ASSEMBLY INSTRUCTIONS
2 Drawer Cabinet
For fastest service on claims, requests for replacement parts, or
questions, please visit our website at
Cabinet top maximum
weight capacity
=40lbs
Drawer maximum
weight capacity
=20lbs
2 OF 12
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED.
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- HAVE THE TOOLS BELOW BEFORE YOU BEGIN ASSEMBLING.
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
- DO NOT SHIFT OR DRAG THE PRODUCT AFTER ASSEMBLY.
- THE FOLLOWING TOOLS ARE NOT INCLUDED.
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
- DO NOT USE FURNITURE WAX OR POLISH AS THE UNIT
IS FINISHED WITH A PROTECTIVE CLEAR LACQUER.
IF YOU ARE MISSING ANY OF THE PARTS ABOVE, OR IF YOU HAVE A DAMAGED PART, PLEASE VISIT WWW.COMFORTPRODUCTS.NET/SUPPORT
REFERENCE THE MODEL # ON THE FRONT OF THIS MANUAL. SIMPLY COMPLETE THE INFORMATION, INCLUDING THE PART YOU NEED. THE PART
WILL NORMALLY BE SHIPPED WITHIN 48 HOURS.
3 OF 12
Fix sixteen Wood Dowels (1) to Panel (A), Panel (B), Panel (H),
Panel (I), Panel (K) & Panel (L) using rubber hammer.
into predrilled holes .
4 OF 12
Screw two Drawer Slides (3-CL) to the Left Side Panel (A) using four Euro Screws (4).
Then screw two Drawer Slides (3-CR) on to the Right Side Panel (B) using four Euro Screws (4).
Screw bottom Panel (D) to Left Side Panel (A) & Right Side Panel ( B)
with four Unitar Screws (5) using predrilled holes.
Attach four Bottom Legs (E) to Bottom Panel (D) with eight CSK Screws (6)
using predrilled holes.
Press four Cams (7) into the holes as shown, making sure the arrows are pointing up.
Attach Desktop (C) to cabinet by aligning the Minix Bolts (2) into predrilled holes.
Turn the cams clockwise half a turn to lock into place.
Attach the Back Panel (N) to the cabinet by aligning Back Panel with edges of the top and
Panel (N) to the cabinet. (DO NOT Hammer too hard; tight nails will cause drawers to be hard to
open).
Small drawer assembly :
then press Cams (7) to the bottom of the holes and making sure the arrow on the top each
Large drawer assembly :
Next attch two LG side Drawer Panel (K) and Panel (I) to LG Drawer Front (G) aligning
Slide drawer Bottom Panel (Z) into both big and small drawers using the grooves
Small drawer assembly :
Attach SM back Panel (J) to SM side drawer Panels (H) and Panel (I) by aligning grooves
Large drawer assembly :
Attach LG back Panel (M) to LG side drawer Panel (L) and Panel (K) by aligning grooves with
Attach aluminium handle and two Handle Screw (10) to each drawer.
Attach two Drawer Slide (11-DR) and Drawer Slide (11-DL) to the bottom of each
drawer using eight Short Screws (12).
Aligning the sliders, insert the large drawer into the bottom slot of the cabinet and the
small drawer into the upper slot.
DO NOT stand on the desk. Do not use the desk as a stepladder.
•
DO NOT use the desk unless all bolts and screws are firmly secured.
•
Every 6 months, check all bolts and screws to ensure they are tight.
•
This product is California 93120 Compliant for Formaldehyde.
•
12 OF 12
Loading...