Page 1
!
Installation Instructions
Camera/Monitor System
WARNING!
Failure to install or use this product according to manufacturers recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the
safety information contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices
are essential to ensure the safety of you and those you are trying to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high
current arcing, which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that
s/he can operate the system without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use,
the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open
trunks or compartment doors), people, vehicles, or other obstructions.
6. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an
intersection, driving against trafc, responding at a high rate of speed, walking on or around trafc lanes.
7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying
all laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and federal laws
and regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device.
Introduction:
The ECCO Rear Vision System is designed to provide rear of the vehicle information that may not be available to a driver relying solely
on a vehicle’s standard rear view mirror system. A driver using a properly installed and maintained ECCO Rear Vision System, in
conjunction with the standard rear view mirror system, can be alerted to potential safety hazards and thus take the appropriate action to
prevent an accident. This manual provides information about installation, function, safety, maintenance, replacement parts, and warranty.
Specications:
Camera EC2014-SVC
1/3” Sony CCD Color
Image
Voltage Requirement 12VDC
Power Consumption 3 W
Lens F=2.8mm / F=2.0
Lens Angle 120°
Audio Yes
Light Sensor Auto Switch B&W
Infrared LEDs 11 (10M Max. Visibility)
Pigtail Connection: CAM Male 4 Pin Threaded
NTSC: 510*492,
PAL: 500*580 Pixels
Camera EC2014-SVC
Housing Aluminum Alloy
Mech. Vibration 10g
Mounting Rear/Front
Weight 0.74 lbs
Dimensions (WxHxD) 2.87”x2.99”x2.60”
Operating Temp. -22°F to 158°F
IP Rating IP69K
Approvals FCC, CE/R10, C-Tick, E13
Current Consumption 250mA Max
920-5201-00 Rev. B Page 1 of 8
Page 2
!
Monitors EC5603-SVM 5.6” LCD Monitor EC7003-SVM 7” LCD Monitor
Image 5.6” LCD Color, 4:3 7” LCD Color, 16:9
Controller Internal/3 Camera Internal/3 Camera
Voltage 12/24VDC 12/24VDC
Power Consumption 5 W 6 W
Mirror Imaging Yes (via CAM switch) Yes (via CAM switch)
Split Screen Feature No No
AV Compatible No No
DVR Compatible No No
Audio Yes Yes
Contrast/Brightness Yes Yes
Light Sensor Day/Night Auto Dim Day/Night Auto Dim
Camera Selection 1-3 Via Trigger Wires 1-3 Via Trigger Wires
Connection: CAM Female 4 Pin Threaded Female 4 Pin Threaded
Connection (Monitor Pigtail) Male 13 Pin Male 13 Pin
Connection: CB N/A N/A
Housing Plastic Plastic
Mounting
Mech. Vibration
Weight 2.67 lbs 3.34 lbs
Dimensions (WxHxD) 6.32”x4.52”x1.07” 7.28”x5.07”x1.06”
Operating Temp -4°F to 158°F -4°F to 158°F
Remote Control Ye s Ye s
Approvals FCC, CE/R10, C-Tick, E13 FCC, CE/R10, C-Tick, E13
Permanent - HD (2 bracket options
provided)
Pedestal Bracket - 3g
Cradle Bracket - 8g
Permanent - HD (2 bracket options
provided)
Pedestal Bracket - 3g
Cradle Bracket - 8g
Installation, Wiring and Function
Caution! When drilling into any vehicle surface, make sure that the area is free from any electrical wires, fuel lines,
vehicle upholstery, etc. that could be damaged.
Notes:
1. Larger wires and tight connections will provide longer service life for components. For high current wires it is recommended
that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation
displacement connectors (e.g., 3M Scotchlock type connectors)
2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to
reduce voltage drop. High ambient temperatures (e.g., under-hood) will signicantly reduce the current carrying capacity of
wires, fuses, and circuit breakers. All wiring should conform to the minimum wire size and other recommendations of the
manufacturer and be protected from moving parts and hot surfaces. Looms, grommets, cable ties, and similar installation
hardware should be used to anchor and protect all wiring.
3. Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to protect the
wiring and devices.
4. Particular attention should be paid to the location and method of making electrical connections and splices to protect these
points from corrosion and loss of conductivity.
5. Ground termination should be only be made to substantial chassis components, preferably directly to the vehicle battery.
6. Circuit breakers are very sensitive to high temperatures and will “false trip” when mounted in hot enviroments or operated
close to their capacity.
920-5201-00 Rev. B Page 2 of 8
Page 3
Installation:
13 PIN FEMALE 13 PIN MALE
CAM 3
CAM 2
CAM 1
Brown Trig. Wire CAM 3
Blue Trig. Wire CAM 2
White Trig. Wire CAM 1
Black (Ground) -
Red (Power) +
2A INLINE FUSE SUPPLIED
Camera Model EC2014-SVC
Important! Mount the camera at a location that provides the best view of the area immediately behind the vehicle.
Generally, mounting locations toward the top of the vehicle provide the best eld of view. Lower mounting locations reduce
the eld of view and increase the likelihood of damage from road spray.
1. Find an appropriate location for installation.
2. Drill holes according to the size of U-bracket and x the U-bracket.
3. Drill a 3/4” (19mm) hole next to U-bracket.
4. Install the camera and sun-visor on U-bracket.
5. Connect the camera tail with the extension cable from inside the vehicle.
6. Loosen the hex head screws and adjust the camera’s position to get the best view angle in the monitor.
Figure 1
Wiring:
EC2014-SVC
Important! Waterproof all connections whether inside or outside the vehicle by using sealant and wrapping with
insulation tape. Wrap tape tightly, overlapping by one-half widths so there are no gaps.
Figure 2
920-5201-00 Rev. B Page 3 of 8
WIRING DEFINED
Page 4
!
Monitors:
Models EC5603-SVM and EC7003-SVM
WARNING!
To prevent accidental shock, DO NOT OPEN THE MONITOR CASE. Opening the monitor case will expose the
inside of the monitor to conditions that could adversely affect performance. Any evidence of tampering with
sealed components will void the warranty.
Important! Do not expose the monitor to water, it is not waterproof. Any water that leaks into the monitor could cause
extensive damage.
Installation:
EC5603-SVM
Installation instruction of using U-support bracket
1. Select suitable position on vehicle and x the U-support bracket with screws (Figure 3)
2. Fix the monitor to the U-support bracket with angle adjustment screws and adjust the view angle of the monitor (Figure 4)
3. Put on the sun-visor and connect the monitor with the AV and power supply conversion cable (Figure 5)
Figure 3 Figure 4
Figure 5
920-5201-00 Rev. B Page 4 of 8
Page 5
Installation instruction of using base support
1. Select suitable position on vehicle and x the base support. (Figure 6)
2. Fix the monitor to the base support and adjust the view angle. (Figure 7)
3. Put on the sun-visor and connect the monitor with the AV and power supply conversion cable (Figure 8)
Stick the base
support onto the
vehicle
Figure 6
Figure 7
Figure 8
920-5201-00 Rev. B Page 5 of 8
Page 6
Installation:
EC7003-SVM
Installation instruction of using U-support bracket
1. Select suitable position on vehicle and x the U-support bracket with screws (Figure 9)
2. Fix the monitor to the U-support bracket with angle adjustment screws and adjust the view angle of the monitor (Figure 10)
3. Put on the sun-visor and connect the monitor with the AV and power supply conversion cable (Figure 11)
Figure 9 Figure 10
Figure 11
920-5201-00 Rev. B Page 6 of 8
Page 7
Installation instruction of using base support
1. Select suitable position on vehicle and x the base support. (Figure 12)
2. Fix the monitor to the base support and adjust the view angle. (Figure 13)
3. Put on the sun-visor and connect the monitor with the AV and power supply conversion cable (Figure 14)
Stick the base
support onto the
vehicle
Figure 12
Figure 14
Figure 13
920-5201-00 Rev. B Page 7 of 8
Page 8
Manufacturer Limited Warranty and Limitation of Liability:
Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specications
for this product (which are available from the Manufacturer upon request), and Manufacturer further warrants
that this product is free from defects in materials and workmanship. This Limited Warranty extends for
1 year/12 months from the date of purchase. Other warranties may apply, call Manufacturer for details.
Manufacturer will, at its discretion, repair or replace any product found by the Manufacturer to be defective
and subject to this Limited Warranty.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE,
NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR
OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES
SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED
WARRANTY.
ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT WHICH MAY HAVE BEEN MADE BY
SALESPEOPLE, DEALERS, AGENTS OR OTHER MANUFACTURER’S REPRESENTATIVES DO NOT CONSTITUTE
WARRANTIES. THIS LIMITED WARRANTY MAY NOT BE AMENDED, MODIFIED, OR ENLARGED EXCEPT BY
A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICIAL OF MANUFACTURER WHICH EXPRESSLY
REFERS TO THIS LIMITED WARRANTY.
Exclusion of Other Warranties:
MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES
FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL
NOT APPLY TO THE PRODUCT. BUYER’S SOLE AND EXCLUSIVE REMEDY IN CONTRACT, TORT, OR UNDER
ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE THE
REPLACEMENT OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE.
Limitation of Liability:
IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER
CLAIM RELATED TO THE MANUFACTURER’S PRODUCTS, MANUFACTURER’S LIABILITY FOR DAMAGES SHALL
BE LIMITED TO THE AMOUNT PAID FOR THE PRODUCT AT THE TIME OF THE ORIGINAL PURCHASE. IN NO
EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR
LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED
UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER
CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY
WITH RESPECT TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER
ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION
WITH SUCH PRODUCT.
This Limited Warranty denes specic legal rights. You may have other legal rights which vary from state to state. Some
states do not allow the exclusion or limitation of incidental or consequential damages.
833 West Diamond St
Boise, Idaho 83705
Customer Service
USA 800-635-5900
UK +44 (0)113 237 5340
AUS +61 (0)3 63322444
www.eccogroup.com
920-5201-00 Rev. B Page 8 of 8
Loading...