Echo AUDIOFIRE2, AUDIOFIRE4, AUDIOFIRE8, AUDIOFIREPre8, AUDIOFIRE12 Owner’s Manual

AUDIOFIRE2TM

AUDIOFIRE4TM

AUDIOFIRE8TM

AUDIOFIREPre8

AUDIOFIRE12TM

Owner’s Manual Version 2.2 for Macintosh

Important Safety Instructions

1. Read Instructions - Be sure to read all of the safety and operating instructions

before operating this product.

2. Retain Instructions - The safety instructions and owner's manual should be retained for future reference.

3. Heed Warnings - All warnings on your Echo product and in the Owner's Manual should be followed.

4. Follow Instructions - All operating and use instructions should be followed.

5. Moisture - Water and moisture are detrimental to the continued good health of

your Echo product. Do not install or operate your Echo product near sources of water or moisture such as sinks, damp basements, leaky roofs, etc.

6. Heat – Your Echo product should be situated away from sources of heat such as heaters or radiators.

7. Power Sources - This unit should be operated only from the type of power source indicated in this documentation or on your Echo product. If you are unsure about the type of power at your location, contact your local power company.

8. Grounding – Precautions should be taken so that the grounding capabilities of the unit are not undermined. The AudioFire 8, AudioFire Pre8 and AudioFire 12 are provided with a cord with an equipment grounding conductor and grounding plug. This plug must be plugged into an outlet that is properly installed and grounded in accordance with all local rules and ordinances. Do not modify the plug provided with the equipment. If the plug will not fit into your outlet, have a proper outlet installed by a qualified electrician.

9. Power Cord Protection – Power supply cords should be routed so that they are unlikely to be walked on or pinched by items placed upon or against them. Pay particular attention to protecting the plugs, outlets, and the point at which the cord exits your Echo product.

10. Servicing - Do not attempt to service this unit yourself, as opening the case will expose you to hazardous voltage or other dangers. All servicing should be referred to qualified service personnel.

11. Damage Requiring Service - Unplug this unit and refer it to a qualified service technician when any of the following occur:

a) Objects have fallen or liquid has spilled into the unit b) The product has been exposed to rain or water c) The product does not operate normally or when a marked change in performance is noticed d) The product has been dropped or damaged in any way

Registering your product online at http://www.echoaudio.com/support/register.php allows us to register key information so that we may handle problems faster and inform you of advance information on upgrades and other news. Thank you in advance for registering. We hope you enjoy your Echo product.

Limited Warranty

Echo Digital Audio Corporation warrants this product, when purchased at an Authorized Echo Dealer in the United States of America, to be free of defects in materials and manufacturing workmanship for a period of one year from the date of original purchase. During the warranty period Echo shall, at its option, either repair or replace any product that proves to be defective upon inspection by Echo. Final determination of warranty coverage lies solely with Echo. Echo reserves the right to update any unit returned for repair, and reserves the right to change or improve the design of the product at any time without notice.

This is your sole warranty. Echo does not authorize any third party, including any dealer or sales representative, to assume any liability on behalf of Echo or to make any warranty for Echo.

Service and repairs of Echo products are to be performed only at the factory (see below) unless otherwise authorized in advance by the Echo Service Department. Unauthorized service, repair or modification will void this warranty.

To obtain factory service:

Contact Echo Digital Audio Corporation at (805) 684-4593, 9AM to 4PM Monday through Friday (Pacific Time). If necessary, you will be given a return authorization number. Products returned without an RA number will be refused. Echo may, at its option, require proof of the original date of purchase in the form of a dated copy of the original authorized dealer’s invoice or sales receipt. Pack the product in its original shipping carton and attach a description of the problem along with your name and a phone number where Echo can contact you if necessary. Ship the product insured and freight prepaid to:

Echo Digital Audio Corporation

DISCLAIMER AND LIMITATION OF WARRANTY

Echo makes no other warranties, express, implied, or otherwise, regarding Echo products, and specifically disclaims any warranty for merchantability or fitness for a particular purpose. The exclusion of implied warranties is not permitted in some states and the exclusions specified herein may not apply to you. This warranty provides you with specific legal rights. There may be other rights that you have which vary from state to state.

In no event will Echo be liable for any lost profits, or for any con s equential, direct or indirect damages, however caused and on any theory of liability, arising from this warranty and sale.

6450 Via Real

Carpinteria, CA 93013

and AudioFire are trademarks of Echo Digital Audio Corporation.

Echo

, FireWire®, iTunes®, iMovie®, iDVD®, Mac®, Macintosh®, Mac OS®, Power Mac®, PowerBook®,

Apple QuickTime

, and GarageBand are trademarks of Apple Computer, Inc.

INTRODUCTION....................................................................................................8

HAT YOU SHOULD HAVE RECEIVED IN THE BOX.................................................8

SYSTEM REQUIREMENTS .........................................................................................9

INSTALLATION...................................................................................................10

CHECK OS X VERSION..........................................................................................10

RUN SOFTWARE UPDATE ......................................................................................10

INSTALLING THE AUDIOFIRE HARDWARE AND SOFTWARE ...................................11

CONNECTING TO THE AUDIO INTERFACE...............................................................13

SOFTWARE CONFIGURATION.................................................................................24

CONSOLE..............................................................................................................27

RUNNING THE CONSOLE........................................................................................27

AUTOMATIC FLASH UPDATE .................................................................................27

CONSOLE WINDOW ...............................................................................................27

BUS SELECT TABS.................................................................................................28

MASTER OUTPUT BUS CONTROL...........................................................................29

PLAYBACK CONTROLS ..........................................................................................29

ANALOG INPUTS....................................................................................................30

DIGITAL INPUTS (AUDIOFIRE 2, AUDIOFIRE 4 AUDIOFIRE 8 AND AUDIOFIRE PRE8)

..............................................................................................................................32

Adjusting Playback Volume.............................................................................33

Nominal Levels.................................................................................................34

SETTINGS TAB.......................................................................................................34

Sample Rate......................................................................................................35

Clock Source....................................................................................................36

Digital Mode (and AudioFire Pre8)................................................................36

ABOUT DIALOGUE BOX.........................................................................................36

Version Information.........................................................................................36

Copy Version Information to Clipboard..........................................................37

Flash Update....................................................................................................37

AUDIOFIRE 2 AND AUDIOFIRE 4 PLAYBACK ROUTING..........................................37

CONSOLE SESSIONS...............................................................................................39

CONSOLE SETTINGS AND STAND-ALONE MODE....................................................39

SYNCHRONIZING EXTERNAL DEVICES...................................................................40

CONTACTING ECHO CUSTOMER SERVICE ..............................................44

APPENDIX A: GENERAL TROUBLESHOOTING GUIDE ..........................45

APPENDIX B: AN INTRODUCTION TO DIGITAL RECORDING.............49

INDEX.....................................................................................................................56

Introduction

Thank you for choosing Echo Digital Audio. We think you’ll find your Echo product to be an extremely flexible, high-performance tool for your computerbased hard disk recording system.

What You Should Have Received in the Box

When you opened the box, you should have found the following:

 An audio interface box  Four mounting screws with collars (AudioFire 8, AudioFire Pre8 and

AudioFire 12 only)

 Two removable rack-mount brackets (AudioFire 8 only)  A FireWire cable  A MIDI and S/PDIF dongle (AudioFire 2 only)  A 4-pin to 6-pin FireWire adapter (AudioFire 2 and AudioFire 4 only)  A power cable or power adapter  A CD-ROM containing:

 Windows XP and Vista Drivers  Mac OS X Drivers  PDF Owner’s Manual

 A Quick Start Guide

Introduction

System Requirements

In order to use AudioFire 2, AudioFire 4, AudioFire 8, AudioFire Pre8 or AudioFire 12 you’ll need the following:

 An Apple brand Macintosh computer (desktop or notebook) with:

 Mac OS X (10.3.9 or later)  An unused FireWire port  A G4 or better processor (G5 recommended)  A minimum 256Mb of RAM (512Mb highly recommended)  A fast, high-capacity IDE, SCSI or FireWire hard disk drive

 Peripheral audio equipment, such as a mixer, microphones, studio monitors,

musical instruments, etc.

Introduction

Installation

To properly install your AudioFire product you will need to log in as an administrator, check your OS X version, run software update, connect the audio interface to a FireWire port and to your peripheral audio hardware and install the Console software. The following steps will guide you through installing your AudioFire product.

In order to properly install your AudioFire product you need to make sure that you log in to your Mac with an account that has administrative privileges. To verify that your account has administrative privileges, open “System Preferences” from the Dock or from the Apple menu, select “Show All”, and then select “Accounts” in the “System” section. Now, select your account from the list on the left and click on the “Security” tab. Make sure that the checkbox at the bottom labeled “Allow user to administer this computer” is checked. If your account does not have administrative access, then you will need to log out and log in with an account that does.

Check OS X Version

OS X version 10.3.9 (or later) is required use your AudioFire product. If you have a version lower than 10.3.9, your AudioFire product may not install, or may not function properly. To check your OS X version open “About This Mac” from the Apple menu. Verify that you have OS X version 10.3.9 or later. If you do not, then you will need to either purchase an upgrade or download it with Software Update.

Run Software Update

Before you install anything, you should make sure that you have the most recent updates for Mac OS X installed. This is especially important. If Mac OS X is out of date, you may not be able to use your AudioFire product at all. To do this, open “Software Update” from the Apple menu. Download and install all of the updates, including updates for software like iTunes, iDVD, iMovie, QuickTime, GarageBand, etc.

Installation

Installing the AudioFire Hardware and Software

Now that you have logged in as an administrator, checked the OS X version, and updated your software, you are ready to install your AudioFire product in your computer.

1. Install the AudioFire Console. Insert the AudioFire Install CD-ROM into your

machine. Simply drag the AudioFire Console to your Applications folder or whatever folder you prefer.

2. Once you have installed the console, locate the AudioFire interface box, the

power cable, and the FireWire cable. If you are installing an AudioFire 8, AudioFire Pre8 or AudioFire 12, securely mount the interface into your equipment rack. If you will not be mounting the box in a rack, then be sure to place the interface box in a secure location.

3. If you have AudioFire 8, AudioFire Pre8 or AudioFire 12, plug the power

cable firmly into the interface and a power socket, and then turn on the

interface by pressing the power button. If you have AudioFire 2 or AudioFire 4 your AudioFire can be powered directly through FireWire. No external power supply is needed. The DC adapter is included for users of Windows notebook computers that have only an unpowered, 4-pin FireWire connector.

4. Plug one end of the FireWire cable into the FireWire connector on the rear of

the AudioFire interface. Attach the other end of the FireWire cable to an open FireWire port on your computer. (If the connector does not match the port on your computer then you will need to get an adapter.)

5. Your Mac will automatically recognize your new AudioFire product without

any fanfare. See the “Software Configuration” section below for more info.

Installation

NOTE: You should check the driver downloads area of our website (www.echoaudio.com

) for any software updates and install them before continuing. The AudioFire hardware must be installed and powered on for the firmware update to load properly. You should also check the website periodically in the future in case any more updates are released at a later time.

6. You can now attach external audio devices to the connectors on the AudioFire

interface box. Information on attaching external devices to the audio interface box may be found in the following section: “Connecting to the Audio Interface”.

Installation

Connecting to the Audio Interface

The AudioFire 2, AudioFire 4, AudioFire 8, AudioFire Pre8 and AudioFire 12 audio interfaces contain a wide variety of connections that allow great flexibility in operation. For optimal performance, it is critical to use the appropriate cabling and connectors.

Analog Inputs and Outputs – AudioFire 2

AudioFire 2’s front panel has two analog line inputs (1 – 2), an amber power indicator light, and an 1/8” stereo headphone output jack, with a corresponding volume knob, which monitors analog outputs 3 and 4, labeled “Headphones” in the AudioFire Console. The analog inputs operate with an input impedance of 10Kohms.

AudioFire 2 has two analog line outputs on the rear panel. The input and output connections can be used with balanced or unbalanced cables via the ¼” connectors. By default, the inputs and outputs are set to receive or send a +4dBu signal.

You can switch between +4dBu and –10dBV for each individual input and output via the console software (see section below).

Connecting to the Audio Interface

Analog Inputs and Outputs – AudioFire 4

AudioFire 4’s front panel has two universal inputs (1 – 2) with meters and trim knobs, a phantom power indicator (+48v), and a power button with an amber power indicator light. There is also an 1/8” stereo headphone output jack, with a corresponding volume knob, which monitors analog outputs 1 and 2.

AudioFire 4 has two analog line inputs (3 – 4) and four analog line outputs on the rear panel. These analog inputs (3 – 4) operate with an input impedance of 10Kohms. The input and output connections can be used with balanced or unbalanced cables via the ¼” connectors. By default, the inputs and outputs are set to receive or send a +4dBu signal.

You can switch between +4dBu and –10dBV for each individual input and output via the console software (see section below).

Analog Inputs and Outputs – AudioFire 8

AudioFire 8’s front panel has two universal inputs (1 – 2) with meters and trim knobs, a phantom power switch and light (+48v), and a power button with an amber power indicator light (not shown below). There is also a ¼” stereo

Connecting to the Audio Interface

headphone output jack, with a corresponding volume knob, which monitors analog outputs 1 and 2.

AudioFire 8 has six analog line inputs (3 – 8) and eight analog line outputs on the rear panel. These analog inputs (3 – 8) operate with an input impedance of 10Kohms. The input and output connections can be used with balanced or unbalanced cables via the ¼” connectors. By default, the inputs and outputs are set to receive or send a +4dBu signal.

You can switch between +4dBu and –10dBV for each individual input and output via the console software (see section below). There are also two channel inserts on the rear panel where you can connect a serial effects device (compressor, EQ, etc.) for the universal inputs (1 – 2). The channel inserts are wired: tip = send, ring = return and sleeve = ground.

Connecting to the Audio Interface

The new AudioFire 8 (as of July 2009) now has optical S/PDIF and ADAT I/O, in addition to coaxial S/PDIF.

Analog Inputs and Outputs – AudioFire Pre8

AudioFire Pre8’s front panel has two universal inputs (1 – 2) with meters and trim knobs. Inputs 1 – 2 also have Phase, 80Hz, Pad, LoZ, DI and phantom power buttons with corresponding LEDS. In addition, there are six meters and trim knobs on the front panel for universal inputs (3-8) and a corresponding phantom power button and LED. There are also two ¼” stereo headphone output jacks wired in parallel which monitor analog outputs 1 and 2 with a corresponding volume knobs, the main volume control (Outputs 1 – 2) and the On/Off button and LED.

Connecting to the Audio Interface

The rear panel has universal inputs 3 – 8, line outputs 1 – 8, 2 channel inserts, MIDI i/o, S/PDIF i/o, ADAT i/o, BNC WordClock connectors, and two FireWire connectors.

AudioFire Pre8 Analog Inputs 1 – 2 Microphone and Line Buttons

Analog inputs 1 – 2 each have 6 associated buttons: Phase, 80Hz, Pad, LoZ, DI and +48V (phantom power).

Microphone buttons: Ø (Phase): Inverts the polarity of the signal. Useful for miking drums, etc.

80Hz: Turns on an 80Hz high pass filter to reduce low frequency rumble and

hum.

Pad: Reduces the preamp gain by 20dB to accommodate large microphone

or line level signals connected via XLR.

LoZ: Reduces the microphone preamp input impedance from 3,000 ohms to

1,000 ohm. Some microphones are designed to drive a lower impedance and will sound better when this switch is on.

+48V: Turns on phantom power.

Line button:

DI: Direct input. Increases the 1/4" input impedance from 12,000 ohms to 1

meg ohm. Useful for connecting electric guitars or other instruments needing a high input impedance. Should only be used with mono plugs.

Connecting to the Audio Interface

+ 39 hidden pages

Echo AUDIOFIRE2, AUDIOFIRE4, AUDIOFIRE8, AUDIOFIREPre8, AUDIOFIRE12 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual