Ebode PowerMid Classic, PowerMid Classic ST10, PowerMid Classic RE10 User Manual

PowerMid Classic
14-7-2010 2 033000=13069E
Contents of the kit
ST10 Transmitter RE10 Receiver + 9VDC SPMS PSU + 9VDC SPMS PSU
Optional accessories:
EXLED3 IR Extension
TAKE6 Universal Remote Control
14-7-2010 3 033000=13069E
User Guide
CONTENTS
1. CONFORMATY OF USE
2. INTRODUCTION
3. SET CONTENTS
4. TRANSMISSION OF YOUR ORIGINAL REMOTE CONTROL SIGNALS
5. INSTALLING THE SYSTEM
6. EXPANDING THE SYSTEM
7. TROUBLESHOOTING
1. Conformity of Use
For carefree and safe use of this product, please read this manual and safety information carefully and follow the instructions. The unit is registered as a device that does not cause or suffer from radio-frequency interference. It is CE approved and it conforms with the Low Voltage Directory. The safety and installation instructions must be observed. Technical manipulation of the product or any changes to the product are forbidden, due to security and approval issues. Please take care to set up the device correctly - consult your user guide. Young children should use the device only under adult supervision. No guarantee or liability will be accepted for any damage caused due to incorrect use of the equipment supplied, other than indicated in this owner’s manual.
SAFETY WARNINGS
To prevent short circuits, this product (except if specified for outdoor usage) should only be used inside and only in dry spaces. Do not expose the components to rain or humidity.
Only connect the adapter to the mains after checking whether the mains voltage is the same as the values on the rating labels. Never connect an adapter or power cord when it is damaged. In that case, contact your supplier. If there is any danger of a thunderstorm, it is a good precaution to unplug the power supply from the mains network in order to protect it from lightning. The same applies if the system is to be out of action for any length of time.
Avoid strong mechanical tear and wear, extreme ambient temperatures, strong vibrations and atmospheric humidity.
Do not disassemble any part of the product: the device contains live parts and no user-serviceable parts are inside. The product should only be repaired or serviced by qualified and authorized service personnel. Defected pieces must be replaced by original (spare) parts.
Batteries: keep batteries out of the reach of children. Dispose of batteries as chemical waste. Never use old and new batteries or different types of batteries together. Remove the batteries when you are not using the system for a longer period of time. When inserting batteries be sure the polarity is respected. Make sure that the batteries are not short circuited and are not disposed in fire (danger of explosion).
In case of improper usage or if you have opened, altered and repaired the product yourself, all guarantees expire. The supplier does not accept responsibility in the case of improper usage of the product or when the product is used for purposes other than specified. The supplier does not accept responsibility for additional damage other than covered by the legal product responsibility.
14-7-2010 4 033000=13069E
2. Introduction
This kit allows you to control remotely any A/V distant appliance, TV, VCR, Hi-Fi, satellite and cable box, just by using your existing remote control! The remote control signal is transmitted through walls and ceilings, up to 30 meters away.
3. Set Contents
1 Transmitter: converts IR signals of remote controls into 433.92 MHz RF messages and transmits them to the Receiver, even through walls and ceilings. 1 Receiver: converts RF messages back into IR signals to control the selected A/V source. 2 Mains power supply wall adapters 230V~50Hz to 9VDC 100mA
4. Transmission of your original remote control signals
Point your original remote control at the PowerMid Transmitter (ST10). As soon as you press a button, the transmitter captures the IR command, converts it into a RF message, and transmits it through the walls to the PowerMid Receiver (RE10). This unit converts the signal into an IR message back, in order to control the selected A/V source. For example, you can change channels on your satellite receiver while viewing it in another room. The remote control signal is transmitted through walls and ceilings, up to 30 meters away.
5. Installing the system
1. Plug the PowerMid Transmitter (ST10) power supply adapter into a 230V~ outlet in the
room where you want to use your remote control (up to 20 feet/6 meters away from where you normally sit). Plug the power supply adapter lead plug into the socket on the rear of the ST10. Make sure the front of the unit (with PowerMid name) is facing you. Fully extend the antenna.
2. Plug the PowerMid Receiver (RE10) power supply adapter into a 230V~ outlet in the
room where your TV, VCR, Stereo, etc. is located (up to 20 feet/6 meters from it). Plug the power supply adapter lead plug into the socket on the rear of the RE10. Point the front of the Receiver towards the TV, VCR, stereo etc. Fully extend the antenna.
3. Point your remote control at the Transmitter. It receives the signals and transmits them
to the Receiver. The Receiver then re-transmits these infrared signals to your TV, VCR, stereo, etc.
6. Expanding the system
-Add more Transmitters to use your remote controls in several rooms.
-Add more Receivers to control equipment in different rooms.
-Add an Infrared Extender (sold separately) if you need to place the PowerMid Receiver
next to your equipment instead of in front of it, or if your equipment is located inside a closed cabinet.
7. Troubles shooting
Note: The Transmitter and Receiver will most likely be in different rooms (up to 30 meters away). Range depends on:
1. The number of floors and walls the signal has to travel through and material these walls
and floors are made of.
2. Other 433MHz sources (e.g. wireless head phones, wireless speakers) can effect the
range. The best range will be achieved when these sources are switched off while using the PowerMid. Cordless phones will not affect the PowerMid.
3. Some satellite receivers require more careful positioning of the PowerMid system. If any
difficulty is encountered, try to move the PowerMid (Receiver) a little to various positions until it operates correctly.
14-7-2010 5 033000=13069E
DECLARATION OF CONFORMITY
Hereby, ebode declares that this PM10C is in compliance with the essential requirements and other relevant provisions of the following Directives:
1) Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on
radio equipment and telecommunications terminal equipment and the mutual recogni­tion of their conformity
2) Directive 2004/108/EC of the European Parliament and of the Council of 15 December
2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility
3) Directive 2006/95/EC of the European Parliament and of the Council of 12 December
2006 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits
4) Directive 2002/95/EC of the European Parliament and of the Council of 27 January
2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
5) Directive 2005/32/EC of the European Parliament and of the Council of 6 July 2005
establishing a framework for the setting of eco design requirements for energy-using
Technical data and copies of the original Declaration of Conformity are available and can be obtained from ebode electronics: PB 25, NL-4264ZG, the Netherlands.
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)
This document contains important information for users with regards to the proper disposal and recycling of ebode products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health.
For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
14-7-2010 6 033000=13069E
DECLARATION OF CONFORMITY TO R&TTE DIRECTIVE 1999/5/EC
for the European Community, Switzerland, Norway, Iceland and Liechtenstein
Product category: general consumer (category 3).
This equipment is in compliance with the essential requirements and other relev­ant provisions of the European R&TTE Directive 1999/5/EC
14-7-2010 7 033000=13069E
Also available from ebode: TAKE10
The TAKE10 is an elegant universal remote that is able to control up to 10 A/V devices, including TV, DVD, VCR, Cable, X10 Home Automation products and more.
You don’t even have to remember which TV station is on which button, as the brightly displayed icons on the full­colour LCD display make it easy to find and surf all the channels, plus your own favourite 'personal' buttons for you and your partner also give you quick access to all your own favourite channels too.
The remote can be set-up within 5 minutes and is very easy to use and navigate.
As the TAKE10 features RF control, you can even control equipment which is out of sight - even through doors, walls and ceilings.
Features of the TAKE10
Familiar Channel Logos
Large, Easy-to-Use Buttons and LCD Screen
His & Hers Favourite Buttons
5-Minute Setup
The Future-Proof Remote .... world's largest build-
in IR library
incl RF for controlling X10-PLC lighting control
No PC needed to program
QuickPower Feature
Multilingual
14-7-2010 8 033000=13069E
Also available from ebode: Home Automation Modules
ebode offers a wide range of Home Automation products and solutions which help you control your ‘electrical environment’. The home automation modules are ideal to
(remotely) control blinds/rollers, home cinema screen, lighting, and other household appliances.
On-Wall Modules
Product Description
EM 2-position RF wall switch, ideal for retro fit installations to
e.g. control blinds, shutter, home cinema screens but also lighting or appliances.
IMRF Single position RF wall switch, ideal for retro fit
installations to e.g. control applications or an inside or outside light.
RMV Control your shutter, blind or e.g. cinema screen via the
front panel keys, or remotely via any ebode / X10 compatible controller.
RMA Control your appliance, light or e.g. pump via the front
panel keys, or remotely via any ebode/X10 compatible controller.
RPA, RPL, RPT
Ideal for retro fit installations, the classic X10 plugin module in a new and stylish jacket. Control your appliance or lamps etc, via any ebode or X10 compatible controller via PLC AND RF!
TPC / TMML
New stylish RF remote to control any ebode or X10 compatible RF receiver.
In-Wall Modules
Product
Description
EMML 2-position RF in-wall module to install behind any
mechanical wall switch. The EMML is battery operated.
RMML In-wall RF receiver, ideal for any switches lights and
appliances up to 300W.
14-7-2010 9 033000=13069E
www.ebodeelectronics.eu
Loading...