ECARE ELECTRONICS PET619S User Manual

Training Manual

General Training Tips

EN

V20170222 EN FR

Table of Contents:

Important Safety Information

Important Safety Information....................................................................... 2

Components.............................................................................................. 3

How the dog training system works?.............................................................4

Features....................................................................................................4

Key Definitions...........................................................................................5

Remote Transmitter.................................................................................... 5

Collar Receiver...........................................................................................6

Operating Guide.........................................................................................6

Step 1 Prepare the Remote Transmitter and Receiver Collar................... 6–

Step 2 – Pairing Collar Receiver to Transmitter........................................ 7

Step 3 Test the Training System Functions.............................................8 –

Step 4 – Assemble and Fit the Collar Receiver........................................10

Step 5 Re-thread the collar ...................................................................11–

Frequently Asked Questions......................................................................12

Troubleshooting.......................................................................................13

FCC Notice...............................................................................................14

LIMITED ONE-YEAR WARRANTY..............................................................15

IPETS CUSTOMER SERVICE......................................................................15

WARNING: NOT FOR AGGRESSIVE DOGS. Do not use this product if your dog
is aggressive, or if your dog is prone to aggressive behavior, Aggressive dogs can
cause severe injury and even death to their owner and others. If you are unsure
whether this product is appropriate for your dog, please consult your veterinarian
or certified trainer.

CAUTION:

Risk of skin damage: Please read and follow the instructions carefully in this guide,
Proper fit of the collars is important because a loose collar may cause inconsistent
performance. A collar worn for too long or made too tight on the pet's neck may
cause skin damage, ranging from redness to pressure ulcers (commonly known
as bedsores). These collars can cause pressure necrosis if used incorrectly and
is often misidentified as burns.

Avoid leaving the collar on the dog for more than 12hours per day.
When possible reposition the collar on the pet's neck every 1 to 2hours.

Check the fit to prevent excessive pressure, and it is okay to trim any excess
strap length.

Never connect a lead to the electronic collar because it may cause excessive
pressure on the contacts.

Wash the dog's neck area and contacts of the collar weekly with a damp cloth.
Examine the contact area daily for signs of a rash or a sore.

If a rash or sore is found, discontinue use of the collar until the skin has healed.
If the condition persists beyond 48 hours, see your veterinarian.

These steps will help your pet safe and comfortable. Millions of pets are comfortable
while wearing stainless steel contacts. Some pets are sensitive to contact pressure.
You may find after some time that your pet is very tolerant of the collar. If so you
may relax some of these precautions. It is important to continue daily checks of
the contact area. If redness or sores are detected, discontinue use until the skin
has fully healed.

Thank you for choosing the iPets brand! You and your pet deserve a companionship
that includes memorable moments and a shared understanding together. Our
mission is to ensure your pet's safety by providing you the tools and techniques
to successfully train your pet. Should you have any queries, please contact our
customer service.

NOTE: Please charge before using the product.

1 2

Components:

How the dog training system works?

iPets products are reliable, effective, and comfortable for large or small dogs.
The system assists in controlling your dog without a leash in a range up to 330
yards away! Instantly send a signal from the Remote Transmitter, which activates
your dog's Collar Receiver. The dog will receive an annoying but safe, harmless
stimulation. With correct, consistent use of this product, the dog will associate his
misbehavior with your corrections, and soon enough, you will have a well-trained
dog. This particular model features adjustable levels of stimulation, enabling the
user to tweak accordingly to the dog's temperament, removing the ri sk of over
stimulation.

Features

Rechargeable Remote Transmitter and Collar Receiver.
Waterproof Collar Receiver.
100 intensity levels of Vibration.
100 intensity levels of Static Shock.
Standard Tone.
Easy to use, adjustable Intensity Dial.
Simple, ergonomic design layout.
Quick and straightforward pairing process.
Range of 330 Yards.
Capable of simultaneous control of two dogs (extra receiver is purchasable).
Adjustable TPU strap to accommodate any size of dog.
Auto-off feature to conserve power when not in use to extend battery life for

transmitter.

3

4

Key Definitions

Collar Receiver

Antenna

Indicator Light

Stimulation Button

Vibration Button

Sound Button

Intensity Dial

Charging Port

Toggle Switch

Remote Transmitter

1. Antenna: Transmits signal from Remote Transmitter to the Collar Receiver.

2. Indicator Light: Flashes green when any of the stimulation buttons

Will blink red if battery power is low to indicate the transmitter needs recharging.

3. Stimulation Button: Delivers electronic pulse stimulation to a Collar Receiver,
depending on the position of the Toggle Switch.

4. Vibration Button: Delivers vibration to a Collar Receiver, depending on the
position of the Toggle Switch.

5. Sound Button: Delivers a sound to a Collar Receiver, depending on the position
of the Toggle Switch.

6. Intensity Dial: Rotate the dial to adjust the level of vibration or static shock
stimulation from 0 to 100.

7. Toggle Switch (Dog Selection): Switches control between Collar Receiver 1
or Collar Receiver 2 (Dog 1 or Dog 2).

8. Charging Port: Charges the battery of the Remote Transmitter when connected
to a power source.

are pressed.

Contact points

Charging Port

ON/OFF Button

Indicating Light

1. Contact points: Covers the electrodes, and through them electronic
stimulation is del ivered.

2. ON/OFF Button: Powers on/off the Collar Receiver and used for Pairing or
Synch ronization of the Collar Receiver to the Remote Transmitter.

3. Charging Port: Charges the battery of the Collar Receiver when connected to
a power source.

4. Indicating Light: Flashes green when any of the stimulations are pressed.
Will blink red if the battery power is low to indicate the Collar Receiver needs
recharging.

pulse

Operating Guide

Step

1

Prepare the Remote Transmitter and Receiver Collar:

Charge the Remote Transmitter and Receiver Collar

1. Uncover the Charging Port by lifting the rubber cover.

2. Insert the charging connector into the Charging Port.

3. Plug the charger into a standard wall outlet.

4. A solid red light will appear on the Indicator Light, indicating charging
is occurring.

5. Once charging is complete, the solid red light will turn to a solid green
light.

6. Remove the charging connector, and replace the rubber cover to protect
the Charging Port.

5

6

If the Receiver Collar has no response when you press the Y button, and
the Indication light of the Receiver Collar is not on either, you can shake
Receiver Collar or force the dog to move, and the indication light of the
Receiver Collar will show green, which means the Receiver Collar is
activate and will take a signal from the remote transmitter.

Step

2

Note: Before first use, charge the Remote Transmitter and Receiver Collar
until completion.

Powering on and off the Remote Transmitter

There is no need to turn off the transmitter. When no button has been
pressed on transmitter, the unit turns off automatically. Press any button
and the transmitter will power back on automatically.

Powering on and off the Collar Receiver

Press the ON/OFF button on the receiver to power the unit on or off. When
the receiver is powered on, the indicating light will flash green.

Pairing Collar Receiver to Transmitter

Note: Transmitter and receiver are pre-paired when leaving our

manufacturing facility. In case the pairing is not established or you would
like to repair the units, please follow the instructions below:

1. Power on the Collar Receiver by pressing the ON/OFF button on the
Collar Receiver.

2. Press and hold the ON/OFF button for about 3 seconds until a beep
sounds, and the indicating light will begin to flash quickly.

3. Press any button on the transmitter once the Collar Receiver beeps.
When the Remote Transmitter and Collar Receiver are paired successfully
the indicating light will stop flashing quickly.

4. If needing to pair a second Collar Receiver, follow the same steps but
first push your Toggle Switch in the other direction.

Step

3

Test the Training System Functions

The testing methods will help determine whether the training system is
functioning as intended and will also teach you how to operate the system.
Please ensure that the pairing process is complete before attempting to
test the functionality.

Testing the Electronic Pulse Stimulation
Electronic Pulse Stimulation Tester

In your package that you received, you will find a clear almost translucent
plastic piece that has a light bulb/fuse in the middle of it. This is your
Electronic Pulse Stimulation tester. This component DOES NOT attach
to the Collar Receiver by any means and is only for testing the static shock
mode. To test the Electronic Pulse Stimulation, follow these steps:

1. Put the test light over the Electrodes of the Collar Receiver you wish
to test.

2. Ensure the Toggle Switch is in the correct position for the Collar Receiver
you're testing.

3. Adjust the Intensity Dial off of 100.

4. Press the Static Shock Button on your Remote Transmitter.

5. If done correctly, the test bulb should flash orange indicatin g the

electro n i c pulse stim u l a t i o n is ope r a t i n g correctly.

Note:

The receiver collar will go into deep sleep if no operation for 5 minutes,
and any movement by the dog will activate the receiver.

7

(Figure 3-1)

8

Note: If wanting to test the shock function on yourself, please ensure your
finger or hand is across both contact points to ensure the connection
is complete. Otherwise, user will feel no stimulation.

Testing the Vibration Functions

1. Ensure the Toggle Switch is in the correct position for the Collar Receiver
you're testing.

2. Adjust the Intensity Dial off of 100.

3. Press the Vibration Button on your Remote Transmitter.

4. If done correctly, the Collar Receiver will vibrate.

Step

4

Assemble and Fit the Collar Receiver

Attaching the Contact Points

In your package that you received, you will find 1 set of contact points.
These contact points are screwed onto the receiver so that the points
can effectively contact the dogs skin without hair/fur interfering with the
connection.

Attaching the Collar Strap to the Collar Receiver

The Collar Receiver attaches to the Collar Strap by sliding through the
tabs on each side and going wrapping around the back of the Collar
Receiver. To accomplish this correctly, please view the diagram below:

(Figure 3-2)

Testing the Sound Functions

1. Ensure the Toggle Switch is in the correction for the Collar Receiver
you're testing. Press the Sound Button on your Remote Transmitter.

2. If done correctly, the Collar Receiver will emit sound.

Fitting the Collar Receiver

Important: The proper fit and placement of the Collar Receiver is essential
for effective training. The electrodes must have direct contact with the
dog's skin.

(1) To fit the Collar Receiver, attach the Collar Strap to the Receiver.

(2) With the dog standing in front of you, place the Collar Receiver around
the dog's neck, so the receiver box and Contact Points are on the underside
of your dog's neck, making direct contact with the dog's skin. If direct
contact is not possible, shaving some fur away, to ensure good contact
is recommended.

9

(Figure 3-3)

10

(3) Fasten the collar strap. The fit should be snug, but not taut. A finger
should be able to be placed beneath the collar strap when around th e
dog's neck.

(4) Allow the dog to wear the Collar Receiver for several minutes and
check the strap again. The dog will soon become more familiar with the
Collar Receiver, so it is crucial to ensure the fit comfortable and flattering.

CAUTION: RISK OF SKIN DAMAGE

For comfort, safety and effectiveness of this product please check
the fit of the dog's collar frequently. If observing any skin irritation,
immediately discontinue use of the collar for a few days. If the skin
condition persists beyond 48 hours, consult a veterinarian. These
collars can cause pressure necrosis, commonly known as bed sores,
if used incorrectly and is often misidentified as burns.

Do not attach a leash to the collar, which can result in squeezing the
Contact Points too tightly against your dog's neck.

The design of the Collar Receiver discourages constantly wearing
the device. iPets recommends the collar not be worn for more than
12 hours out of every 24-hour period.

Most dogs feel uncomfortable when wearing the collar for the very
first time. Do not use any functions until the dog is accustomed to
the collar.

iPets suggests giving the dog, the vibration stimulation before
following it with a static shock. After training for a while using this
method, the dog will be aware that after vibration comes a static
shock. Vibration will act as a warning, and static shock only acts as
a menace that might be necessary sometimes.

Step

5

Re-thread the collar

Regular Maintenance

Ensure Contact Points are not too tight on a weekly basis.
Rinse the Contact Points with alcohol on a weekly basis.

Check the dog's neck for irritation and wash the dog's neck on a
weekly basis.

Feel free to cut any additional Collar Strap material if it's too long
for your dog.

Frequently Asked Questions:

How old does the dog have to be before using the system?

Your dog should have learned basic obedience commands such as, “sit” or “stay.”
The Collar Receiver might be too large for dogs under 15lbs.

Once my dog completes training and is been obeying my commands, will he
have to wear the collar?

Probably not, but you may try to reinforce training with the collar.

Can I use the iPets rechargeable training collar with more than one dog?

Yes, you just need to purchase another Collar Receiver for the system.

Is the Collar Receiver waterproof?

Yes, but always ensure that the Rubber Cover seals the Charging Port.

Can I replace the Collar receiver with another kind of collar?

No.

Can I attach a leash to the Collar Receiver?

No, this can result in pulling the Contact Points too tightly against the dog's neck.
Attach a leash to a separate, nonmetallic collar or a harness. Ensure the extra
collar does not put pressure on the Contact Points.

11

How long can I leave the Collar Receiver on my dog?

The design of the collar discourages constant wearing. We recommend not having
the dog wear the collar for more than 12 hours out of every 24-hour period.

12