EBS FuzzMo User Manual
SAMPLE SOUND SETTINGS
The following examples below show a few of the many sonic
possibilities of the EBS FuzzMo.
USERS MANUAL
ROCK DRIVE PICK
CHARACTER
CLASSIC DRIVE PICK
CHARACTER
FUZZY DRIVE FINGERS
CHARACTER
INDUSTRIAL DRIVE
CHARACTER
MEAN DRIVE FINGERS
CHARACTER
GAIN
GAIN
GAIN
GAIN
GAIN
SHAPE
SHAPE
SHAPE
SHAPE
SHAPE
VOLUME
VOLUME
VOLUME
VOLUME
VOLUME
BLEND
BLEND
BLEND
BLEND
BLEND
EBS FUZZMO
SCOOP
EBS P
input and output.
Switches the pedal on or off. This switch is a true bypass type, switching both
F
OOT SWITCH
replace the batteryor check your powersupply.
Indicates when the pedal is active. When this LED stops glowing you should
INDICATOR LED
with the distortedsound.
the clean tone blended
- This isthe level control for
BLEND
and Character controls.
controlled by Gain, Shape
cut is enabled.
SCOOP
- Maximum mid scoop or
changes.
position gives subtle mid scoop
-
- Second or middle switch
frequency response.
FLAT
- Sets the filter to flat
three steps:
the operation of the mid scoop in
- The CHARCATER switch controls
FLAT
CHARACTER
for the high gain distortion
- This is the volume control
VOLUME
passive tone stack.
square wave through the
engine, from triangle to
actual shape of the gain
- The Shape filter sets the
SHAPE
high gain.
engine, from high to ultra
gain for the distortion
- The Gain control sets the
GAIN
ROFESSIONALBASSEQUIPMENT
EBS FuzzMo pedal.
We hope you'll enjoy using the
controls of the sounds.
scooped out in the midrange for extensive
passive high pass/low pass filter can be
variety on sounds and timbres. In addition the
blending in the original sound for a wide
ultra high gain distortion pedal with choices of
EBS FuzzMo is a high performance, fuzz mode
FuzzMo pedal!
Thank you for purchasing the EBS
THE CONTROLS
HOW TO CHANGE BATTERY
1) Carefully remove the four screws holding the bottom plate.
2) Remove the bottom plate gently.
3) Replace the old battery with a new one of the same type, 9V alkaline
type; 6LR61.
4) Gently place back the bottom plate, and make sure no cables are
squeezed. Attach the four mounting screws using moderate tension.
HOW TO USE THE EBS PHANTOM POWER™
The EBS Phantom Power System™ makes it
possible to power the EBS FuzzMo with 9V DC
directly from the EBS Drome, Gorm, HD, TD
and 1V2/Classic amps. Here is a step-by-step
instruction on howto do this.
1) Connect a stereo ¼” instrument cable (TRS, tip-ring-sleeve) between
the EBS FuzzMo pedal and the EBS amp.
2) Activate the phantom power on the amp. This is made with a flick of
a switch on most EBS amps. Please consult the manual for the EBS
amp you are using.
3) Connection done. You should now have power in the pedal, even if
the input jack is left open.
EBS PHANTOM POWER™TROUBLE SHOOTING
Checkpoint
1) Is a ¼” STEREO cable used between
the pedal and the amp?
2) Is there power available on the
RING connection of the ¼” plug?
Action if answered NO
- Replace cable to a ¼” STEREO cable.
- Make sure the phantom power is
activated on the amp.
- Check cable.
GND
PH.
POWER
SIGNAL
TROUBLE SHOOTING GUIDE
Please consult the following checkpoints, before consulting one of the
authorized EBS service centers.
Checkpoint
1) Does the cable(s) work
properly?
2) Are the ¼” plugs properly
connected all the way in?
3) Are the Instrument cable
attached to the Right (input)
jack, and the Amp cable
connected to the Left (output)
jack?
4) Does the pedal have a battery,
and is the battery OK?
5) Does the indicator LED light
when pressing the foot switch
alternatively?
6) Does the instrument work?
7) Does the amplifier work and is
the volume turned up?
8) If you are using a DC adapter,
Are you using an EBS AD-9?
Action if answered NO
- Replace cable(s).
- Push the ¼” plugs all the way in.
- Reconnect input and output jacks.
- Put a new battery in the pedal.
- Replace battery.
- Check the instrument at your
nearest service center.
- Turn up volume or check the amp
at your nearest service center.
- Check the voltage and polarity of
the adapter you are using.*
Note that only the pedal that is directly connected to the EBS amp can be powered
with phantom power. This means that if you have more than one pedal, ONLY THE
LAST one can use the EBS Phantom Power™.
MY NOTES:
*EBS Sweden AB guarantees no error free operation when using other
DC adapter than the EBS AD-9. Warranty is void if higher voltage than
specified has been used to feed the EBS FuzzMo pedal.
TECHNICAL SPECIFICATIONS EBS FUZZMO
Nominal Input Level -8 dBv
Input Impedance 900 kohms
Output Impedance <100 ohms
Gain Range 25 - 65 dB
Shape Filter Passive HP / LP
Character filter Mid Scoop 0 / -6 dB @300 Hz
Blend Bandwidth +0/-3 dB 20 - 20k Hz
Power Requirements* 9-12 V DC Regulated,
Dimensions Width 3.5” (90 mm)
Height 4.5" (115 mm)
Depth 1.4" (35 mm)
Weight 480g (1.07 lb.)
Specifications are subject to change without notice.
*EBS recommends the use of the EBS AD-9+ ,
which supplies a well stabilized power to the EBS FuzzMo and
all your other pedals that operate with a 9V battery. The high
current capacity, >1000mA, makes it possible to supply all
pedals with onlyone adapter,EBS AD-9+!
7mA@9V
DC adapter
EBS Sweden AB · Grindstuvägen 44-46 · SE-16733 Bromma · Sweden
Phone: +46-8-7350010 · Fax: +46-8-7350005
Web: www.ebssweden.com
E-mail: info@ebssweden.com
Loading...