Page 1
OFFICE DESK
Thank you for purchasing this OFFICE DESK！
Before you st
art, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
Hardware:
A
B
C
Bolt M8x60mm x2
Bolt M8x40mm x2
Bolt M8x30mm x2
Component:
D
E
F
G
H
Bolt M8x10mm x16
Washer x2
Flat Washer x20
Plastic Cap x2
Allen Wrench x1
Glass Top x1
1
Right Leg x1
3
(with three pre-drilled holes) (with one pre-drilled hole)
5
Page 1 of 4
Central Rail x1
Drawer Box x1
2
Left Leg x1
4
Page 2
OFFICE DESK
STEP 1:
Place the Left Leg (4) to the Central Rail (5) as shown.
Please make sure that the concave surface of each Washer (E) faces to the head of each Bolt (A) when connecting.
Attach them by using Bolts (A) and Washers (E) through the pre-drilled holes on the Central Rail (5) and the Left Leg (4).
Tighten Bolts (A) with the Allen Wrench (H). Then cover the Plastic Cap (G) to the head of Bolt (A) as shown.
Repeat the same steps for assembling the Right Leg (3) to the Central Rail (5).
Notice：
Please make sure that the concave
surface of each Washer (E) faces to
the head of each Bolt (A) when connecting.
Ax2 Ex2 Gx2
Hx1
Hardware & Tool required
STEP 2:
Please put the Glass Top (1) upside down on a flat and smooth surface as shown .
Attach the assembled Central Rail (5), Right Leg (3) and Left Leg (4) into the bottom of Glass Top (1) by using Bolts (D)
and Flat Washers (F).
Use the Allen Wrench (H) to tighten the Bolts (4) clockwise until secure.
Dx16 Fx16 Hx1
Hardware & Tool required
Page 2 of 4
Page 3
OFFICE DESK
STEP 3:
In order to properly attach the Drawer Box (2) to the side of the Right Leg (3), take out the extra space before leg. It will be
necessary to remove the two drawers from the Drawer Box (2). Please follow the following steps for drawer removal.
A, Open the drawer fully.
B, Locate the black quick disconnect levers on the right and left-hand slides.
C, Simultaneously press the quick disconnect levers while pulling out the drawer. As shown, the right-hand level is pressed
down, while the left-hand lever releases by pulling up.
Left-Hand Slide:
Pull lever up
Right-Hand Slide:
Press lever down
STEP 4:
Carefully turn over the assembled desk.
Attach the Drawer Box (2) without drawers to the Right Leg (3) by using Bolts (C) and Flat Washers (F) through the
pre-drilled holes on the inside of the right side panel of the Drawer Box (2) and Right Leg (3).
Do not fully tighten the Bolts (C) at this time.
Attach the Drawer Box (2) to the Central Rail (5) by using Bolts (B) and Flat Washers (F).
Use the Allen Wrench (H) to tighten Bolts (B) and Bolts (C) clockwise until secure.
Bx2 Cx2 Fx4
Page 3 of 4
Hx1
Hardware & Tool required
Page 4
OFFICE DESK
STEP 5:
In order to return the two drawers into the Drawer Box (2).
A, Align drawer with drawer slides.
B, Move silver metal carrier fully forward in slide.
C, Gently push drawer into the drawer box.
Silver Metal Carrier Align drawer with drawer slides. Push drawer into
the Drawer Box (2) until clicking sound is heard
and slides are locked together
Assembly is completed. The desk is ready to enjoy now!
Page 4 of 4
Loading...