 50 ft. (15m) per ANSI B175.2
dB(A)
P/N X508000180
Page 8
8
1. SPARK PLUG - Provides spark to ignite fuel mixture.
2. SAFETY DECAL - Lists important safety precautions.
3. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER - The muffler or catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris.
4. CHOKE - Move lever up to "Cold Start" (
Run position ( ).
5. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb an additional 4 or 5 times.
6. RECOIL STARTER HANDLE - Pull recoil handle slowly until starter engages, then quickly and firmly. When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.
7. FUEL TANK - Contains fuel and fuel filter.
8. FUEL TANK CAP - Covers and seals fuel tank.
9. AIR CLEANER - Contains replaceable air filter element.
10. HANDLE - Rotates downward for throttle control access. Spring loaded for flexible operation.
11. BLOWER PIPES - Exclusive positive locking system.
12. SHOULDER HARNESS - Used to support unit on operator's back. The straps are adjustable.
13. THROTTLE POSITION LEVER/STOP SWITCH - Combination stop switch and variable speed throttle lever. When the lever is moved all the way forward the blower is at Wide Open Throttle (W.O.T.). When the lever is moved rearward to detent, the blower is at idle. When the lever is moved rearward past the idle detent the blower will stop.
) starting position and for emergency stopping. Move lever down to
Page 9
POWER BLOWER
OPERATOR'S MANUAL
PB-755ST
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDER­ING instructions for specific information.
11
12
10
Hot Decal (near muffler)
1
P/N X505002310
9
13
14
15
2
9
3
6
8
7
4
5
17
16
General Warning Decal (located on blower housing)
P/N 89016009461
Sound Label (located on blower housing)
74 Category III
Measured at 50 ft. (15m) per ANSI B175.2
dB(A)
P/N X508000180
Page 10
10
1. SPARK PLUG - Provides spark to ignite fuel mixture.
2. SAFETY DECAL - Lists important safety precautions.
3. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER - The muffler or catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris.
4. CHOKE - Move lever up to "Cold Start" (
Run position ( ).
5. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb an additional 4 or 5 times.
6. RECOIL STARTER HANDLE - Pull recoil handle slowly until starter engages, then quickly and firmly. When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.
7. FUEL TANK - Contains fuel and fuel filter.
8. FUEL TANK CAP - Covers and seals fuel tank.
9. AIR CLEANER - Contains replaceable air filter element.
10. THROTTLE POSITION LEVER - Pull back to increase engine speed. Friction washers maintain throttle lever
setting.
11. STOP SWITCH - Slide switch mounted on top of handle. Move forward to run, back to stop.
12. HANDLE - Used by operator to direct and control air flow.
) starting position and for emergency stopping. Move lever down to
13. SHOULDER HARNESS - Used to support unit on operator's back. The straps are adjustable.
14. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradually for best operating technique.
15. LOCKING KNOB - Allows operator to adjust handle position for optimum comfort and control.
16. BLOWER PIPES - Exclusive positive locking system.
17. FLEXIBLE PIPE - Allows for full range of movement.
Page 11

CONTENTS

PB-755S H
__ 1 - Power Head __ 1 - Flex Pipe __ 1 - Pipe w/swivel __ 1 - Straight Pipe __ 1 - Straight Pipe __ 1 - Operator's Manual __ 1 - Warranty Registration Card __ 1 - ECHO Emissions and Warranty Statement __ 1 - Plastic Bag __ 2 - Clamps w/screws __ 1 - Stick Handle __ 1 - Bolt 6x45 __ 1 - Washer 6 __ 1 - Wing Nut __ 1 - Echo Power Blend X TM 2-stroke oil sample
POWER BLOWER
OPERATOR'S MANUAL
11
PB-755S T
__ 1 - Power Head __ 1 - Flex Pipe __ 1 - Pipe w/swivel __ 1 - Straight Pipe __ 1 - Straight Pipe __ 1 - Operator's Manual __ 1 - Warranty Registration Card __ 1 - ECHO Emissions and Warranty Statement __ 1 - Plastic Bag __ 2 - Clamps w/screws __ 1 - Guide Loop __ 1 - Echo Power Blend X TM 2-stroke oil sample
Page 12
12

ASSEMBLY

PB-755SH
WARNING
Never perform maintenance or assembly procedures with engine running or serious personal injury may result.

INSTALL BLOWER PIPES / STICK HANDLE (H)

1. Assemble clamps (A) onto both ends of flexible pipe (B).
2. Assemble swivel pipe (C) into flexible pipe (B) and tighten clamp (A).
3. Assemble flexible pipe (B) to elbow (D) on blower and tighten clamp (A).
NOTE
A light lubricant may be used to ease assembly of flexible pipe to blower elbow.
4. Loosen wing nut (E) completely and open stick handle clamp.
5. Align notches (F) in handle clamp with tabs (G).
6. Slide stick handle onto swivel pipe (C). Stick handle should be angled away from operator.
7. Position stick handle (H) for comfortable operation, and tighten wing nut (E).
8. Assemble straight pipe (I) onto swivel pipe (C), until you feel light resistance. Do not force connection. Hold swivel pipe and turn straight pipe clockwise, engaging positive locking channels, until connection is firm. Do not force connection.
A
D
B
B
G
G
A
C
H
F
E
9. Assemble straight pipe with decal (J) to straight pipe (I) as in step 8.
NOTE
Blower use will eventually loosen pipe connections. Exclusive positive locking system allows pipes to be tightened. If loosening occurs, remove two straight pipes and install according to instructions 8 & 9.
C
I
J
Page 13
PB-755ST
POWER BLOWER
OPERATOR'S MANUAL
13
WARNING
Never perform maintenance or assembly procedures with engine running or serious personal injury may result.

INSTALL BLOWER PIPES (T)

1. Place guide loop (G) across large clamp, and turn until clip fully engages clamp band.
NOTE
Clamp with cable guide loop (G) fits large end of flexible pipe (B).
2. Assemble clamps (A) onto both ends of flexible pipe (B).
3. Assemble flexible pipe (B) to elbow (D) on blower. Position guide loop (G) on inside (blower side) of flexible tube and tighten clamp (A).
NOTE
A light lubricant may be used to ease assembly of flexible pipe to blower elbow.
NOTE
Hang handle freely from blower to assure throttle cable is not twisted before installing handle (E).
4. Position cable between the elbow (D) and frame and along the top of the flexible pipe. Loosen knob (H) on handle (E). Align notch in handle with tabs (F). Install onto swivel pipe (C) past long ridges in pipe.
5. Assemble swivel pipe (C) into flexible pipe (B) and tighten clamp (A).
6. Clip throttle cable into throttle cable guide loop (G).
G
A
D
G
B
E
B
C
G
G
A
F
H
E
H
7. Move handle (E) to desired position. Tighten knob (H) hand tight.
8. Assemble straight pipe (I) onto swivel pipe (C), until you feel light resistance. Do not force connection. Hold swivel pipe and turn straight pipe clockwise, engaging positive locking channels, until connection is firm. Do not force connection.
9. Assemble straight pipe with decal (J) to straight pipe (I) as in step
8.
NOTE
Blower use will eventually loosen pipe connections. Exclusive positive locking system allows pipes to be tightened. If loosening occurs, remove two straight pipes and install according to instruc­tions 8 & 9.
J
E
I
C
Page 14
14

OPERATION

WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Blower housing may contain shredder blades and other sharp edges that can cause serious injuries if touched, even if engine is off and blades are not moving. Wear gloves to protect hands from sharp edges and hot surfaces.
WARNING
Operation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped with a spark arrestor and a spark arrestor may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.
NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual.

FUEL

WARNING
Alternative fuels, such as E-20 (20% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is
NOT approved.
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and JASO M345/FC/FD Standards
must be used. ECHO brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards. Engine prob­lems due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and JASO M345/FC/FD certified oil, such as ECHO premium Power Blend X TM, will void the two-stroke engine warranty.
IMPORTANT
Echo premium Power Blend X TM Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo engines sold in the past regardless of ratio specified in those manuals.
Page 15
POWER BLOWER
OPERATOR'S MANUAL
Handling Fuel
DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.
• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
• DO NOT overfill fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.
15
Mixing Instructions
1. Fill an approved fuel container with half of the required amount of
gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and remix.
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container.
Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccu­pied building, away from sparks and flames.
IMPORTANT
Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added.
.S.UCIRTEM
SAGLIOSAGLIO
snollaG.zo.lFretiL.cc
1 2 5
Shoulder
level
6.2
2.5
31
4 8
02
Fuel tank
oitaR1:05-xiMliOotleuF
08
061
004
IMPORTANT
Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use.
Page 16
16

STARTING COLD ENGINE

• Recoil starter: Use short pulls - only 1/2-2/3 of rope length for starting. Do not allow the rope to snap back in. Always hold the unit firmly.
PB-755SH
1. Throttle Lever Move throttle lever (A) to IDLE DETENT position.
PB-755ST
1. Throttle Lever/Stop Switch Move throttle lever (A) forward to idle position. Slide stop switch (B) forward to run position.
PB-755SH, PB-755ST
2. Choke
Move choke (C) up to "Cold Start" position ( ).
3. Purge Bulb Pump purge bulb (D) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times.
PB-755SH
PB-755ST
C
A
B
A
4. Recoil Starter Pull recoil starter handle (E) until engine fires (5 or 6 pulls maxi­mum).
5. Choke
Move choke (C) down to run position ( ), and if necessary,
restart engine.
NOTE
If engine does not start after 5 pulls, move choke to "Cold Start" position, and repeat steps 4 & 5.
NOTE
Allow engine to warm up before use.
D
C
E
Page 17

STARTING WARM ENGINE

PB-755SH
1. Throttle Lever Move throttle lever (A) to IDLE DETENT position.
PB-755ST
1. Throttle Lever/Stop Switch Move throttle lever (A) forward to idle position. Slide stop switch (B) forward to run position.
PB-755SH, PB-755ST
2. Recoil Starter Pull recoil starter handle (E) and engine should start. Do not use choke (C).
POWER BLOWER
OPERATOR'S MANUAL
PB-755SH
PB-755ST
A
A
B
17
NOTE
If engine does not start after 5 pulls, use cold start procedures.

STOPPING ENGINE

PB-755SH
1. Throttle Lever Move throttle lever (A) to idle detent position and allow engine to return to idle before shutting off engine.
2. Move throttle lever (A) to "O" (Stop) position.
PB-755ST
1. Throttle Trigger/Throttle Position Lever Release throttle trigger (C). Move throttle position lever (A) forward to idle position and allow engine to return to idle before shutting engine off.
2. Stop Switch Slide stop switch (B) to Stop position.
PB-755SH
PB-755ST
C
E
A
B
WARNING
If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using blower again.
A
C
Page 18
18

OPERATING BLOWER

WARNING
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body.
WARNING
Always wear safety glasses, hearing protection, a face filter mask and take all safety precautions or serious personal injury may result. Do not point the blower pipe in the direction of people or pets.
Read the Safety Section on pages 4 - 6 carefully.
IMPORTANT
To avoid engine damage due to over-revving, do not block blower pipe opening.
1. Use only during appropriate hours.
2. Allow the engine to warm up at a fast idle for a few minutes.
3. PB-755SH Set engine speed with throttle lever (A).
PB-755ST
Control engine speed with throttle trigger (C), or throttle position lever (A). Rotate throttle position lever forward for lower speed, back for higher speed.
4. Use lower speed to blow dry leaves from walks, patios and drives.
5. Additional speed may be necessary to clean grass and leaves from a lawn or flower bed.
6. Higher speed may be necessary to move gravel, dirt, snow, bottles or cans from a driveway, street, parking lot or stadium.
PB-755SH
PB-755ST
A
C
A
NOTE
Never use a higher speed setting than necessary to perform a task. Remember, the higher the engine speed, the louder the blower noise. Minimize dust by using blower at lower speeds and by dampening material with water/mist when necessary. Keep debris on your property. Be Smart - be a good neighbor.
Page 19
POWER BLOWER
OPERATOR'S MANUAL
19
MAINTENANCE
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Wear gloves to protect hands from sharp edges and hot surfaces.
Your ECHO blower is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your blower achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If task is not listed, see your ECHO Dealer for repairs.
SKILL LEVELS
Level 1 = Easy to do. Common tools may be required. Level 2 = Moderate difficulty. Some specialized tools may be required.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.
MAINTENANCE INTERVALS
COMPONENT / SYSTEM
Air Filter Inspect/Clean
Choke Shutter Inspect/Clean
Fuel Filter Inspect/Replace
Fuel Cap Gasket Inspect/Replace
Fuel System Inspect/Replace
Spark Plug Inspect/Clean/Replace
Cooling System Inspect/Clean
Muffler Spark Arrestor Inspect/Clean/Replace
Cylinder Exhaust Port Inspect/Clean/Decarbon
Recoil Starter Rope Inspect/Clean
Screws/Nuts/Bolts Inspect/Tighten/Replace
MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN
IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the
frequency of required maintenance.
MAINTENANCE PROCEDURE NOTES:
(1) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.
* All recommendations to replace are based on the finding of damage or wear during inspection.

MAINTENANCE

PROCEDURE
REQ'D
SKILL
LEVEL
1 I / C * R *
1 I / C
1 I * I / R *
1
1 I (1) * I (1) *
1 I / C / R *
2 I / C
2 I / C / R *
2 I / C
1 I / C *
1 I *
DAILY OR
BEFORE USE
EVERY
REFUEL
3 MONTHS
OR 90
HOURS
I *
600 HOURS
YEARLY
Page 20
20

AIR FILTER

Level 1.
Tools required: 25 - 50 mm (1 - 2 in.) Cleaning Brush
Parts required: Repower
1. Close choke (Cold Start Position [ entering the carburetor throat when the air filter is removed. Brush
accumulated dirt from air cleaner area.
2. Remove air filter cover. Brush dirt from inside cover.
3. Remove air filter and lightly brush debris from filter. Replace filter if it is damaged, fuel soaked, very dirty, or the rubber sealing edges are deformed.
4. If filter can be reused, be certain it:
• Fits tightly in the air filter cavity.
• Is installed with the original side out.
5. Install air filter cover.
TM
Tune Up Kit
]). This prevents dirt from

FUEL FILTER

Level 1.
Tools required: 200 - 250 mm (8 - 10 in.) length of wire with one end
bent into a hook, clean rag, funnel, and an approved fuel container
Parts required: Repower
TM
Tune Up Kit
DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal injury may result.
1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank.
2. Use the “fuel line hook” to pull the fuel line and filter from the tank.
3. Remove the filter from the line and install the new filter.
Page 21

SPARK PLUG

Level 2.
Tools Required: T-Wrench (combination socket wrench & screw
driver supplied with unit) Feeler gauge, preferably a wire gauge. Soft Metal Brush.
POWER BLOWER
OPERATOR'S MANUAL
21
Parts Required: Repower
IMPORTANT
Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) otherwise severe engine damage may occur.
1. Remove spark plug and check for fouling, worn and rounded center electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine.
3. Adjust spark plug gap by bending outer electrode.
4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).
TM
Tune Up Kit

COOLING SYSTEM

Level 2.
Tools required: 25 - 50mm (1 - 2 in.) cleaning brush, T-Wrench,
4 mm Hex Wrench
0.65 mm
(0.026 in.)
Parts Required: None, if you are careful.
IMPORTANT
To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area. This flow of air carries combustion heat away from the engine.
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching the cylinder.
• Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving.
Removal of cooling passage blockages or cleaning of cooling fins is considered “Normal Maintenance.” Any failure attributed to lack of maintenance is not warranted.
Cleaning Grill
1. Remove accumulated debris from intake grill between backpack frame and blower housing.
Page 22
22
Cleaning Cylinder Fins
1. Remove spark plug lead from spark plug, and remove engine cover (4 screws).
2. Clean cylinder fins (A) to allow cooling air to pass freely.
3. Install engine cover and attach spark plug lead.

EXHAUST SYSTEM

Spark Arrestor Screen
Level 2.
Tools required: Cross Head Screwdriver
Parts Required: Spark arrestor screen, Gaskets
WARNING
Do not perform maintenance on engine or muffler until engine and muffler are completely cool, otherwise serious personal injury may result.
A
IMPORTANT
Carbon deposits in muffler will cause a drop in engine output and overheating. Spark arrestor screen must be checked periodically.
1. Remove spark plug lead from spark plug, and remove engine cover (4 screws).
2. Remove spark arrestor covers (A), gaskets (B), and spark arrestor screen (C) from muffler. Replace screen if plugged with carbon deposits.
NOTE
When cleaning carbon deposit, be careful not to damage the catalytic element inside muffler.
3. Install spark arrestor screen and cover.
4. Install engine cover and attach spark plug lead.
C
B
A
Page 23
Exhaust Port Cleaning
Level 2
Tools required: Wood or plastic scraper, 4 & 5mm Hex Wrench
Parts Required: As needed: Heat Shield
1. Remove spark plug lead from spark plug, and remove engine
cover (4 screws).
2. Place piston at top dead center. Remove muffler (A) and heat
shield (B).
3. Use a wood or plastic scraping tool to clean deposits from
cylinder exhaust port.
IMPORTANT
Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port. Do not allow carbon particles to enter the cylinder.
POWER BLOWER
OPERATOR'S MANUAL
B
A
23
4. Inspect heat shield, and replace if damaged.
5. Install heat shield and muffler.
6. Tighten muffler mounting bolts (or nuts) to 95-130 in•lbf
(110-150 kgf•cm).
7. Install engine cover and attach spark plug lead.
8. Start engine, and warm to operating temperature.
9. Stop engine, and re-tighten mounting bolts to specifications.

CARBURETOR ADJUSTMENT

Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required.
High Altitude Operation
This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 1,100 feet mean sea level (MSL) (96.0 kPa and below). To maintain proper engine operation and emission compliance above 1,100 feet MSL the carburetor may need to be adjusted by an authorized ECHO service dealer.
IMPORTANT
If the engine is adjusted for operation above 1,100 feet MSL, the carburetor must be re-adjusted when operating the engine below 1,100 feet MSL, otherwise severe engine damage can result.
Page 24
24
Level 2.
Tools required: Screwdriver, tachometer (Echo P/N 99051130017)
Parts required: None.
NOTE
Do not adjust carburetor unless necessary. If you have difficulty, see your ECHO dealer.
Before Adjustment
Check that:
• Air filter is clean and properly installed.
• Spark arrestor screen is free of carbon.
• Blower pipes are installed.
1. Start engine, run at idle for one minute.
2. Complete warm up by running at full throttle for 5 minutes, operating choke twice to clear air from carburetor chambers.
3. Check idle speed and reset if necessary. If a tachometer is available, idle speed screw (A) should be set to the specifications found on Page 27 "Specifications" of this manual. Turn idle screw (A) clockwise to increase idle speed; counter clockwise to decrease idle speed.
4. Use a tachometer to adjust idle speed to specifications found on page 27.
A
Page 25

TROUBLESHOOTING

melborPkcehCsutatSesuaCydemeR
POWER BLOWER
OPERATOR'S MANUAL
TRAHCGNITOOHSELBUORT
25
deggolcreniartsleuF
roterubractaleuFroterubractaleufoN
enignE
-sknarc /drahstrats
t'nseod
trats
,snurenignE
roseidtub
tonseod
cca
etarele
ylreporp
rednilyctaleuF
dnetakrapS
eriwgulpfo
gulptakrapSkrapsoN
retlifriAytridretlifriAraewlamroNecalperronaelC
retlifleuFytridretlifleuF
tnevleuFdeggulptnevleuF
gulPkrapSnrow/ytridgulP
roterubraCtnemtsujdareporpmI
krapsoN
uF
rednilyctaleufoNroterubraCrelaedohcEruoyeeS
leufhtiwtewrelffuM
dgulP
leuf
leuf
noitarbiVtsujdA
deggolcenille
roterubraC
hcirooterutxiMleuFekohcnepO
ffohctiwspotS
melborplacirtcelE
hctiwskcolretnI
tcerrocnipagkrapS
nobrachtiwderevoC
leufhtiwdeluoF
evitcefe
seudiser/stnanimatnoCni
niseudiser/stnanimatnoC
raewlamroNecalperrotsujdadnanaelC
ecalpeR
ecalperronaelC ecalperronaelC
relaedohcEruoyeeS
retlifriaecalper/naelC
roterubractsujdA
cEruoyeeS
gulpecalpeR
relaedoh
NOothctiwsnruT
relaed
ohcEruoyeeS
relaedohcEruoyeeS
).ni620.0(mm56.ottsujdA ecalperronaelC ecalperronaelC
ecalperronaelC
metsySgnilooC
rotserrAkrapS
neercS
seodenignE
knarcton
,snurenignE
rewolb
krowt'nseod
siro
nevenu/kaew
A/NA/NmelborpenignelanretnIrelaedohcEruoyeeS
epiprewolB
/ytrid
metsysgnilooC
deggulp
rotserrakrapS deggulpneercs
deggolcepiP
esoolepiP
degamadepiP
mroNecalpeR
raewla
noitarbiVnethgiT
esusiM/raeWeca
ninoitarepodednetxE
snoitacolytsud/ytrid
sirbedfopu-dliuBgolcnU
naelC
lpeR
DANGER
Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result.
Page 26
26

STORAGE

WARNING
During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result.
Long Term Storage (Over 30 Days)
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte­nance which includes the following:
1. Store unit in a dry, dust free place, out of the reach of children.
DANGER
Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.
2. Place the stop switch in the "STOP" position.
3. Remove accumulation of grease, oil, dirt and debris from exterior of unit.
4. Perform all periodic lubrication and services that are required.
5. Tighten all screws and nuts.
6. Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburetor.
7. Remove the spark plug and pour 7cc (1/4 oz.) of fresh, clean ECHO 2-stroke engine oil into the cylinder through the spark plug hole.
A. Place a clean cloth over the spark plug hole.
B. Pull the recoil starter handle 2-3 times to
distribute the oil inside the engine.
C. Observe the piston location through the spark
plug hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there.
8. Install the spark plug (do not connect ignition cable).
9. Remove blower pipe assembly from unit.
Page 27
POWER BLOWER
OPERATOR'S MANUAL

SPECIFICATIONS

MODEL ----------------------------------------------------- PB-755SH, PB-755ST
Length ------------------------------------------------------- 380 mm (14.9 in.)
Width -------------------------------------------------------- 480 mm (18.9 in.)
Height ------------------------------------------------------- 525 mm (20.7 in.)
Weight (dry) ------------------------------------------------ 10.3 kg (22.7 lb.)
Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine
Displacement ----------------------------------------------- 63.3 cc (3.86 cu. in.)
Bore ---------------------------------------------------------- 48.0 mm (1.89 in.)
Stroke -------------------------------------------------------- 35.0 mm (1.38 in.)
Carburetor -------------------------------------------------- Walbro w/primer bulb
Ignition System -------------------------------------------- Flywheel Magneto, capacitor discharge ignition type
Spark Plug -------------------------------------------------- NGK BPMR-8Y Gap 0.65 mm (0.026 in.)
Exhaust System -------------------------------------------- Spark arrestor - catalytic muffler / muffler
Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil)
Fuel/Oil Ratio ----------------------------------------------- 50 : 1 Power Blend X
M345- FC/FD, two-stroke, air-cooled engine oil.
Gasoline ----------------------------------------------------- Use 89 Octane unleaded. Do not use fuel containing methyl
alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use alternative fuels such as E-20 or E-85.
Oil ------------------------------------------------------------ Power Blend X TM Premium Universal 2-Stroke Oil
Fuel Tank Capacity ---------------------------------------- 2.0 lit. (67.7 US fl. oz.)
Recoil Starter System -------------------------------------- Automatic Recoil Starter Centrifugal Type
Idle Speed ---------------------------------------------------2400 - 3200 (RPM)
Wide Open Throttle Speed ------------------------------- 6800 - 7300 (RPM)
Maximum Air Speed (Measured at pipe end) ---------- 329.9 KM/H (205 mph)
Average Air Volume (Measured at pipe end) ---------- 17.6 m3/min. (620 cu. ft./min.)
Sound Level at 50 ft. dB(A) scale per ANSI B175.2 ---- 74 dB(A)
TM
ISO-L-EGD (ISO/CD 13738) and J.A.S.O.
27
IMPORTANT This spark ignition system complies with Canadian ICES-002
Page 28

SERVICING I NFORMATION

PARTS
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the unit with you. You can find these numbers on the engine housing. For future reference, write them in the space provided below.
Model No. _____________ Type _________SN. ______________
/SERIAL NUMBER
SERVICE
Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your unit for Warranty service/repairs, proof of purchase is required.
ECHO CONSUMER PRODUCT SUPPORT
If you require assistance or have questions concerning the application, operation or maintenance of this product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to 4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit to help your Consumer Product Support Representative.
DEALER?
Call
1-800-432-ECHO
1-800-432-3246
or
www.echo-usa.com
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
WARRANTY REGISTRATION
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at www.echo-usa.com. Other registration options are by automated phone at 1-800-432-3246 or by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and provides a direct link between you and ECHO if we find it necessary to contact you.
ADDITIONAL OR REPLACEMENT MANUALS
Safety Manuals in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at www.echo-usa.com. Operator's and Parts Manuals are available by:
• Downloading free from www.echo-usa.com
• Purchasing from your Echo Dealer.
• Manuals are available by sending a written request stating the model number and serial number of your Echo unit, part number of the manual, your name and address, and mail to the address below.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
ECHO, INCORPORATED
400 OAKWOOD R OAD
LAKE Z URICH, IL 60047
www.echo-usa.com
(H) P04513001001/P04513999999 (T) P04213001001/P04213999999
Loading...