ECA Intercept 2 Installation Sheet

Intercept 2
Installation Sheet
NOTE: DO NOT ATTEMPT TO INSTALL THE INTERCEPT PRIOR TO READING THESE INSTRUCTIONS Step 1. Prepare table per instructions on separate sheet. Be sure to retain portion of cut out tabletop if it will become
the finished top of the INTERCEPT 2.
Step 2. Unpack the INTERCEPT 2, being careful not to damage any part, and check to ensure that no items were
damaged during shipping. Review parts list to be sure all parts are pre sent.
Step 3. TABLE THICKNESS ADJUSTMENT - The INNER PAN ASSY has four (4) adjustable mounting flanges that
can be set for your specific table thickness between .656” - 1.625”. The flanges come set for the thinnest table. To change the flanges remove the lock nuts (2 per flange) and move the flanges to the hole that correspond s with the table thickness that the INTERCEPT 2 will be mounted in.
Table Thickness
1.375” – 1.625” Table Thickness
1.125” – 1.375”
Table Thickness .83” – 1.125”
Table Thickness .656” - .83”
Tighten the lock nuts; be sure all of the flange tops are at the same height Step 4. TABLE CUTOUT MOUNTING - Attach CUTOUT PIECE, from table preparation, to top of MAIN HOUSING.
The 8 pilot holes should line up. From underside of the INNER PAN, insert screws (use magnetic screwdriver) and secure the CUTOUT PIECE to the MAIN HOUSING.
Main Housing
Cutout Piece
InnovativePowe r + DataSolution
ECA • 10 Mountain View Drive • Shelton, CT 06484 • Phone: 1-800-521-3175 • Fax: 203-924-6687
www.electri-cable.com
9065-0002 RevF
Top of Inner Pan Flange
Screws Qty 8
Inner Pan Assembly
1
Step 5. INNER PAN MOUNTING - Place the INNER PAN ASSY. to the underside of the table and secure with twelve
(12) #10 X ½ screws provided, use pilot holes to ensure proper alignment. NOTE: USE CAUTION WHEN POSITIONING THE INTERCEPT 2 ON THE TABLE, ENSURE THAT THE GRAIN OF THE CUTOUT PIECE MATCHES THE TABLE.
#10 x ½ Screws Qty 12
(If other than included screws are used, be careful not to pierce finished side)
Step 6. OUTER PAN MOUNTING - Position the OUTER PAN ASSY. below the mounted INNER PAN ASSY. Connect
the power feed (Twist-Lock), and motor feed wires (RED and BLACK) from the OUTER PAN ASSY to the MAIN HOUSING Twist-Lock and motor. Be sure to feed the wire through the cutout in the OUTER PAN. Attach the OUTER PAN ASSY to the underside of table with six (6) #10 X ½ screws provided. Use pilot holes to ensure proper alignment.
#10 x ½ Screws Qty 6
(If other than included screws are used, be careful not to pierce finished side)
Step 7. Plug the ROCKER SWITCH ASSY onto the cable utilizing the 4-pin connector, plug in the unit and test for
proper operation. By pressing the “Raise” side of the ROCKER SWITCH the INTERCEPT 2 should elevate and lock at top. By pressing the “Lower” side of the ROCKER original, retracted, position.
Underside of
Table
Innov ativePow er + DataSolution
SWITCH the INTERCEPT 2 should return to the
ECA • 10 Mountain View Drive • Shelton, CT 06484 • Phone: 1-800-521-3175 • Fax: 203-924-6687
www.electri-cable.com
9065-0002 RevF
Twist-Lock
Connector
Inner Pan Assembly
Underside of
Table
4-Pin Connector
Outer Pan
Assembly
Rocker Switch Assembly
Inner Pan Assembly
2
If INTERCEPT 2 doesn’t operate, check:
1. INTERCEPT 2 is plugged into a powered outlet.
2. Twist-Lock connector between Power Unit and MAIN HOUSING is completely locked into place by twisting.
3. Motor connector is completed latched.
Step 8. ROCKER SWITCH MOUNTING – Mount the ROCKER SWITCH ASSY. in a convenient location using #10 x
½ screws provided. Secure wire as needed.
Step 9. VOICE/DATA CONNECTIONS - Raise the INTERCEPT 2, remove the 4 VOICE/DATA Plates, using the
special tool provided, and snake the VOICE/DATA wires up through the OUTER PAN and through the 2 SHUTTER BUSHINGS in the bottom of the MAIN HOUSING. Wires should be dressed to move freely up and down with the movement of the MAIN HOUSING. This step can be done before mounting the INTERCEPT 2 however, be sure all wires are run through the cutout in the OUTER PAN before completing step 5.
Congratulations. Enjoy your Intercept 2.
PARTS LIST
Inner Pan Assembly Qty 1 Outer Pan Assembly Qty 1 Rocker Switch Assembly Qty 1 Table Brush Qty 4 7/64 Allen Wrench Qty 1 #10 X ½ Pan Head Screw Qty 20 #4 X ½ Pan Head Screw Qty 12 Table Preparation Instructions Qty 1 Installation Instructions Qty 1 Housing Adjustment Instructions Qty 1
Innov ativePow er + DataSolution
ECA • 10 Mountain View Drive • Shelton, CT 06484 • Phone: 1-800-521-3175 • Fax: 203-924-6687
www.electri-cable.com
9065-0002 RevF
3
Loading...