Page 1
ASSEMBLY INSTRUCTIONS
2 Drawer Writing Desk , Espresso
Page 2
Desktop maximum
weight capacity
= 40lbs
Drawer maximum
weight capacity
= 10lbs
2 OF 12
Page 3
51-7005HAES
Drawer Front Panel
Drawer Left Panel
Drawer Right Panel
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED.
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- HAVE THE TOOLS BELOW BEFORE YOU BEGIN ASSEMBLING.
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
- DO NOT SHIFT OR DRAG THE PRODUCT AFTER ASSEMBLY.
- THE FOLLOWING TOOLS ARE NOT INCLUDED.
ROUND STICKER
I
3 OF 12
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
- DO NOT USE FURNITURE WAX OR POLISH AS THE UNIT
IS FINISHED WITH A PROTECTIVE CLEAR LACQUER.
Page 4
Start assembling by xing Wood dowels (1) to Panels (A), (B), (D), (E), (F), (H), (I) & (K).
X2
X2
Fix the nine Minix Bolts (2) to the bottom of Desktop (C) & both Drawer Front Panels (G) using
predrilled holes.
Page 5
Screw two Drawer Slides (3-CL) to the Left Outside Shelf Panel (E) using Euro Screws (4).
Then screw two Drawer Slides (3-CR) to the Right Side Panel (B) using four Euro Screws (4).
THIRD
LAST HOLE
SECOND
HOLE
Page 6
Screw Left Outside Shelf Panel (E) to Bottom Shelf Panel (F)
with one Unitar Screw (5) using predrilled holes.
(Make sure nished sides are facing outwards)
Attach Back Panels (D and K) to Side Panels (A and B) with six Unitar Screws (5) using predilled holes
(making sure both Back Panels nished ends are facing inside and towards each other).
Then, using rubber hammer, hammer four plastic Nail Legs (6) into the bottom of Side Panels (A and B).
Page 7
Attach Shelf Panels (E and F) with three Unitar Screws (5) using predrilled holes
(making sure nished side is facing front of desk).
E
Press in each of the ve Cams (7), making sure the arrow on top is pointing towards the smaller hole.
Attach Desktop (C) to desk by aligning the Minix Bolts (2) into the smaller holes. Turn the Cam clockwise
to lock it into the Minix Bolt (2).
Caution:
Do not over tighten
cams.
Page 8
Attach Sides of Drawer (H and I) to Drawer Front Panel (G) by rst pressing each Cam (7)
into the larger hole, making sure the arrow is pointed towards the smaller hole. Align
Minix Bolts (2) with the smaller holes. Turn each Cam clockwise to lock it into the Minix
Bolt (2).
Slide Drawer Bottom Panel (Z) between Panels (I and H).
(Making sure nished side is facing inside the drawer).
Then attach Drawer Back Panel (J) with four Long Screws (8) into predrilled holes.
Page 9
Attach Handle (9) to Drawer Front Panel with two Screws (9),
making sure the lip of the handle is facing the bottom of the drawer.
Page 10
Attach Drawer Slides (10) to the bottom of drawer using four Short Screws (11).
10-DR attaches to Panel (I) and 10-DL attaches to Panel (H)
THIRD TO
LAST HOLE
THIRD
HOLE
Page 11
Use the eight Round Stickers (12) to cover all exposed screws on the exterior of your
new desk.
Page 12
DO NOT stand on the desk. Do not use the desk as a stepladder.
•
DO NOT use the desk unless all bolts and screws are rmly secured.
•
Every 6 months, check all bolts and screws to ensure they are tight.
•
This product is California 93120 Compliant for Formaldehyde.
•
12 OF 12
Loading...