Page 1
3-Pieces Bistro Set
A
R
N
R
T
A
W
1
1
R
Y
A
E
Y
Page 2
IMPORTANT, RETAIN FOR
FUTURE REFERENCE:
READ CAREFULLY.
Safety
For domestic use only.
Don't tighten all the bolts before the product is fully assembled.
It would be useful to ask someone to help you assemble
the product.
Periodic structural checks of this product should be
undertaken, do not use if you have any doubts about its
Do not stand on the seat.
Do not sit on the armrest.
Do not let children play with this product.
Maximum load per seat: 200 lbs.
At the beginning of the season
product are secure, do not use if you have any doubts
At the end of the season
This product should be stored under cover during
prolonged spells of adverse weather (wet or cold) and
also during the winter (ideally in a garden shed or
garage).
Always clean and dry thoroughly before storage.
- 1 -
Page 3
Tips for Cushions
In order to compress the package, we put the cushions in
the gap of some parts. So there may be crinkle on the fabric.
Don’t worry. Just flap every corner of the cushion evenly and
it will get back into its original shape soon.
1
3
2
OK
- 2 -
Page 4
COMPONENT LIST -ARMCHAIR X 2
Item
no.
D
E
F
G
I
Reference
Image
Description Qty.
Seat Base
Seat Back
Right Armrest
Left Armrest
Seat Cushion
1
1
1
1
1
R1
Z
T
M6X40
Head Cap Screws
Washer
Allen Key
- 3 -
11
11
1
Page 5
NOTE:
When tightening the screws, tighten sequentially.
DO NOT tighten any screws fully and then move on to the next one.
This may cause the frame to warp.
If there is still wobbles or screw holes cannot be aligned,loosen the
screws and execute this same process.
If the Chair is not stable it could lead to damage to the product.
1
Attach the Seat Base (D) to the Seat Back (E) by securing with M6*40 Head
Cap Screw (R1) and Washer (Z). Do this in 1 place.
D
E
R1
Z
x1
x1
NOTE:DO NOT TIGHTEN THE SCREWS COMPLETELY.
- 4 -
Page 6
Attach the Seat Base (D) to the Armrests (F) & (G) by securing with M6*40
2
Head Cap Screws (R1) and Washers (Z). Do this in 6 places.
F
G
D
E
R1
Z
x6
x6
NOTE:DO NOT TIGHTEN THE SCREWS COMPLETELY.
- 5 -
Page 7
Attach the Seat Back (E) to the Armrests (F) & (G) by securing with M6*40
3
Head Cap Screws (R1) and Washers (Z). Do this in 4 places.
E
G
D
R1
F
Z
x4
x4
NOTE:DO NOT TIGHTEN THE SCREWS COMPLETELY.
- 6 -
Page 8
Tighten all 11 Screws into place with Allen Key (T).
4
T
x11
NOTE:IF ANY SCREW HOLES CANNOT BE ALIGNED,
LOOSEN ALL THE SCREWS AND GO BACK STEP
1 AND RESTART ASSEMBLY.
- 7 -
Page 9
Place the chair on a level surface, then place Seat Cushion (I) on the
5
chair. Your chair is ready for use.
I
Adjust Pre-installed levellers
height for balance
- 8 -
Adjust height
for balance
Adjust low
for balance
Page 10
COMPONENT LIST -TABLE
Item
no.
A
B
C
H
R1
Reference
Image
Description Qty.
Table Top
Table Leg
Connector
Glass 1
M6X40
Head Cap Screws
1
2
1
4
R2
Z
T
M6X20
Head Cap Screws
Washer
Allen Key
- 9 -
4
8
1
Page 11
NOTE:
When tightening the screws, tighten sequentially.
DO NOT tighten any screws fully and then move on to the next one.
This may cause the frame to warp.
If there is still wobbles or screw holes cannot be aligned,loosen the
screws and execute this same process.
If the Table is not stable it could lead to damage to the product.
1
Attach the Table Legs (B) to the Table Top (A) by securing with M6*40 Head
Cap Screws (R1) and Washers (Z). Do this in 4 places.
1
R
Z
x4
A
B
B
x4
NOTE:DO NOT TIGHTEN THE SCREWS COMPLETELY.
- 10 -
Page 12
Attach the Connector (C) to the Table Legs (B) by securing with M6*20
2
Head Cap Screws (R2) and Washers (Z). Do this in 4 places.
B
A
B
C
RR2
ZZ
x4
x4
NOTE:DO NOT TIGHTEN THE SCREWS COMPLETELY.
- 11 -
Page 13
Tighten all 8 Screws into place with Allen Key (T).
3
T
x8
NOTE:IF ANY SCREW HOLES CANNOT BE ALIGNED,
LOOSEN ALL THE SCREWS AND GO BACK STEP
1 AND RESTART ASSEMBLY.
- 12 -
Page 14
Place the table on a level surface, then place Glass (H) on the table.
4
Your table is ready for use.
H
Adjust height
for balance
Adjust low
for balance
Adjust Pre-installed levellers
height for balance
- 13 -
Loading...