Page 1
6 Drawer Double Dresser
Instruction Manual
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED.
Small parts may present choking hazard prior to assembly.
Keep out of reach of children until assembly is complete.
Made in Vietnam
Page 2
WARNING
Serious or fatal crushing injury can occur from furniture tip-over. To help prevent tip-over:
- Install tip-over retrain provided.
- Place heaviest items on the lowest drawers.
- Unless specifically designed to accommodate, set Tv’s or other heavy objects on the top of
this product.
- allow children to climb or hang on drawers, doors or shelves.
Never
- open more than one drawer at a time.
Never
Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.
- Always monitor your child’s activity when in the nursery.
- allow standing in drawers.
Do not
- allow standing on top of this product.
Do not
- Accessory items must be securely fastened to this product according to the instructions provided
with those items.
- To avoid head injury, do not allow children to play underneath open drawers.
- Do not leave drawers open when in use.
ASSEMBLY, CARE AND MAINTENANCE
CAUTION: Do not use a power screwdriver as it can cause screws to break or strip.
- T
o protect finished parts during assembly, please place them on a soft, non-abrasive surface
toavoid damaging the finish.
- Care should be taken when unpacking and assembling the product.
- Inspect the product periodically, contact us for replacement parts orquestions.
- Do not store this product or any parts in extreme temperatures and conditions such as hot attic or
a damp, cold basement..
- To clean surface, use only water on damp cloth then a dry cloth to preserve the original finish.
- use abrasive chemicals or window cleaners as it will scratch the surface and coulddamage
Do not
the protective coating.
- Lift product when moving on carpeting to prevent leg breakage.
- Avoid using a vaporizer near furniture as it will cause wood to swell and finish to peel.
do not
LIMITED WARRANTY
Page 3
Page 4
BACK PANEL
TOP CROSS RAIL
BOTTOM CROSS RAIL
MIDDLE CROSS RIAL
LEFT SIDE PANEL
TOP BACK PANEL
MIDDLE PANEL
SUPPORT POST
UPPER & LEFT DRAWER FRONT
RIGHT SIDE PANEL
TOP PANEL
UPPER & RIGHT DRAWER FRONTL
UPPER LEFT DRAWER SDIE
UPPER RIGHT DRWER SIDE
DRAWER BOTTOM PANEL
Page 5
UPPER DRAWER BACK
LOWER & LEFT DRAWER FRONT
LOWER & RIGHT DRAWER FRONT
LOWER & DRAWER LEFT SIDE
LOWER & DRAWER RIGHT SIDE
LOWER DRAWER BOTTOM
Page 6
- Thread 6 CAM BOLTs (1) to middle of BACK PANEL (A), TOP CROSS RAIL (B), BOTTOM CORSS
RAIL (C), and MIDDLE CROSS RAIL (D).
Page 7
- Insert 2 CAM LOCKS (3) to MIDDLE PANEL (E). (make sure cam arrow is pointing
to short edge)
- insert 3 WOOD DOWELS (2) into TOP CROSS RIAL (B), AND BACK PANEL (E).
- Attach BACK PANEL (A) AND TOP CROSS RIAL (B) to MIDDLE PANEL (E) BY TURNING
CAM CLOCKWISE.
Page 8
- Insert 4 CAM LOCKS( 3) to MIDDLE PANEL (E).
- Insert 2 WOOD DOWELS (2)
- Attach 2 TOP CROSS RAILSES (B), 2 MIDDLE CROSS RAILS (D), and BOTTOM RAIL (C)
by turning the cmas clockwise.
Page 9
- Thread 20 CAM BOLTS (1) to LEFT PANEL (F), RIGHT PANEL (G), and TOP PANEL (I)
20
Page 10
- Insert 14 CAM LOCKS (3) to 2 TOP CROSS RAILS (B), 2 MIDDLE CROSS RAILS (D), and BOTTOM
CROSS RAIL (C).
- Insert 14 WOOD DOWELS (2) into ends of 2 TOP CORSS RIALS (B), 2 MIDDLE CROSS RIALS (D), and
BOTTOM CROSS RAIL (C).
- Attach LEFT PANEL (G), and RIGHT PANEL (F) to partially assembled unit by turning the CAM
LOCK (3) clockwise.
Page 11
- Attach SUPPORT LEG (H) to MIDDLE PANEL (E) with 1 BOLT (4) and 2 WOOD
DOWELS (2) as shown. (Use ALLEN KEY (5) to tighten the bolt.)
NOTE - The SUPPORT LEG (H) and SIDE PANELS (G & F) are equipped with
adjustable levelers. Once assembly is coplete and the unit is in the
desired location, rotate the adjustable clockwise or counterclockwise
until it rests evenly on the oor.
Page 12
7
- Insert 6 CAM LACKS (3) and 6 WOOD DOWELS (2) in LEFT SIDE PANEL (G), RIGHT SIDE PANEL
(F), MIDDLE PANEL (E).
- Carefully position the TOP PANEL (I) over assembly and lock into place using the locatin
WOOD DOWELS (2).
- Attach TOP PANEL (I) to LEFT PANEL (G), RIGHT SIDE PANEL (F), and MIDDLE PANEL (E) by
turning the cams clockwise.
- Insert 4 WOOD SCREWS (6) into BOTH TOP CORSS RAILS (back and front) and attach to
TOP PANEL (I).
Page 13
10
- Attach TOP BACK PANEL (J) TO BACK OF CHST JUSING 16 ROUND HEAD SCRES (7).
Page 14
9
- Position and attach UPPER LEFT DRAWER SIDE (M),
and UPPER RIGHT DRAWER SIDE (N) by using 4 OF 1”
(25mm) SCREWS (6) provided to UPPER LEFT
DRAWER FRONT (K).
- Carefully slide DRAWER BOTTOM (0)
into grooves of DRAWER SIDES and
DRAWER FRONT.
- Position and attach DRAWER BACK (P)
to DRAWER SIDES using 4 of 1” (25mm)
screws (6) providevd.
- Repeat same step for upper right side drawer.
Page 15
10
- Position and attach LOWER LEFT DRAWER SIDE (S),
and LOWER RIGHT DRAWER SIDE (T) by using 4 OF 1”
(25mm) SCREWS (6) provided to LOWER LEFT
DRAWER FRONT (Q).
- Carefully slide DRAWER BOTTOM (0)
into grooves of DRAWER SIDES and
DRAWER FRONT.
- Position and attach LOWER DRAWER BACK (U)
to DRAWER SIDES using 4 of 1” (25mm)
screws (6) providevd.
- Repeat same steps for lower right side drawer.
Page 16
- Assemble the drawers tothe case as per below conguration.
- Holding the drawer on a downward sloping angle, rest of drawer sides to the
correspoinding drawer runners pre-assembled
- Carefully push the drawer forward makin sure the rollers are. inside the track.
- Assemble the rest of the drawers.
- Position dresser in your room
and install tip-over restraint as per
instructions included in the hardware kit.
Page 17
Loading...