Eberspacher Calltronic 01 User Manual
Technical Description
Operating Instructions
Installation Instructions
Eberspächer
J. Eberspächer
GmbH & Co.
Eberspächerstr. 24
D - 73730 Esslingen
Telefon (zentral)
(0711) 939 - 00
Telefax
(0711) 939 - 0500
www.eberspaecher.com
®
Telephonic remote control for Eberspächer
–
auxiliary heating
Extent of delivery:
1 GSM module (stationary part)
1 set of cables for heater
1 set of cables for mini clock
1 GSM windshield antenna
incl. cleaning cloth
1 push-button
1 tab connector housing, 6-pin
1 push-on contact housing, 6-pin
6 Junior timer contacts
3 screws
A SIM card from a mobile phone network operator
is required to operate the
CALLTRONIC
.
The mobile phone is not included in the extent
of delivery!
Order number – CALLTRONIC 12 V:
22 1000 32 26 00
Additional components (Optional):
Mini clock
Order No. 22 1000 31 31 00
D
S
Subject to change
GB
F
1
Contents / Operating Instructions
Contents Page
Operating instructions
Operating the
General operating information ............................... 2
Reset PIN .............................................................. 2
Operating modes ................................................... 3
Operating the heater via the numeric keys
on the telephone ...................................................3
Functions
a) Select heating / ventilation mode .................. 4
b) Heating / ventilation running time .................. 4
c) Special functions ............................................ 5
Fault correction .....................................................5
CALLTRONIC
.................................. 2
Operating the CALLTRONIC
The
CALLTRONIC
remotely operate the heater with a DTMF telephone
or mobile phone via the GSM network from a distance. You can select between the heating and
ventilation operating modes. The following setting
times are available for the heating period: 10, 20,
30, 40, 50, 60, 90 and 120 minutes.
If preselected mode is required, a mini clock must
be used instead of the push-button.
Hazard!
• Pacemakers and hearing aids can be negatively
influenced.
• The SIM card and the SIM cardholder can be
removed at any time – small children could
swallow them.
Please note!
• When calling the
are incurred due to the telephone charges.
D
• The range depends on the network operator
(“radio hole” – transmission gaps).
• It is important that the vehicle manufacturer’s
S
instructions and regulations for the installation
and operation of a mobile phone or GSM module
are observed and complied with.
• The
GB
CALLTRONIC
external GSM outdoor antenna in vehicles with
a metalised windscreen.
is an operating element, to
CALLTRONIC
can only be operated with an
, additional costs
F
Page
Installation instructions
Installing the
Attaching the windscreen antenna .......................6
Insert SIM card ......................................................7
Installing the operating elements ..........................7
Insert fuse and check function ............................. 7
Technical data ....................................................... 7
Circuit diagrams parts list ..................................... 8
Circuit diagrams at the end of these instructions
General operating information
• The voice output has to be waited for before entering the numeric key, otherwise the function of the
key will be ignored.
• The connection is terminated after 30 seconds
without input.
• Reset PIN:
If you have forgotten your PIN number for setting
up the connection to the
reset it as follows:
11. Sit in the vehicle.
12. Switch off the heater if it is switched on.
13. Phone the
14. Use the push-button or the mini clock to switch
the heater on following the voice output “Enter
PIN“ within 30 seconds. At the end of the 30
seconds, the heater must be switched on,
otherwise the programme is aborted and the
process has to be repeated.
15. Wait until the voice output “PIN invalid“.
16. Voice output “Enter PIN“.
17. Enter the PIN number “0000“.
18. Voice output “Enter PIN“.
19. Enter the PIN number “0000“ again.
10. Voice output “PIN OK“.
11. Voice output “Input function“.
The PIN number “0000“ is now stored for starting
the device.
You can change the PIN number at any time, as
described in the table on Page 5.
CALLTRONIC .................................
CALLTRONIC
CALLTRONIC
using the telephone.
, you can
6
2
The following 3 operating modes
are available
Note:
If malfunctions occur in the heater during operation
(e.g. due to a lack of fuel), these can be interrogated after the malfunction has occurred using
Function 6 (where the diagnosis cable is connected).
The malfunction is corrected with the aid of the
operating instructions for the heater.
1. Stand-alone operation
The function keys 0 to 7 are active at the telephone
(see the following table).
The push-button installed can be used to switch the
heater on or off. If the heater is switched on using
the push-button, the heating function is activated
with a duration of 40 mins. The push-button also
functions without a SIM card. The push-button
flashes if an error occurs in the heater.
Operating the heater via the numeric
keys on the telephone
You first have to set up a connection between the
telephone and the
To do this, dial the number assigned to you by
your network operator.
The
CALLTRONIC
“Eberspächer heater – Input PIN“.
Now enter the 4-digit PIN No.
(The PIN is set to 0000 in the works).
CALLTRONIC
signals the following text:
.
2. Combination with mini clock
The function keys 0 to 3 and 5 to 7 are active (see
following table).
The functions of the function key 4 (Select operating
mode) are taken over by the mini clock (see installation and operating instructions for the mini clock).
When switching on the heater via the mini clock, the
operating mode last set with the mobile phone is
always activated. If a malfunction occurs in the
heater, the reading in the mini clock display changes
between the time and “--“.
If the
CALLTRONIC
phone, “--“ appears in the mini-clock display.
3. Combination with mini controller
When combined with the
controller only serves to specify the set value.
Select heating mode at the mini controller. The red
LED in the mini controller only serves as an operating display – not as an operating mode display – the
operating mode is selected via the remote control.
If the PIN No. is wrong, the following message
appears:
“PIN invalid“.
You now have the opportunity to enter the correct
PIN No.
If the PIN No. is correct, the following message
appears:
“PIN OK – Input command“.
You can now enter your settings for the heater via
the
CALLTRONIC
The following table on Pages 4 and 5 shows which
functions are available to you.
is connected with the mobile
CALLTRONIC
.
, the mini
D
S
GB
F
3
Functions
a) Select heating / ventilation operating mode
Numeric key Function Voice output
0 Switch off operating mode Heater off – Input command
1 Activate heating mode • Heater on – duration... minutes – Input command
2 Activate ventilation mode • Ventilation on – duration ... minutes – Input command
3 Status check • Heater on – duration ... minutes – Input command
b) Heating / ventilation running time
(If the mini clock is connected, the following function for numeric key 4 does not work)
Numeric key Function Voice output
4 Input duration • Input duration
1 Select duration 10 mins. Duration 10 minutes – Input command
2 Select duration 20 mins. Duration 20 minutes – Input command
3 Select duration 30 mins. Duration 30 minutes – Input command
4 Select duration 40 mins. Duration 40 minutes – Input command
(heating / ventilation)
• Heater on (only for mini clock) – Input command
• Ventilation on (only for mini clock) – Input command
• Heater on (only for mini clock) – Input command
• Ventilation on – duration ... minutes – Input command
• Ventilation on (only for mini clock) – Input command
• Heater off – Input command
Heating and Ventilation • Input invalid – Input command
(Only if mini clock connected)
D
S
GB
F
5 Select duration 50 mins. Duration 50 minutes – Input command
6 Select duration 60 mins. Duration 60 minutes – Input command
7 Select duration 90 mins. Duration 90 minutes – Input command
8 Select duration 120 mins. Duration 120 minutes – Input command
9 No function Input invalid – Input command
0 No function Input invalid – Input command
4
c) Special functions
Numeric key Function Voice output
5 The following language is selected by pressing Key 5.
The following function, numeric key 6, only applies for the trade appliances (retrofit) –
diagnosis cable (blue / white) must be connected
6 Enquire heater condition • Heater OK – Input command
7 Change PIN Input new PIN
xxxx Enter new PIN Input new PIN
xxxx Enter new PIN • PIN OK – Input command
8 No function Input invalid – Input command
9 No function Input invalid – Input command
Repeat the function until the required language is announced.
Language selected: Input command
• German (in the selected language)
• Swedish
• English
• French
(Diagnosis analysis) • Heater not OK – Input command
• Input invalid – Input command
(if diagnosis cable not connected)
(for confirmation) • Input invalid – Input command
Fault correction
If problems occur while you are using the
CALLTRONIC
following list.
, first try to find a solution in the
If the problem continues, please contact an
Eberspächer service workshop.
Problem Possible cause Possible corrective measure
No connection No supply voltage Check fuse and wiring
to the CALLTRONIC Weak signal Change location of the vehicle; check antenna
Outside of the GSM supply area Check the supply range of the network operator
Network block set Check network blocks
Network overloaded Call again later
SIM card invalid Call using another phone network operator
SIM card incorrectly inserted Ensure that the SIM card has been correctly
inserted; the card holder must lock home
SIM card contacts soiled Clean the SIM card with a dry cloth
SIM card with wrong number Only SIM cards with 3 volts possible
of volts
SIM card damaged Carry out a visual check;
give SIM card back to network operator
5
D
S
GB
F
Installation Instructions
Installing the CALLTRONIC
CALLTRONIC
The
vehicle in accordance with the installation drawing.
Wherever possible, the installation position should
not be subjected to direct sunlight.
is only installed in the inside of the
Please note!
• The SIM card should be able to be replaced even
when installed.
• Please ensure that you observe and comply with
the instructions and regulations of the vehicle
manufacturer with respect to the installation and
operation of a mobile phone or GSM module.
햲
CALLTRONIC
햳 SIM cardholder
햴 Push-button with LED
Attaching the windscreen antenna
D
S
GB
F
햵 Heater cable
햶 Mini clock cable (optional)
햷 GSM windscreen antenna
The windscreen antenna is attached to the inside
of the windscreen or rear window.
Assembly:
Before sticking on the windscreen antenna 햴, the
relevant position on the screen 햳 should be cleaned
using the enclosed cloth and should be dry.
Pull off the protective strip from the sticky tabs.
Install the antenna cable to the
connect.
Note:
Length of the antenna cable: 5 m.
6
CALLTRONIC
햲 and
Loading...