EBS MU LTIDR IVE - ST UDIO E DITIO N
USERS MANUAL
www.ebssweden.comwww.ebssweden.com
USERS MANUAL
EBS MU LTIDR IVE - ST UDIO E DITIO N
THANK YOU FOR PURCHASING
THE EBS MULTIDRIVE - STUDIO EDITION PEDAL!
The EBS MultiDrive is an ultra compact and robust box, capable of
producing sustain, overdrive and many other useful hot, ”tubeamp”,
distorted sounds. The overdrive engine that makes this all possible
is a simulation circuit in pure class A with a wide gain range, which
emulates a classic vintage style preamp tube. The EBS MultiDrive’s
high qualit y makes this pedal a perfect choice for the recording
environment, as well as live playing.
We hope you’ll enjoy using your EBS MultiDrive pedal.
/The EB S Team
Visit EBSSWEDEN.COM
for info on all EBS effects,
amps and accessories.
www.ebssweden.com
EBS MU LTIDR IVE - ST UDIO E DITIO N
THE CONTROLS
ACTIVE/
PASSIVE
Switch
(next to
output
jack)
Set to ACTIVE position if you are playing an
active instrument or if you have the pedal
connec ted to an effects loop. If not, set this
switch to PASSIVE.
IT IS VER Y IMPOR TANT TH AT THIS SWI TCH IS SET
CORRECTLY FOR PROPERLY FUNCTION.
DRIV E controls the amount of gain/distortion
for the ”overdr ive engine”. The range is from
0 dB (clean sound) up to 60 dB in maximum
position (very distor ted sound).
VOLUME Controls the output volume when the
pedal is active. You can also use this control
to boost your sound.
TUBESIM activates the second tube simulator,
which adds extra harmonics with added
compression and slightly less high end attack.
STANDARD (STD) - This mode select s the standard
operation for the pedal. It bypasses the low
end for excellent bass response.
FLAT - This position selects linear gain
across the entire audio spectrum. Useful for
distor ting bass sound and should be used
with fairly low Drive setting for bes t result.
This mode also produces some fuzz-like
sounds when used with high Drive.
FOOT SWITCH Switches the pedal on or off.
www.ebssweden.comwww.ebssweden.com
USERS MANUAL
USERS MANUAL
POWER OPTIONS
EBS MU LTIDR IVE - ST UDIO E DITIO N
DC POWER ADAPTOR For environmental reasons,
we recommend the use of a DC Power
Supply, such as the EBS A D-9+. The EBS
MultiDrive Studio Edition handles 9-12
V DC, and require a 2.1 mm pin center
negative type of connector.
BATTERY This pedal can run on b attery (not
included). To place a batter y in the pedal
follow these steps.
1) Remove the four screws holding
the bottom plate.
2) Carefully remove the bottom plate.
3) Place a 9V alkaline t ype; 6LR61 in
the battery holder.
4) Gently place back the bottom plate.
Attach the four mounting screws using
moderate tension.
www.ebssweden.com
EBS MU LTIDR IVE - ST UDIO E DITIO N
USERS MANUAL
HOW TO SET THE SOUND - USEFUL HINTS
In order to obtain best possible operation from the EB S MultiDrive,
check the hints below on how to improve and find your own personal
sound.
1) If you have an ac tive instrument, try switching to the passive
mode. This will increase the gain in the distortion circuit to its’
maximum. This allows for tighter high compressed sounds and is
a way to use the MultiDrive as a pure distortion pedal.
2) As in point 1 above, switch to active mode even if you are using
a passive instrument. This will not give you as much gain, but
sometimes when using the pedal to spice up your sound instead
of distorting, you may find the gain range more detailed. You
need to use fairly low settings on the volume knob to keep a
good balance between the bypassed level and the active level.
3) Try using the MultiDrive pedal as one of the fir st pedals in your
effects chain. This is because the gain stage will amplify every
small noise from other pedals being used before the MultiDrive.
4) The MultiDrive is excellent for use in an effects loop. In this setup
you can use the pedal as a post-filter enhancement stage. It
could be a good choice to make your solid state amplifier sound
like a full tube amp.
www.ebssweden.comwww.ebssweden.com
USERS MANUAL
EBS MU LTIDR IVE - ST UDIO E DITIO N
SAMPLE SOUND SETTINGS
The following examples below show a few of the many sonic
possibilities of the EBS MultiDrive.
STANDARD OVERDRIVE
This is an example of a standard overdrive
setting with a good clean edgy sound
together with untouched low end for better
definition. Use high setting for Drive and
compensate the level with the Volume.
TIGHT DISTOR TION
This is the fullrange distor tion mode, useful for
affecting the overall sound. This mode gives
less low end with harder compression and
gives the possibility to create fuz z-like sound
when tweaking the Drive. Use a moderate
setting for Drive for nor mal operation.
SMOO TH TUBE SOUND
The tubesim mode activates the second tube
simulator giving higher compression, less
attack and tube-like sounds. This position
is useful for edging up your sound while
obtaining the warmth and body of the
classical vintage tubes.
www.ebssweden.com
EBS MU LTIDR IVE - ST UDIO E DITIO N
TROUBLE SHOOTING GUIDE
Please consult the following checkpoints, before consulting one of
the authorized EBS service centers.
Checkpoint
1) Does the cable(s) work
properly?
2) Are the 1/4” plugs properly
connec ted all the way in?
3) Are the Instrument cable
attached to the Right
(input) jack, and the Amp
cable connected to the Left
(output) jack?
4) Does the pedal have a
battery, and is the bat tery
OK?
5) Does the indicator LED
light when pressing the foot
switch alternatively?
6) Does the instrument work?
7) Does the amplifier work
and is the volume turned
up?
8) If you are using a DC
adapter, Are you using an
EBS A D-9?
Action if ans wered NO
- Replace cable(s).
- Push the 1/4” plugs all
- Reconnect input and
- Put a new batter y in
- Replace/put in battery, or
- Check the instrument.
- Turn up volume or check
- Check the voltage and
USERS MANUAL
the way in.
output jacks.
the pedal.
use a DC power supply.
the amp at your nearest
EBS service center.
polarity of the adapter
you are using.
www.ebssweden.comwww.ebssweden.com
USERS MANUAL
EBS MU LTIDR IVE - ST UDIO E DITIO N
TECHNICAL SPECIFICATIONS EBS MULTIDRIVE Studio Edition
Nominal Input Level - 8 dBv (active) or
- 20 dBv (passive)
Input Impedance 700 kohms
Dry B andwidth +0/-3 dB 20 - 20k Hz
Effect Bandwidth +0/-3 dB 35 - 12k Hz
Drive Gain Range 0 - 60 dB min
Modes Standard, Flat or Tubesim
Dimensions Width 70 mm (2.8”)
Height 115 mm (4.5”)
Depth 35 mm (1.4”)
Weight 400g (0.88 lb.)
Power Requirements 9 - 12 V DC Regulated, 30 mA max.
Protected against accidental over voltage up to 18 V.
Specifications are subject to change without notice.
If you did not find the answer in this manual, please contact
EBS at support@ebssweden.com
www.ebssweden.com
Loading...