Page 1
STEP 13
STEP 14
Attach Back Panel (M) to the back of
assembled unit using Power Pin (6).
Unfold Bin (9) and slide into the shelf.
(9)
Assembly Instruction
Multipurpose Home Office
Computer Writing Desk w/Bin
Approx. 30 minutes
(6)x12pcs
Recommended Maximum Weight
10
15
10
Recomm. 2 Person
Tool RequiredTool Required
WARNING:
>This unit has been designed to support the
maximum loads shown. Exceeding these
load limits could cause sagging, instability,
product collapse, and/or serious injury.
*Unit in pound (lbs)
8
>DO NOT allow children to climb on unit.
>Put heavier items on lower shelves.
1
Page 2
No Hardware List Qty
1
2
3
Screw
Dowel
Nail Leg
18pcs
12pcs
6pcs
No QtyParts List
Top Panel 1
A
Top Panel 2
B
Left Side Panel
C
1pc
1pc
1pc
STEP 11
Attach Panel (A) to Panel (C)&(D) and tighten Cam-Lock Nut (4) using screwdriver.
Cam-Lock Nut
4
Cam-Lock Screw
5
Power Pin
6
Drawer Slide
7
Keyboard Screw
8
Non-Woven Bin
9
Right Side Panel
B
7pcs
7pcs
12pcs
1set
8pcs
1pc
D
Side Support Panel
E
Top Support Panel 1
F
Top Support Panel 2
G
Bottom Side Panel
H
Shelf Panel
I
Bottom Panel
J
Back Panel
K
Keyboard Panel
L
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
F
G
Back Cover
M
1pc
STEP 12
E
12.1 Upright the unit and slide in Keyboard Panel (L).
A
I
L
L
K
D
M
H
J
C
9
USEFUL HINTS BEFORE YOU START:
1. Read each step carefully before starting.
2. It is important that each step is performed in correct order to avoid difficulties.
3. Identify, sort and count the parts before assembly.
4. Assemble your furniture on packaging cardboard to prevent scratch or damage.
12.2 Attach Panel (B) to Panel (E)(F)&(G) and tighten Cam-Lock Nut (4) using
screwdriver.
5. Clean the product with mild cleanser using soft damped cloth. Do not use harsh or abrasive cleanser.
6. Using uncompatible hardware might cause damage to product.
2
7
Page 3
STEP 9
STEP 1
Attach Panel (C) to the assembled unit using Screw (1).
(1)x4pcs
Insert Dowel (2) and Cam-Lock Nut (4) into the pre-drilled holes on Panel
(C,D,E,F,G&H).
(4)x2pcs
(2)x2pcs
Arrow on Cam-Lock
Nut (4) should be
pointing towarcls
holes.
4
STEP 10
10.1 Attach Panel (G) to Panel (F) using Screw (1).
10.2 Attach Panel (F)&(G) to Panel (A) using Screw (1).
(1)x2pcs
(1)x4pcs
STEP 2
Install Nail Leg (3) to the bottom of
Panel (C)(D)&(H) using rubber mallet.
(3)x2pcs
STEP 3
Screw Cam-Lock Screw (5) into
the pre-drilled holes on Panel (A)(B)&(I).
(5)x7pcs
6
3
Page 4
STEP 4
STEP 6
STEP 7
Fix Drawer Slide (7) to Panel (L) using Screw (8).
Note: Please make sure L&R Side of Drawer Slide (7) before attach it.
(8)x4pcs
Front Side
Attach Panel (E) to Panel (I) using
Screw (1).
(1)x2pcs
Attach Panel (J) to Panel (H) using
Screw (1) and tighten Cam-Lock Nut (4)
on Panel (H) using screwdriver.
(1)x2pcs
STEP 5
Fix Drawer Slide (7) to Panel (C)&(D) using Screw (8).
Note: Please make sure L&R Side of Drawer Slide (7) before attach it.
(8)x4pcs
STEP 8
Attach the assembled unit to Panel (D)&(K) using Screw (1), as shown.
(1)x6pcs
4
5
Loading...