E&C Cheerups 600, Cheerups 1000 Installation Manual And Operators Instructions

Line Interactive UPS

Cheerups

Cheerups

Cheerups

h

e sC

e

r

up

he sC

erup

An ISO 9001:2008 Company

Installation and Operation Manual

Package Contents

Page 2

You should have received the following items inside of package:

- UPS Unit

- Installation and Operation Manual

- Communication cable (only for the model with USB/RS-232 port)

Product Overview

Front View:

RS-232

RS-232

USB

USB

IN OUT

1

1

7

3

4

2

5

6

5

4

3

2

8

5

600 Model

w / RS-232

600 Model

w / USB

1000 Model

1

2

3

4

5

Output receptacle

AC input

RS-232 port (option)

USB port (option)

Circuit breaker (option)

6

7

8

RJ-11 port

RJ-45 port

RJ-11 or RJ-45 selections

Back View:

1

2

Power switch

UPS status LED
AC mode : green light
Battery mode : green flashing

Power switch

Fault LED : red light

Battery mode LED : yellow light

AC mode LED : green light

Installation and Operation Manual 1.0

NOTE: Before installation, please inspect the unit. Be sure that
nothing inside the package is damaged.

Placement & Storage Conditions
Install the UPS in a protected area that is free of excessive dust and adequate air
flow. Please place the UPS away from other units at least 20cm to avoid interference.
Do NOT operate the UPS where the temperature and humidity is outside the specific
limits. (Please check the specs for limitations.)

Installation & Initial Startup

Connect to Utility and Charging

Plug in the AC input cord to the wall outlet. For
the best results, suggest to charge the battery
at least 6 hours before initial use.
The unit charges its battery while connecting to
the utility.

6 hours

20 cm 20 cm

Connect Modem/Phone or Network for Surge Protection
(Only for the model with RJ-11/RJ-45

Connect a single modem/phone line into surge-protected “IN” outlet on the back panel
of the UPS unit. Connect from “OUT” outlet to the computer with phone line cable.

Connect Communication Cable (Only for the model with USB/RS-232 port)

To allow for unattended UPS shutdown/start-up and status monitoring, connect the
communication cable one end to the USB/RS-232 port and the other to the
communication port of your PC. With the monitoring software installed, you can
schedule UPS shutdown/start-up and monitor UPS status through PC.

CAUTION: NEVER connect a laser printer or scanner to
the UPS unit. This may cause the damage of the unit.

Turn On/Off the Unit

Turn ON the UPS unit by pressing the power switch. Turn OFF the UPS unit by pressing
again the power switch.

Cold Start Function

When the UPS is off and there is no power utility, it’s still possible to cold start the UPS
unit to power the loads.

3

Page 3

Installation and Operation Manual 1.0

Important safety Warning

(SAVE THESE INSTRUCTIONS)

CAUTION! To prevent the risk of fire or electric shock, install in a

temperature and humidity controlled indoor area free of conductive
contaminants. (See the specifications for the acceptable temperature and
humidity range.)
CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS’
cooling vents and avoid exposing the unit to direct sunlight or installing the
unit near heat emitting appliances such as space heaters or furnaces.
CAUTION! Do not attach non-computer-related items, such as medical
equipment, life-support equipment, microwave ovens, or vacuum cleaners to
UPS.

CAUTION! Do not plug the UPS input into its own output.
CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do

not place beverages or any other liquid-containing vessels on or near the unit.
CAUTION! In the event of an emergency, press the OFF button and
disconnect the power cord from the AC power supply to properly disable the
UPS.

CAUTION! Do not attach a power strip or surge suppressor to the UPS.
CAUTION! If the UPS is with metal chassis, for safety purpose, grounding is

a must during UPS installation in order to reduce leakage current below 3.5A.
Attention hazardous through electric shock. Also with disconnection of this
unit from the mains, hazardous voltage still may be accessible through supply
from battery. The battery supply should be therefore disconnected in the plus
and minus pole at the quick connectors of the battery when maintenance or
service work inside the UPS is necessary.
CAUTION! Servicing of batteries should be performed or supervised by
personnel knowledgeable of batteries and the required precautions. Keep
unauthorized personnel away from batteries.
CAUTION! When replacing the batteries, use the same number and type of
batteries.

CAUTION! Internal battery voltage is 12Vdc. Sealed, lead-acid, 6-cell battery.
CAUTION! Do not dispose of batteries in a fire. The battery may explode. Do

not open or mutilate the battery or batteries. Released electrolyte is harmful
to the skin and eyes.
CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray
detergent.
CAUTION! A battery can present a risk of electric shock and high short
circuit current. The following precaution should be observed before replacing
batteries:

1) Remove watches, rings, or other metal objects.

2) Use tools with insulated handles.

3) Wear rubber gloves and boots.

4) Do not lay tools or metal parts on top of batteries.

5) Disconnect charging source prior to connecting or disconnecting batteries
terminal.

4

Page 4

Installation and Operation Manual 1.0

Problem Probable Cause Solution

Low battery

Battery fault

UPS is not turned on

UPS is overload

UPS is overload Remove some critical load
Battery voltage is too low

Power cord is loose

No LED display on
the front panel

Charge the UPS at least 8
hours

Replace the battery with the
same type of battery

Press te power switch again
to turn on the UPS

Alarm continuously
sounds when the
mains in normal

Remove some loads first.
Before reconnecting
equipment, please verity
that the load matches the
UPS capability specified in
the specs

When power fails,
backup time is
shorten

Charge te UPS at least 8
hours

Battery defect. It might be
due to high temperature
operation environment, or
improper operation to
battery

Replace the battery with the
same type of battery

The mains is normal
but LED is flashing

Reconnect the power cord
properly

Trouble Shooting

6

Use the table below to solve minor problems.

Software Download & Installation

(Only for the model with communication port)

5

Please follow steps below to download and install monitoring software:

1. Go to the website http://www.power-software-download.com

2. Click viewPower software icon and then choose your required Operating System to
download the software

3. Follow the on-screen instructions to install the software

4. When your computer restarts, the monitoring software will appear as an orange
plug icon located in the system tray, near the clock.

Page 5

Installation and Operation Manual 1.0

Specification

7

Page 6

Installation and Operation Manual 1.0

Page 7

Warranty Introduction:

Electronics & Controls Power Systems Pvt. Ltd ("E&C") warrants that its products are free from
defects in material and workmanship. During the warranty period, if the product fails under normal
use in the recommended environment due to improper workmanship or materials, E&C will repair or
replace the product with a comparable product.

This warranty is valid for a specific period from the date of purchase for which Proof of date of
purchase is required. E&C Engineer will inspect the product and make a decision regarding repair or
replacement. E&C reserves the right to provide a functional equivalent, or refurbished replacement
product.

Limitation:

This warranty does not apply to product failure due to accident, abuse, mishandling, improper
installation, alteration, acts of nature, improper usage, problems due to electrical power and product
service and repaired by anyone other than E&C. Burnt components are not covered under this
warranty.

Reduced Battery life or backup time due to improper or lack of charging of the battery is not covered
under this warranty.

In addition to the above, opening or tampering with the product casing, or any Physical damage,
abuse or alteration to the product's surface, including all Warranty, Quality stickers, Product serial or
electronic number will also void the Warranty.

E&C will not be liable for damages resulting from a third party device that causes the Product to fail.
E&C shall in no event be liable for any consequential, indirect, or incidental damages, lost profits, lost
business, investments, lost goodwill, or interference with business relationships as a result of lost
data.

This warranty extends only to the original purchase and is non-transferable.

Warranty Period:

To Obtain warranty service, customer must provide original proof of purchase or
invoice. In addition, the warranty card should be sent to the manufacturer at the address provided on

the Warranty Card.

Product : UPS (Uninterrupted Power Supply)
Service Type : Onsite / Carry-In (Service Center)
Period : 1 Year (for UPS & Battery)

Warranty Procedure:

a. To Log a call to the E&C Centre for a Carry-In or an on-site warranty service, you must contact

Nearest Service Center or our customer care number 080-2837 7120/21. Service Centers' list is
enclosed herewith.

b. Invoice copy issued by the Retailer/Reseller to the End user containing product serial number and

date of purchase is required to validate the warranty period.

c. After validating the warranty status, service centers will carry out ONSITE repair / replacement.

Onsite service will be provided by the nearest existing service center.

d. All Customer calls will be responded within 48 Hours of call logging, from the nearest service center

available.

e. DOA (Dead on Arrival) units will be replaced if failed within 7 days from the date of purchase and

should be supported by Reseller/Retailer invoice to the customer.

f. This Warranty is only applicable for products bought and sold in India.

* Terms and Conditions are subject to change without notice.

NOTWITHSTANDING ANYTHING ELSE IN THIS POLICY OR OTHERWISE, WD WILL NOT BE LIABLE WITH RESPECT TO
THE PRODUCTS UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY
(I) FOR ANY AMOUNT IN EXCESS OF THE PURCHASE PRICE FOR THE DEFECTIVE PRODUCT OR (II) FOR ANY GENERAL,
CONSEQUENTIAL, PUNITIVE, INCIDENTAL OR SPECIAL DAMAGES. THESE INCLUDE LOSS OF RECORDED DATA,
INTERRUPTION OF USE, THE COST OF RECOVERY OF LOST DATA, LOST PROFITS AND THE COST OF THE
INSTALLATION OR REMOVAL OF ANY PRODUCTS, THE INSTALLATION OF REPLACEMENT PRODUCTS, AND ANY
INSPECTION, TESTING, OR REDESIGN CAUSED BY ANY DEFECT OR BY THE REPAIR OR REPLACEMENT OF PRODUCTS
ARISING FROM A DEFECT IN ANY PRODUCT.

Warranty Policy

8

Installation and Operation Manual 1.0

Contact Information

Head Office

29/A, 2nd Phase, Peenya Industrial Area, Bangalore - 560 058, India.
Tel No : [phone] / 28379401, Fax No : [phone]
For sales enquiries contact : [e-mail]

Regional Sales Offices

wAhmedabad wBangalore wChandigarh wChennai wCochin wHyderabad
w Indore w Jaipur w Kolkata w Lucknow w Mumbai w New Delhi

Service Locations

• Agra

• Ahmedabad

• Aurangabad

• Agartala

• Bangalore

• Baroda

• Bhopal

• Bhubaneshwar

• Chandigarh

• Chennai

• Cochin

• Coimbatore

•

Calicut

• Dehradun

• Guwahati

• Gwalior

• Hubli

• Hyderabad

• Indore

• Jabalpur

• Jaipur

• Jammu

• Kanpur

• Kolkata

• Kottayam

• Ludhiana

• Lucknow

•

•

Madurai

Meerut

• Mumbai

• Munnar

• Mangalore

• Mysore

• Nagpur

• New Delhi

• Ongole

• Palakkad

• Patna

• Pondicherry

• Pune

• Raipur

• Ranchi

• Rajamundry

• Salem

• Srinagar

• Tirupati

• Trichy

• Tirunelveli

• Trivandrum

• Udaipur

• Vizag

• Vijayawada

• Varanasi

Works

A-95(BIS), PIPDIC Industrial Area, Mettupalayam, Pondicherry - 605 009,
India. Tel No : [phone], Fax No : [phone]

For Service, Call our Helpline Tel No: 91-80-28397120 / 28397121

www.eandcpower.com

Page 8

vOn-line UPS

v

Inverters

vServo Controlled Voltage

Stabilizer

vEnergy Saver

vIsolation Transformers

vBatteries

vBattery Chargers

vIntelligent Power Module

vRemote Monitoring Solutions

Our other products