Page 1
Label Picture Description QTY
A Backrest 1
B Left Armrest 1
C Right Armrest 1
D Foot Rest 1
E Seat Panel 1
Caution : You should read this carefully before you proceed
Barstool
Page 1 OF 8
Page 2
Label Picture Description QTY
①
Allen Key 1
② Bolt (M6*65MM) 3
③
Bolt (M6*40MM) 9
④ Bolt (M6*20MM) 9
⑤ Bolt Cap 11
⑥ Washer 19
Before Beginning Assembly:
Page 2 OF 8
Page 3
Step 1
Place the Backrest (A) and the Seat Panel (E) on a clean, flat surface.
Use bolts (3) and washers ( 6) to connect the Seat Panel (E) to the Backrest (A).
Note: Do not use the Allen Key (1) to tighten the bolts completely until all parts are
assembled.
Page 3 OF 8
This Barstool has multiple parts and may require up to 45minutes to assemble.
To give you an overview of the Barstool parts, the above picture is to help you put the
various parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.
FRONT FACING
Page 4
Step 2
Step 3
Place the Left Armrest (B) on a clean, flat surface.
Use bolts( 3 )and washers( 6) to connect the Left Armrest (B) to the Seat Panel (E).
Note: Do not use the Allen Key (1) to tighten the bolts completely until all parts are
assembled.
Place the Right Armrest (C) on a clean, flat surface.
Use bolts（3）and washers ( 6） to connect the Right Armrest (C) to the Seat Panel (E).
Note: Do not use the Allen Key (1) to tighten the bolts completely until all parts are
assembled.
Page 4 OF 8
Page 5
Step 5
Step 4
Page 5 OF 8
Use bolts (2) and washers (6) to connect the back end of the Left Armrest (B) to the
Backrest (A). Then use bolts (2) and washers ( 6) to connect the back end of the Right
Armrest (C) to the Backrest (A).
Note: Do not use the Allen Key (1) to tighten the bolts completely until all parts are
assembled.
Place the Left Armrest (B) on a clean, flat surface.
Use bolts（4）and washers (6) to connect the Foot Rest (D) to the Left Armrest (B) , the
Right Armrest (C) and the Backrest (A).
Note: Do not use the Allen Key (1) to tighten the bolts completely until all parts are
assembled.
Page 6
Step 6
Page 6 OF 8
Place the barstool on a LEVEL SURFACE to check for wobbles.
If it wobbles lift the barstool to some 20cm to 30cm height from the ground.
Keep your feet and toes well away from the drop zone.
Drop the barstool freely and vertically with the four legs, hitting the ground, all at the same time.
This Drop Test will help to ensure that all the bolts and gaps reach full alignment status.
Test again for evenness on a LEVEL SURFACE.
If no wobbles are found, slowly and steadily turn the barstool upside down.
Then proceed to tighten all bolts in a sequential manner.
CAUTION : When tightening these bolts, tighten sequentially.
DO NOT tighten any bolt fully and then move on to the next one.
This could cause the frame to warp.
If it still wobbles after tightening, loosen the bolts and execute th esame drop test again.
WARNING!! IF THE BARSTOOL IS NOT STABLE , IT COULD LEAD TO DAMAGE OF THE
PRODUCT.
Page 7
Step 7
Page 7 OF 8
Cover all bolts with Bolt Caps (5).
Your Barstool is ready for use.
Step 8
Page 8
Page 8 OF 8
Loading...