Eberspacher Calltronic 01 User Manual

Download

Technical Description Operating Instructions Installation Instructions

Eberspächer

J. Eberspächer GmbH & Co. Eberspächerstr. 24 D - 73730 Esslingen

Telefon (zentral) (0711) 939 - 00 Telefax (0711) 939 - 0500

www.eberspaecher.com

Telephonic remote control for Eberspächer

–

auxiliary heating

Extent of delivery:

1 GSM module (stationary part) 1 set of cables for heater 1 set of cables for mini clock 1 GSM windshield antenna

incl. cleaning cloth 1 push-button 1 tab connector housing, 6-pin 1 push-on contact housing, 6-pin 6 Junior timer contacts 3 screws

A SIM card from a mobile phone network operator is required to operate the

CALLTRONIC

The mobile phone is not included in the extent of delivery!

Order number – CALLTRONIC 12 V:

22 1000 32 26 00

Additional components (Optional):

Mini clock Order No. 22 1000 31 31 00

Subject to change

Contents / Operating Instructions

Contents Page

Operating instructions

Operating the

General operating information ............................... 2

Reset PIN .............................................................. 2

Operating modes ................................................... 3

Operating the heater via the numeric keys

on the telephone ...................................................3

Functions

a) Select heating / ventilation mode .................. 4

b) Heating / ventilation running time .................. 4

c) Special functions ............................................ 5

Fault correction .....................................................5

CALLTRONIC

.................................. 2

Operating the CALLTRONIC

The

CALLTRONIC

remotely operate the heater with a DTMF telephone or mobile phone via the GSM network from a distance. You can select between the heating and ventilation operating modes. The following setting times are available for the heating period: 10, 20, 30, 40, 50, 60, 90 and 120 minutes. If preselected mode is required, a mini clock must be used instead of the push-button.

Hazard!

• Pacemakers and hearing aids can be negatively influenced.

• The SIM card and the SIM cardholder can be removed at any time – small children could swallow them.

Please note!

• When calling the are incurred due to the telephone charges.

• The range depends on the network operator (“radio hole” – transmission gaps).

• It is important that the vehicle manufacturer’s

instructions and regulations for the installation and operation of a mobile phone or GSM module are observed and complied with.

• The

CALLTRONIC

external GSM outdoor antenna in vehicles with a metalised windscreen.

is an operating element, to

CALLTRONIC

can only be operated with an

, additional costs

Page

Installation instructions

Installing the

Attaching the windscreen antenna .......................6

Insert SIM card ......................................................7

Installing the operating elements ..........................7

Insert fuse and check function ............................. 7

Technical data ....................................................... 7

Circuit diagrams parts list ..................................... 8

Circuit diagrams at the end of these instructions

General operating information

• The voice output has to be waited for before entering the numeric key, otherwise the function of the key will be ignored.

• The connection is terminated after 30 seconds without input.

• Reset PIN:

If you have forgotten your PIN number for setting up the connection to the reset it as follows:

11. Sit in the vehicle.

12. Switch off the heater if it is switched on.

13. Phone the

14. Use the push-button or the mini clock to switch

the heater on following the voice output “Enter PIN“ within 30 seconds. At the end of the 30 seconds, the heater must be switched on, otherwise the programme is aborted and the process has to be repeated.

15. Wait until the voice output “PIN invalid“.

16. Voice output “Enter PIN“.

17. Enter the PIN number “0000“.

18. Voice output “Enter PIN“.

19. Enter the PIN number “0000“ again.

10. Voice output “PIN OK“.

11. Voice output “Input function“. The PIN number “0000“ is now stored for starting the device. You can change the PIN number at any time, as described in the table on Page 5.

CALLTRONIC .................................

CALLTRONIC

using the telephone.

, you can

The following 3 operating modes are available

Note:

If malfunctions occur in the heater during operation (e.g. due to a lack of fuel), these can be interrogated after the malfunction has occurred using Function 6 (where the diagnosis cable is connected). The malfunction is corrected with the aid of the operating instructions for the heater.

1. Stand-alone operation

The function keys 0 to 7 are active at the telephone (see the following table). The push-button installed can be used to switch the heater on or off. If the heater is switched on using the push-button, the heating function is activated with a duration of 40 mins. The push-button also functions without a SIM card. The push-button flashes if an error occurs in the heater.

Operating the heater via the numeric keys on the telephone

You first have to set up a connection between the telephone and the

To do this, dial the number assigned to you by

your network operator.

The

CALLTRONIC

“Eberspächer heater – Input PIN“.

Now enter the 4-digit PIN No. (The PIN is set to 0000 in the works).

CALLTRONIC

signals the following text:

2. Combination with mini clock

The function keys 0 to 3 and 5 to 7 are active (see following table). The functions of the function key 4 (Select operating mode) are taken over by the mini clock (see installation and operating instructions for the mini clock). When switching on the heater via the mini clock, the operating mode last set with the mobile phone is always activated. If a malfunction occurs in the heater, the reading in the mini clock display changes between the time and “--“. If the

CALLTRONIC

phone, “--“ appears in the mini-clock display.

3. Combination with mini controller

When combined with the controller only serves to specify the set value. Select heating mode at the mini controller. The red LED in the mini controller only serves as an operating display – not as an operating mode display – the operating mode is selected via the remote control.

If the PIN No. is wrong, the following message appears:

“PIN invalid“.

You now have the opportunity to enter the correct PIN No.

If the PIN No. is correct, the following message appears:

“PIN OK – Input command“.

You can now enter your settings for the heater via the

CALLTRONIC

The following table on Pages 4 and 5 shows which functions are available to you.

is connected with the mobile

CALLTRONIC

, the mini

Functions

a) Select heating / ventilation operating mode

Numeric key Function Voice output

0 Switch off operating mode Heater off – Input command

1 Activate heating mode • Heater on – duration... minutes – Input command

2 Activate ventilation mode • Ventilation on – duration ... minutes – Input command

3 Status check • Heater on – duration ... minutes – Input command

b) Heating / ventilation running time

(If the mini clock is connected, the following function for numeric key 4 does not work)

Numeric key Function Voice output

4 Input duration • Input duration

1 Select duration 10 mins. Duration 10 minutes – Input command

2 Select duration 20 mins. Duration 20 minutes – Input command

3 Select duration 30 mins. Duration 30 minutes – Input command

4 Select duration 40 mins. Duration 40 minutes – Input command

(heating / ventilation)

• Heater on (only for mini clock) – Input command

• Ventilation on (only for mini clock) – Input command

• Heater on (only for mini clock) – Input command

• Ventilation on – duration ... minutes – Input command

• Ventilation on (only for mini clock) – Input command

• Heater off – Input command

Heating and Ventilation • Input invalid – Input command

(Only if mini clock connected)

5 Select duration 50 mins. Duration 50 minutes – Input command

6 Select duration 60 mins. Duration 60 minutes – Input command

7 Select duration 90 mins. Duration 90 minutes – Input command

8 Select duration 120 mins. Duration 120 minutes – Input command

9 No function Input invalid – Input command

0 No function Input invalid – Input command

c) Special functions

Numeric key Function Voice output

5 The following language is selected by pressing Key 5.

The following function, numeric key 6, only applies for the trade appliances (retrofit) – diagnosis cable (blue / white) must be connected

6 Enquire heater condition • Heater OK – Input command

7 Change PIN Input new PIN

xxxx Enter new PIN Input new PIN

xxxx Enter new PIN • PIN OK – Input command

8 No function Input invalid – Input command

9 No function Input invalid – Input command

Repeat the function until the required language is announced.

Language selected: Input command

• German (in the selected language)

• Swedish

• English

• French

(Diagnosis analysis) • Heater not OK – Input command

• Input invalid – Input command

(if diagnosis cable not connected)

(for confirmation) • Input invalid – Input command

Fault correction

If problems occur while you are using the

CALLTRONIC

following list.

, first try to find a solution in the

If the problem continues, please contact an Eberspächer service workshop.

Problem Possible cause Possible corrective measure

No connection No supply voltage Check fuse and wiring to the CALLTRONIC Weak signal Change location of the vehicle; check antenna

Outside of the GSM supply area Check the supply range of the network operator

Network block set Check network blocks

Network overloaded Call again later

SIM card invalid Call using another phone network operator

SIM card incorrectly inserted Ensure that the SIM card has been correctly

inserted; the card holder must lock home

SIM card contacts soiled Clean the SIM card with a dry cloth

SIM card with wrong number Only SIM cards with 3 volts possible of volts

SIM card damaged Carry out a visual check;

give SIM card back to network operator

Installation Instructions

Installing the CALLTRONIC

CALLTRONIC

The vehicle in accordance with the installation drawing. Wherever possible, the installation position should not be subjected to direct sunlight.

is only installed in the inside of the

Please note!

• The SIM card should be able to be replaced even when installed.

• Please ensure that you observe and comply with the instructions and regulations of the vehicle manufacturer with respect to the installation and operation of a mobile phone or GSM module.

햲

CALLTRONIC

햳 SIM cardholder 햴 Push-button with LED

Attaching the windscreen antenna

햵 Heater cable 햶 Mini clock cable (optional) 햷 GSM windscreen antenna

The windscreen antenna is attached to the inside of the windscreen or rear window.

Assembly:

Before sticking on the windscreen antenna 햴, the relevant position on the screen 햳 should be cleaned using the enclosed cloth and should be dry. Pull off the protective strip from the sticky tabs. Install the antenna cable to the connect.

Note:

Length of the antenna cable: 5 m.

CALLTRONIC

햲 and

Insert the SIM card

You must insert the SIM card before you can use the

CALLTRONIC

햲 To release the lock on the SIM cardholder, press

the yellow button – the SIM cardholder springs out a bit.

햳 Pull out the SIM cardholder. 햴 Insert SIM card with chip (contacts) facing

upwards.

햵 Re-insert the SIM cardholder in the appliance,

until it locks into place.

Note:

Only SIM cards without a PIN and with 3-volt technology can be used.

Installation of the operating elements

Push-button

Fit the enclosed push-button in the view of the driver (Drill hole 10 mm, max. wall thickness 2.5 mm). Connect the cables in accordance with the circuit diagram.

Mini-clock (Option)

Install the mini clock (separate add-on) in accordance with the instructions supplied. Connect the cables in accordance with the circuit diagram.

Technical data

Working Voltage: 12 Volts

GSM Bands: Dual Band EGSM900

GSM1800

GSM Class: Small MS

Transmit Power: Class 4 in EGSM900

Class 1 in GSM1800

Operating Temperature: –20 °C to +50 °C

Storage Temperature: –30 °C to +85 °C

Dimensions: 140 x 100 x 36 mm

Insert the fuse and check the function

The operating element must be connected and fully functioning before inserting the fuse. Insert the function of the onds (time until the GSM module has signed on to the network) with a telephone or mobile phone.

Please note!

The heater diagnosis cable (blue / white) must be connected for fault recognition (only for trade appliances – retrofit). The operating element must be connected and fully functioning before inserting the fuse. The appliance detects whether a push-button or a mini-clock is connected when the voltage supply is applied for the first time. The subsequent changes.

CALLTRONIC

(5 A) fuse and check the

after approx. 30 sec-

does not accept