Page 1
Assembly Instruction Sheet #IS-CMA1405WT
For Style CMA1405WT
Pleasegoto forproductcleaningtips.Gotothe selection.
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses, ladder,drillwith
7/32-inchdrillbit.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
Integrated35WLED
45-60minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
CAUTION: To reduce the risk of fire, electrical shock, or personal injury, do not touch or remove the spot light on the rail when the light
is on. Instead, turn off the electrical power. Unscrew the caps and to remove the spot light from the rail. Then reinstall them back onto
the desired positions of the rail.
Package Contents
Mounting Screw
B
x2
Wall Anchor
C
Crossbar
A
x1
x5
Self-tapping
D
Screw
x5
Rail
E
x1
Ceiling
Canopy
F
x1
G
Rail
Support
x5
Spot Light
H
x5
STEP 1 Attach Crossbar to
Outlet Box
A. Attach the Crossbar (A) to Outlet
STEP 2 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
B. Use standard wire connectors (not included) to make all wire
-
Outlet
Box
Box and secure by threading
Outlet Box Screws (not supplied)
into the Mounting Holes on the
Outlet Box. Tighten until snug.
Figure 1
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
A
Outlet Box
Screw
STEP 3 - Attach Ceiling Canopy
to Crossbar
A. Line up the holes on the side of
the Ceiling Canopy (F) to the
mounting holes on the
Crossbar (A). Secure them with
Mounting Screws (B). Tighten
until sung.
F
Figure 3
STEP 4 Determine Support Position-
A. Identify the first Rail Supports (G) position approximately 14-18”
from the Ceiling Canopy (F) and mark the position.
bent in gentle curves or straight line as desired.
B. By using the drill with 7/32-inch drill bit, drill holes on marks.
CEILING
F
14~18 inches
Therailmaybe
Support Base
G
A
B
2018 Quoizel Inc.
Green Ground Screw
on the Crossbar
Need assistance with parts orassembly? CallQuoizel customerservice at1-800-645-3184
Figure 2
Thank you for purchasinga Quoizelproduct.
or visit us on-lineat www.quoizel.com
1of3
Figure 4
ReleasedDate:2018-02-28
Page 2
STEP 5 Install Rail support-
A. Disassemble support base
from Rail Supports (G) as
shown.
Figure 5A
Support
Base
(Step 7 Continued)
D. Shape the Rail (E) as your desired. Then mark and drill the desired
positions on the ceiling for the rest of the Rail Supports (G).
Pipe of
G
Rail Support
F
CEILING
C
Support Base
B. Insert the Wall Anchor (C) into the
drilled hole on the ceiling. Pass the
Support Base over the Wall Anchor
(C) and then screw the self-tapping
screw (D) through the Support
Base into the wall anchor until
Cap
D
tight.
C. Thread the Rail Support (G) into
the Support Base and hand tighten
until snug.
G
Pipe of
Rail Support
Figure 5B
STEP 6 Instal Rail to Rail Support
-
A. Carefully take out the Rail (E) from the package and unfold it. There
has an Indented Groove and Brass Strip in the side of the Rail (E).
B. Turn the Moveable Part of the Rail Support (G) up.Attach the Rail
(E), while making certain the indented groove are facing toward the
bump, securely into the Rail Support (G).
NOTE: The Shallow V-pit on the Rail (E) is always facing to the
ceiling.
D. Close back the moveable part of Rail Support (G) over the rail, then
restore the Caps back to the Rail Support (G).
Brass Strip
G
Moveable part
of Rail Support
Rail
Indented
Rail
Groove
Support
Figure 6B
E
Moveable Part
of RailAdapter
Rail Adapter
Brass Strip
Bump
Rail Adapter
Brass Clip
Shallow V-Pit
Cap
Indented Groove
Brass Strip
Rail
Figure 7
Brass Clip
STEP 8 Spot Light Installation
-
A. Choose one spot light, unscrews the Caps from the Rail Adapter of
Spot Light (H), then turn the Moveable Part of RailAdapter body
down.
B. Attach the Rail Adapter of the Spot Light (H) onto the Rail (E). Close
back the Moveable Part of RailAdaptor body over the Rail (E), then
restore the Caps back to the Rail Adapter. Make certain that the
Brass Clips of theAdapter are connected properly with the Brass
Strips of the Rail.
CAUTION: To ensure the fixture works correctly, make sure the
connection between the adapter and the rail is correct. The
Shallow V-pit on the Rail is always facing to the ceiling.
C. Follow steps A~B to install the other spot lights onto the rail.
Note: Adjust the spotlight head to a desired position by using
the swivel.
Brass Strip
Cap
Figure 6A
STEP 7 Instal Rail to Ceiling Canopy
-
A. Unscrew the Caps from the Rail Adapter, and then turn the Moveable
Part of the RailAdapter body up.
B. Attach the Rail (E) onto the slot of the pre-tightened Rail Adapter.
Note: If the Adapter is not able to close around the Rail, turn Rail
around so Adapter fits properly.
C. Close back the Moveable Part of RailAdaptor body over the Rail (E),
then restore the caps back to the rail adapter. Make certain that the
Brass Clips of the adapter are connected properly with the Brass
Strips of the Rail (E).
CAUTION: To ensure the fixture works correctly, make sure the
connection between the Adapter and the Rail is correct.
Thank you for purchasinga Quoizelproduct.
Need assistance with parts orassembly? CallQuoizel customerservice at1-800-645-3184
2018 Quoizel Inc.
or visit us on-lineat www.quoizel.com
Your fixture is now assembled and ready to use. Enjoy!
Rail
Cap
E
Rail
Adapter
H
Moveable Part
of RailAdapter
Spot Light
Head
Figure 8A
2of3
Indented
Bump
Shallow V-Pit
Brass
Strip
Groove
Brass Clip
Rail Adapter
Figure 8B
ReleasedDate:2018-02-28
Rail
Page 3
CMA1405WT
FINISH: WESTERN BRONZE
108”
4.75”Dia.
1.75”
11.75”
9.25”
3.75”
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
3”
2018 Quoizel Inc.
Need assistance with parts orassembly? CallQuoizel customerservice at1-800-645-3184
Thank you for purchasinga Quoizelproduct.
or visit us on-lineat www.quoizel.com
3of3
ReleasedDate:2018-02-28
Loading...