INSTALLATION INSTRUCTIONS
1
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your , please make sure that
you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture
configuration are made.
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans
la configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations
that may occur. It must be understood that common sense, caution and
care, are factors that can’t be built into any product. These factors must
be supplied by the person(s) caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux.
Do not install any fixture assembly closer than 6 inches from any
curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute
surface combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.”
COLLECTION
ModPLUS
WHAT WE PROVIDE
• Mounting
Hardware
APPLICATION
Ceiling Fixture
WHAT YOU NEED
•
• Wire Cutters
• Mounting Bracket
• Wiring Supplies as Specified
• LED
Recommended Dimmers
LEVITON Decora Sureslide 6672
LEVITON Decora Sureslide 6674
LUTRON Maestro CL MACL-153M
LUTRON Diva DVCL-153P
LUTRON Skylark CL SCL-153 or SCL-153P
Screwdriver
by Electrical Code
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
Recognized.
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
1
2
4
2
3
ATTACH MOUNTING BRACKET
If there is an existing fixture remove it.
Install the mounting bracket to the J-Box with
the supplied screws.
MAKE WIRE CONNECTION
Expose the supply wires from the J-box.
Gently pull the supply wires through the hole in the
mounting bracket. Connect the black supply wire to
the black fixture wire. Secure with the supplied wire nuts.
Connect the white supply wire to the white fixture wire.
Secure with the supplied wire nuts. Attach the green
J-Box wire around green hexagon screw or connect it to
the green supply grounding wire of the
all
wires with electrical tape (not supplied).
Tuck all wires carefully into the J-Box.
MOUNT FIXTURE
Align the fixture to the mounting bracket.
Rotate the fixture in the indicated direction to lock it
into the mounting bracket.
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION
fixture. Secure
If the fixture is to be removed or replaced,
please ensure that the electricity is
CAUTION
switched off and that the fitting is cool
before touching it.
Loading...