!
Installation and Operation Instructions
EW2440 & EW2441 LED WORKLAMPS
ECCO’s EW2440 and EW2441 LED Worklamps feature an
aluminum heatsink housing, tough polycarbonate lens and six 3-watt
LEDs that produce a high-intensity beam. These extremely compact
lights offer all the benets of LED technology including the brightest
white light output, a long maintenance-free service life and extremely
low current consumption.
IMPORTANT! Read all instructions before installing and using. Installer: This manual must be
delivered to the end user.
WARNING!
Failure to install or use this product according to manufacturer’s recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.
1. Proper installation combined with operator training in the installation, use, care and maintenance of vehicle equipment accessories is
essential to ensure the safety of you and those you are trying to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high
current arcing, which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation are vital to the performance of this worklamp. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he can
operate the system without losing eye contact with the work area.
5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the
vehicle operator should ensure the projection of the beam is not blocked by vehicle components (i.e., open trunks
or compartment doors), people, vehicles, or other obstructions.
6. The manufacturer assumes no liability for any loss resulting from the use of this device.
SAA
NOTE: Black die cast Aluminum housing gets very hot to the touch after operating constantly for several hours.
Specications:
Voltage: EW2440: 12-24 VDC
EW2441: 12-24 VDC
Current: EW2440: 0.76A @ 12.8VDC
EW2441: 0.38A @ 12.8VDC
Weight: EW2440: 0.8 lbs.
EW2441: 0.8 lbs.
Lumens: EW2440: 1140
EW2441: 1140
Installation:
1. Set the unit face side down on a at surface.
2. Insert the M8 x 24mm hex head bolt through the slot of the
bracket, ensuring that the hex head is captured between
the louvers of the bracket.
3. Place the mounting bracket around the back of the unit,
aligning the bracket holes with the mounting holes in the
unit.
4. Place one M5 lock nut in one of the spaces provided,
making sure that the threads are facing the hole.
5. Insert the M5 x 13.5mm socket head cap screw through
both the bracket and unit holes on one side.
6. Using the 4mm hex key provided, thread the cap screw
into the lock nut. You may need to use a athead
screwdriver to hold the lock nut in place and prevent it
from turning while threading. Do not completely tighten the
assembly at this time.
7. Repeat steps 3-5 with the second lock nut and cap screw.
8. Select the mounting location for the unit. If neccessary, drill
a 9mm through hole in the mounting surface.
9. Align the unit with the mounting location, and insert the
M8 hex head bolt through the hole. Secure the unit with
the M8 lock washer and M8 nut on the back side of the
mounting location. (continued on next page)
Page 1 of 2
Worklamp
Light
5A
BLKRED
10. Position the unit in the horizontal direction, and tighten
Wiring Instructions:
the M8 nut with a wrench.
11. Position the unit in the vertical direction, and tighten the
M5 screws with the 4mm hex key.
Black Wire: Ground
Red Wire: Connect to fused power
See wiring diagram for further instruction
Electronics Controls Company “ECCO” (Manufacturer)
ECCO warrants that on the date of purchase, this product will conform to ECCO’s specications for this product (which are
available from ECCO upon request). This Limited Warranty extends for twelve (12) months from the date of purchase.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING
MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN ECCO’S INSTALLATION AND
OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.
Exclusion of Other Warranties:
ECCO MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY, QUALITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM A COURSE OF DEALING, USAGE OR TRADE PRACTICE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT AND ARE HEREBY
DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.
Remedies and Limitation of Liability:
ECCO’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR
UNDER ANY OTHER THEORY AGAINST ECCO REGARDING THE PRODUCT AND ITS USE SHALL BE, AT ECCO’S DISCRETION, THE REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE REFUND OF THE PURCHASE PRICE PAID BY
BUYER FOR NON-CONFORMING PRODUCT. IN NO EVENT SHALL ECCO’S LIABILITY ARISING OUT OF THIS LIMITED
WARRANTY OR ANY OTHER CLAIM RELATED TO THE ECCO’S PRODUCTS EXCEED THE AMOUNT PAID FOR THE
PRODUCT BY BUYER AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL ECCO BE LIABLE FOR LOST
PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF ECCO OR A REPRESENTATIVE OF ECCO HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. ECCO SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT
TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND ECCO NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.
This Limited Warranty denes specic legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages.
833 West Diamond St
Boise, Idaho 83705
Customer Service
USA 800-635-5900
UK +44 (0)113 237 5340
AUS +61 (0)3 63322444
©2013 ECCO
920-0358-00 Rev. B Page 2 of 2
www.eccosafetygroup.com
Loading...