Page 1
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Hardware Package (included):
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Plate (A)
Mounting Plate (A)
House Grounding Wire
Outlet Box
Green Grounding Screw (C)
Fixture Grounding Wire
Mounting Screw (B)
Headless Screw (D)
Lock Nut (E)
Mounting Screw (B)
Green Grounding
Screw (C)
Wire Nut (F)
Fixture Wire
IMPORTANT:
The sensor has an excellent photocell function
to enable the light to turn on at dusk and off at
dawn automatically.
Headless
Screw (D)
Lock Nut (E)
Photocell
Wire Nut (F)
Ball Nut (G)
Fixture
Rubber Pad (H)
Rubber Pad(H)
Ball Nut(G)
Bulb Type A Max.100W
(not included)
Installation Steps
Turn off the power at fuse or circuit box.
1.
Thread two headless screws through the mounting plate, and then secure them with four lock nuts (two on each side
of the mounting plate). Adjust the length of the headless screws if necessary.
Note: Make sure that the headless screws are lined up horizontally to make the fixture level.
2. Attach the mounting plate to the outlet box by using two mounting screws.
3. Pull out the source wires from the outlet box. Make wire connections using wire nuts as follows:
---Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source.
---Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source.
---Attach the fixture grounding wire (usually green insulation or bare wire) to the mounting plate with the green
grounding screw, and then connect it to the house grounding wire with the wire nut.
Carefully put the wires back into the outlet box.
Bulb Type A Max.2-40W
(not included)
Page 2
4. Attach the fixture to the mounting plate by inserting headless screws into holes on back plate, and then secure it
with two rubber pads and two ball nuts.
NOTE:With silicone caulking compound, caulk completely around where the back plate meets with the
wall surface to prevent water from seeping into the outlet box.
5. Install a bulb (bulbs) (not included). Check relamping label at socket area or packaging for maximum allowed wattage.
Turn on the power at fuse or circuit box.
Operation the Unit Without Photocell
Photocell
Black Wires From Photocell
White Wires From Photocell
Red Wires From Photocell
Wire Nuts
Wires From Fixture
Wires From
Main Power
Pigtail
Wires From Fixture
1. Turn off the power at the fuse or circuit box before starting installation.
White Pigtail
Fig.
1
2. Loosen the wire nuts connected with the wires from photocell. (See Fig.1)
Note: Do not move the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire nuts: (See Fig.2)
a. The black wire from the fixture to one end of the black pigtail.
b. The white wire from the fixture to one end of the white pigtail.
c. The other end of the black pigtail to the black wire from the power source.
d. The other end of the white pigtail to the white wire from the power source.
Put all wires back into the back plate of the fixture.
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Plate (A)
Mounting Screw (B)
Green Grounding
Screw (C)
Headless
Screw (D)
Lock Nut (E)
Wire Nut (F)
Wire Nut
Ball Nut (G)
.2
Fig
Rubber Pad (G)
Assembly Kit (1 SET)
A: 7"
B
B: 4-7/8"
B
C: 4"
A
C
A
C
A: 12"
B: 4-7/8"
C: 4"
Loading...