Page 1
!
!
Installation Instructions
Reversing Camera/Monitor System
Introduction:
ECCO’s Reversing Camera System is designed to provide visual cues to help drivers avoid collisions
when backing up. A driver using a properly installed and maintained rear view system can be alerted
to potential safety hazards and thus take the appropriate action to prevent an accident. This manual
provides information about installation, function, safety, maintenance, replacement parts, and warranty.
WARNING!
Failure to install or use this product according to manufacturers recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the
safety information contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of vehicle camera systems
are essential to ensure the safety of you and those you are trying to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high
current arcing, which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation are vital to the performance of this device. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that
s/he can operate the system without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use,
the vehicle operator should ensure the projection of the signal is not blocked by vehicle components (i.e., open
trunks or compartment doors), people, vehicles, or other obstructions.
WARNING!
1. High voltage is present within the monitor. The opening of the case should be by professionals.
2. Do not watch the video while driving unless you are monitoring the rear view camera display.
IMPORTANT! Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very
common phenomenon in active matrix display technology, and doesn’t necessarily indicate any defects or
faults. Never try to repair this device by yourself. In case of any problems, please turn off the display at once
and notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modication
may lead to damage and void the warranty.
Page 2
!
CAMERA EC2015-C-Flush Mount
Image Color CMOS
NTSC: 580*540
PAL: 580*492
Voltage Requirement 12V +/-1V
Power Consumption < 1w
Lens N/A
Lens Angle 120°
Audio No audio function
Light Sensor CMOS
Infrared LEDs 10
Pigtail Connection: CAM Female 4 Pin Threaded
Housing Aluminum alloy
Mech. Vibration 10 g
Mounting Flush mount
Weight 0.74 lbs (0.3kg)
Dimensions (WxHxD) 1.69 x 1.24 x 1.10 in
43 x 31.5 x 28 mm
Operating Temp. -22°F to 158°F
IP Rating IP67
Approvals CE, FCC, RoHS
Current Consumption 0.43A
MONITOR EC4204-M - 4.3” RV Mirror
Image 4.3” LCD Color, 4:3
Controller Internal/2 camera
Voltage 12-24V
Power Consumption 3W
Mirror Imaging Yes (via menu of mirror)
Split Screen Feature No
AV Compatible No
Audio No
Contrast/Brightness Yes
Light Sensor N/A
Camera Selection 1-2 Trigger Wires
Connection: CAM Female 4 Pin Threaded
Connection (Mirror Pigtail) Male 8 Pin
Connection: CB N/A
Housing Plastic
Mounting Pedestal Bracket
Mech. Vibration 2.84 g
Weight 1.1 lbs
Dimensions (WxHxD) 11.04 x 1.20 x 3.60 in
280.33 x 30.5 x 91.52 mm
Operating Temp -4°F to 158°F
Remote Control Yes
Approvals CE, FCC, RoHS
WARNING!
To prevent accidental shock, DO NOT OPEN THE MONITOR CASE. Opening the monitor case will expose the
inside of the monitor to conditions that could adversely affect performance. Any evidence of tampering with
sealed components will void the warranty.
Wiring:
Camera 1
(left turn)
Monitor
Camera 2
(reversing)
Fuse
+VDC
-GND
Blue Wire
(left turn
lights)
Brown Wire
(reversing
lights)
Page 3
Accessories:
Color LCD Screen
Long press 3S to turn on/o
the monitor. Short press to select
CAM channels.
Brightness increase
Brightness decrease
Press to show menus or to
select the lower setting
CAM1
CAM2
1. AV and power supply cable.
2. Center mount bracket.
Parts Identication:
Basic Operation:
Connection Diagram
Black 4 pin male for Camera 1/ Camera 2.
SIngle red wire to positive power supply of DC/12-32V.
Single black wire to GND.
Single brown wire to positive power wire of back-up light.
Single blue wire to positive power wire of left light.
Black 8 pin male
Reversing Display:
1. When the blue wire is
connected to the positive wire
of the left turn light, the monitor
will automatically switch to
CAM 1 (left side camera) when
the left turn indicator is
activated.
R ed
B la c k
B ro w n
B lu e
Cam era
2. When the brown wire is
connected to the positive wire
of the back-up light, the monitor
will automatically switch to
CAM 2 (back-up camera). The
distancing grid will also be
displayed.
Page 4
Menu:
BRIGHT 50
COLOR 50
BRIGHT 50
COLOR 50
BRIGHT 50
COLOR 50
Press MENU to display the following options and settings:
1.Picture
2. Option
1. Picture: BRIGHT, CONTRAST, COLOR, AUTO DIM and SCALE ADJUST options will display on the screen as illustrated
below:
• Press M to select BRIGHT
PICTURE
CONTRAST 50
AUTO DIM OFF
SCALE ADJUST OFF
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!........................
Press to adjust the brightness level.
• When auto dim is turned on in dark environment, OSD turns into dim mode for dim setting. When auto dim is turned on / off in
bright environment, OSD displays normal mode.
PICTURE
DIM BRIGHT 40
DIM CONTRAST 45
DIM COLOR 40
AUTO DIM ON
SCALE ADJUST OFF
Dim Mode Normal Mode
PICTURE
CONTRAST 50
AUTO DIM OFF
SCALE ADJUST OFF
• Press M to select SCALE ADJUST • When the brown wire is connected to the positive wire of
back-up light, the distancing grid will be displayed
PICTURE
CONTRAST 50
AUTO DIM OFF
SCALE ADJUST OFF
Press to select OFF or for scale adjustment.
If is selected, press to adjust the scale up/down.
CAM 2
2. Option: LANG, SCALE, BLUE BACK, COLOR SYS options will display on the screen as illustrated below.
• Press M to select LANG • Press M to select COLOR-SYS
OPTION
LANG ENGLISH
SCALE ON
BLUE BACK ON
COLOR SYS AUTO
Press to select English, Deutsch, Français, Español, Português, Italiano,
Nederlands or Русский.
OPTION
LANG ENGLISH
SCALE ON
BLUE BACK ON
COLOR SYS AUTO
Press to select AUTO/PAL/NTSC
Page 5
Troubleshooting:
The symptoms described below do not necessarily mean a failure within the display. Please check the following items before you initiate
request for repair.
Symptoms Possible Causes/Solutions
No picture, no sound
No picture Check whether AV cable is properly connected
Dark picture
No color Adjust the color settings.
No reversing function (i.e.Picture)
Improper connection of automobile adapter. Use of un-authorized power supply. Power switch
is on OFF position.
Check whether brightness and contrast are adjusted correctly; Check whether the
environments temperature is too low.
The black wire of the monitor AV cable to the reversing light may be loose. The red wire from
the monitor may be loose.
Barriers Phenomena Reason Ways to Solve
Image Shaking Fix-up Bracket Release Adjust and Stabilize
No Image Poor connection or system connect cables are broken CHeck the connection of the
monitor to the camera
Image Blurring Camera lens are dirty Clean the camera lens
Image Slanting Cameras not installed in the right way Adjust the bracket of cameras
Declaration of conformity:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Loading...