Ebern Designs W005373787 General Instructions

Page 1
PRECAUTIONS
FOR SAFE USAGE PLEASE OBSERVE THE FOLLOWING:
GARMENT RACK DOUBLE SHELF
FOR INDOOR STORAGE USE ONLY
• Keep product on a flat, stable surface.
• Do not use on balconies; especially in high-rise buildings.
• Do not use near stove or other sources of fire.
• Please observe weight tolerance and do not overload product.
• Balance hanging objects evenly on product for even weight distribution.
• Please check that screws are properly tightened after installation. Screws may loosen over time; re-tighten as needed.
When moving products:
• Remove all items and lift evenly from both sides.
• Hold lower pipes when moving up and down steps.
For safety:
• Do not allow children to play with product.
• Do not hang on product or apply unnecessary weight.
• Pipe edges may be sharp: be careful not to cut hands
To avoid damage to product:
• Keep away from direct sunlight or high humidity.
• Wipe away any water, oil, or soap immediately.
• Do not place hot or wet items on the product.
• Do not place stickers or tape on product.
• Wipe off any excess grease from pipes
GENERAL INSTRUCTIONS
Thank you for purchasing this product. Please read these instructions carefully before use. Keep these instructions for future reference.
REQUIRED TOOL: NO. 2 PHILLIPS HEAD SCREWDRIVER
Assembly by 2 people is recommended
WARNING
MATERIALS
WEIGHT CAPACITY (
* WEIGHT CAPACITY IS MEASURED VALUE, NOT GUARANTEED VALUE. * PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
kg/lbs) Hanger Rod: 10kg/22lbs Upper Board: 5kg/11lbs Lower Board: 10kg/22lbs
In order to avoid damage, do not use an impact driver.
64cm W x 40cm D x 151.2cm H PRODUCT SIZE (cm/in)
25.5" W x 15.75" D x 59.5" H
Epoxy coated steel and finished particleboard
CLEANING METHOD
• For hard to remove stains, wipe with diluted dish soap on damp cloth and dry thoroughly
• Do not use cleaning products such as alcohol, gasoline, bleach or detergent powder.
TO MAINTAIN HIGH PERFORMANCE OF THE PRODUCT, PLEASE MAKE SURE TO OBSERVE THE FOLLOWING:
PARTS
front
Upper Board (1)
• PLEASE CONFIRM THE FOLLOWING PARTS ARE INCLUDED BEFORE ASSEMBLING.
• PACKAGING MATERIAL IS NOT MARKED. EXTRA HARDWARE INCLUDED FOR CONVENIENCE.
The side with the
hole is the underside
underside
The side with the rounded
Hanger Rod (1)
corners is the front
Rack Pipe (1)
front
Lower Board (1)
2 holes
The side with the rounded
corners is the front
U-Shaped Pipe (1) Felt Stickers (5)
Upper Pipes (2) Lower Pipes (2)
Covering Stickers (5)
This part is already installed in
to the hanger rack pipes.
Long Bolts (4)
Short Bolts (5)
Flat Screws (5)
Screws (5)
Nuts (5)
Spacers (5)
Screwdriver (1)
Page 2
ASSEMBLY METHOD
• RECOMMENDED TO ASSEMBLE WITH 2 PEOPLE
• IF ASSEMBLING INDOORS, BE WARY OF UNEVEN SURFACES SCRATCHING THE FLOORING.
• GLOVES SUGGESTED TO AVOID INJURY DURING ASSEMBLY.
• ASSEMBLE NEAR LOCATION OF INTENDED USE.
1
Insert the Upper Pipes and adhere Felt Stickers to bottom of Lower Pipes. Use the diagram below as reference and be mindful of the direction the pipes are facing, with indented holes facing out of Upper Pipes and 2 holes facing back of Lower Pipes.
CAUTION
Be mindful of your fingers
when inserting pipes.
The screw holes with the
indented surface are the
outer sides.
The side with the one
screw hole is the front end.
Upper Pipes (left + right are the same)
The screw holes with the
indented surface are the
outer sides.
The side with the two screw
holes is the back end.
2
Install the U-Shape Pipe and Hanger on
Loosely place screws
Left
Spacers (2)
Place spacers between Upper
Pipe and Hanger Rod.
Spacer
Pipe
Hanger
1
Hanger Rod (1)
U-Shaped Pipe (1)
Right
Long Bolts (2)
Short Bolts (4)
*The long bolts are already attached on the hanger. Please remove before assembling.
U-Shaped Pipe
Lower Pipe
Short Bolts
3
Attach the Rack Pipe on to the Board. Fasten screws from below.
Secure the screws tightly.
Board (1)
front
Lower Pipes (left + right are the same)
4
Secure the screws into the
U-shaped pipe before screwing
Long Bolts into Lower Pipes.
Attaching the Upper Board:
1. Insert the Nut from the bottom and secure the Flat Screw from the top while holding the Nut in place with the Screwdriver.
2. Adhere Covering Stickers to hide screw holes.
Felt Stickers (4)
Attach section to section with bolts and screws.
3 2
Flat Screws (4)
Nuts (4)
Upper Board (1)
Screwdriver
3
Part
front
Covering Stickers (4)
Part
2
5
Make sure all screws are tightly secure.
Rack Pipe (1)
Screws (2)
*The 2 rounded corners should be facing forward.
Be mindful of direction when
placing spacers.
Spacer
Pipe
Hanger
Screws (2)
Spacers (2)
front
Long Bolts (2)
*The long bolts are already attached on the hanger. Please remove before assembling.
WARNING
• Tighten and secure screws properly
• Make sure product is straight and sturdy
• All feet are equally on the ground
Loading...