Page 1
Label Picture Description QTY
A Headboard 1
B Right Headboard Foot 1
C Left Headboard Foot 1
Assembly Instructions
TWIN BED
NOTE: This Bed is NOT a TOY.
Keep your child / children at bay during the assembly process.
The BED is HEAVY.
To prevent injury to yourself or damage to the product a minimum of two
adults are required whenever moving or lifting the product.
Part List
Caution: You must read this before you proceed
Page 1 OF 10
Page 2
D Footboard 1
E Side Rail(Labelled 'E') 2
F Side Rail(Labelled 'F') 2
G
Headboard Support
Rail
1
H Side Cleat 4
I Center Side Cleat 2
J Leg 2
K
Cross Center Support
Rail
1
L Slat 12
M Z-shaped Support Leg 2
N Straight Connector 4
Label Picture Description QTY
① Bolt(M8*16mm) 9
② Bolt(M6*35mm) 13
Hardware
Page 2 OF 10
Page 3
③ Bolt(M6*16mm) 13
④
Bolt(M8*25mm) 5
⑤
Bolt(M8*50mm) 9
⑥
Bolt(M8*30mm) 5
⑦
Bolt(M6*25mm) 3
⑧
Spring Washer 9
⑨
Washer 15
⑩
Allen Key(M6) 1
⑪
Allen Key(M8) 1
⑫
Side Slat Plug 28
Before
Beginning
Assembly:
Assembly Preparation
X2X2X4
X2
X2
X12
X2
X4
X9
X13
X13
X5
X9X5X3
X9
X15
X28
Page 3 OF 10
Page 4
This Bed has multiple parts and may require up to 60 minutes to
assemble.
To give you an overview of the Bed parts, the above picture is to help
you put the various Bed parts into perspective.
Please read through the instructions below to familiarise yourself with
the parts and steps before assembly.
Assembly Steps
Overview
FRONT FACING
Headboard(A)
Right Headboard Foot(B)
Side Rail(E)
Side Rail(F)
Left
Headboard
Foot(C)
Footboard(D)
Leg(J)
Slat(L)
Z-shaped Support Leg(M)
Headboard Support Rail(G)
Side Rail(F)
Page 4 OF 10
Page 5
Step 1
Step 2
Step 3
Align the mounting position of Right Headboard Foot(B) to the back of
Headboard(A) as shown.
Attach Right Headboard Foot(B) to Headboard(A) using Bolts(⑤) and
Washers(⑨) with Allen Key(⑪).
Then, repeat the same step to assemble Left Headboard Foot(C) to
Headboard(A).
Note: Remove the Cover before assembling Headboard Foot.
Do not overtighten.
Attach Headboard Support Rail(G) to Right Headboard Foot(B) and Left
Headboard Foot(C) using Bolts(③) with Allen Key(⑩).
Unpack and place all parts for clear visibility.
X2
X2X4X2
X2
X12
X2
X4
Page 5 OF 10
Page 6
Step 4
Step 5
Step 6
Align the mounting position of Side Cleat(H) and Center Side Cleat(I) to
Side Rail(E) and Side Rail(F).
Attach Side Cleat(H) and Center Side Cleat(I) to Side Rail(E) and Side
Rail(F) using Bolts(②) with Allen Key(⑩).
Repeat same step to attach Side Cleat(H) and Center Side Cleat(I) to
remaining Side Rail(E&F).
Note: After assembling, the mounting positions should face upside.
Place the Side Rail(E&F) face skywards onto a clean, soft surface to
avoid any scratches or damages to the product.
Attach the first and fifth mounting position of Straight Connector(N) to
Side Rail(E) and Side Rail(F) using Bolts(①) with Allen Key(⑪).
Repeat same step to assemble remaining Side Rail(E&F).
Page 6 OF 10
Page 7
Step 7
Step 8
Align the mounting position of Straight Connector(N) on assemble Side
Rail Frame to Right Headboard Foot(B).
Attach Straight Connector(N) on assemble Side Rail Frame to Right
Headboard Foot(B) using Bolts(④), Spring Washers(⑧) and
Washers(⑨) with Allen Key(⑪).
Repeat same step to assemble the other Side Rail Frame to Left
Headboard Foot(C).
Place the Footboard(D) upside down as pix shown.
Attach Leg(J) to Footboard(D) using Bolts(⑤) with Allen Key(⑪).
Note: Turn the Footboard(D) rightside up after assembling.
Attach Z-shaped Support Leg(M) to assembled Side Rail Frame(E&F)
using using Bolts(③) with Allen Key(⑩).
Repeat same step to assemble the other Z-shaped Support Leg(M) to
the other assembled Side Rail Frame(E&F).
Note: Turn assembled Side Rail Frame(E&F) rightside up after
assembling.
Page 7 OF 10
Page 8
Step 9
Step 10
Attach Cross Center Support Rail(K) to Center Side Cleat(I) using
Bolts(⑦) with Allen Key(⑩).
Align the mounting position of Straight Connector(N) on assemble Side
Rail Frame to Footboard(D).
Attach Straight Connector(N) on assemble Side Rail Frame to
Footboard(D) using Bolts(⑥), Spring Washers(⑧) and Washers(⑨) with
Allen Key(⑪).
Repeat same step to assemble the other Side Rail Frame to
Footboard(D).
Do not fully tighten the Bolts.
Page 8 OF 10
Page 9
Step 11
Step 12
Now tighten all Bolts fully at all joints in a sequential manner.
Your Bed is ready for use.
Note: After assembly and before using the bed, inspect to make
sure all parts are properly connected and securely fastened.
Now tighten all Bolts fully at all joints in a sequential manner.
Then, align assembled Slat(L) to the mounting position of Side Cleat(H),
Center Side Cleat(I) by pressing with hands.
Note: If necessary, tap assemble slat to ensure it is fully slotted into
position.
Page 9 OF 10
Page 10
Page 10 OF 10
Loading...