CALLTRONIC
Operating instructions.
Telephone remote control
for Eberspächer parking heaters.
22 1000 33 61 01
10.2008
Contents
Introduction
Dear Customer• .................................................................................................... 3
Application• .......................................................................................................... 3
Operation and Adjustment
Operation with fixed line / mobile phone• .............................................................. 4
Operating functions with fixed line / mobile phone• ............................................... 4
Programming the Calltronic• ................................................................................. 5
Operating with pushbuttons• ................................................................................ 5
Heater operating status• ....................................................................................... 6
Note• .................................................................................................................... 6
Explanation• ......................................................................................................... 6
Key to symbols used• ........................................................................................... 6
2
Introduction
Dear Customer,
Thank you for purchasing the Calltronic
telephone remote control.
With this product you have a convenient
and innovative way of operating your
Eberspächer parking heater.
These operating instructions supplement the explanations of your JE service
partner who installs the equipment and
summarise the functions of the Calltronic
once again.
Application
Your Eberspächer parking heater can be
remotely controlled by means of a phone
using DTMF data transmission. All mobile
and fixed line phones which enable multifrequency dialling tones to be sent are
suitable as controls.
When you call your Calltronic you are
guided through the menu and are enabled
to use the Eberspächer parking heater
located in your vehicle in an easy way.
Please note!
Before starting up the Calltronic, note •
and follow the general operating instructions of your Eberspächer parking
heater and note the location of your
vehicle.
In the case of water heaters it is neces-•
sary to switch the vehicle's heating to
“Hot” before leaving the vehicle.
The vehicle blower must be set to level
1 if a 3 stage blower is used, to level 2 if
a 4 stage blower is used and to at least
1/3 of the blower output if a stepless
blower is used.
We recommend setting the heating •
period to match the journey time to
avoid discharging of the vehicle's bat-
tery.
Example:
If the journey time is approximately 30
minutes (single trip) you should set the
heating period to 30 minutes.
The Calltronic is set to 30 min heating •
period in the factory.
A once-off heating period of 10 – 120 •
minutes can be selected.
3
Operation and Adjustment
Operation
with fixed line / mobile phone
Set your fixed line / mobile phone to •
tone dialling (DTMF). For information
regarding this, please refer to the operating instructions for your phone. This
functional is already set as a default in
most mobile phones.
You have applied for and received a •
Calltronic phone number from your network provider.
Dial your Calltronic phone number. •
After you have established the connection you will hear the greeting «EBERSPÄCHER CALLTRONIC, WELCOME»,
followed by the request «PLEASE
ENTER YOUR PASSWORD».
Operating functions in the main menu
My Calltronic phone number:
Function Press the key Note (see page 6)
Activate heating
Deactivate heating / ventilation
Activate ventilation
Heat / Ventilate
Extend switched on period
Heat / Ventilate
Query remaining switched on period
Internal preselection timer
Activate / deactivate
Query current time
Programming (see page 5)
Enter your password (2 digit code).
The password is set to «00» in the factory (
list of the availalbe functions follows in
an endless loop or the selected function is confirmed. If your input is incorrect or you do not enter a password you
will hear the message «INPUT INCORRECT» and the available functions are
repeated again twice. The the phone
connection is disconnected.
The existing menu structure automati-
cally adapts itself to the respective current device status.
). If the input is correct a
00#
1
1
2
2
3
4
1
5
0
2
4
Operation and Adjustment
Programming the Calltronic
Open the programming menu by entering 0 in the main menu
Programming menu Press the key sequence Note (see page 6)
new password
Changing the password
Heat
Changing the switched on
period
Ventilate
Changing the switched on
period
Programming the current time
Heating switching on time
Ventilation switching on time
Exit programming
1
(2 digits)
password
2 or 3 digits
2
(10 – 120 minutes)
2 or 3 digits
3
(10 – 120 minutes)
2 digits (ⱕ 23 hours) and
4
2 digits (ⱕ 59 minutes)
2 digits (ⱕ 23 hours) and
5
2 digits (ⱕ 59 minutes)
2 digits (ⱕ 23 hours) and
6
2 digits (ⱕ 59 minutes)
0
Operating with pushbuttons
The scope of supply includes a pushbutton. This must be installed and is used to
operate and display the current operating
status of your heater.
repeat new
#
#
#
#
When the button is pressed the last
control function is repeated. If the heater
is activated when the button is pressed
the current heating or ventilation cycle is
ended.
3
3, 4
3, 4
3
3
3
Heater operating status
LED in the pushbutton
continuously lit • Æ Heating active
flashes slowly • Æ Ventilation active
flashes quickly • Æ while the button is being pressed
5
Operation and Adjustment
Note Explanation
1 Switches the heat or ventilate mode on at the programmed time for
2 If no input is made within 10 seconds the Calltronic automatically
3 If the input was incorrect or no input is made within 5 seconds
4 The minute value entered is saved as the new switched on period
Key to symbols
used
01234
56789
«xxxxx» Calltronic announcement text
#
ⱕ
the selected switched on period.
IMPORTANT:
The switching on takes place for one heating or ventilation event
only. To repeat it is necessary to reactivate the preselection timer.
returns to the main menu.
the Calltronic returns to the programming menu with the message «INPUT INCORRECT». The setting to date remains saved,
unchanged.
for heat or ventilate mode. The heating or ventilation period is preset
in the factory to 30 minutes.
Phone keys (see phone instructions)
Press the key(s)
“Hash” key
Less or equal to
6
www.eberspaecher.com
J. Eberspächer
GmbH & Co. KG
Eberspächerstraße 24
D-73730 Esslingen
Phone 0711 939-00
Fax 0711 939-0643
info@eberspaecher.com
22 1000 33 61 01 EN 10.2008 Subject to change without notice Printed in Germany © J. Eberspächer GmbH & Co. KG
Loading...