Turn right (clockwise) to tighten
Page 4 of 6
#C x 8 pcs
#D x 8 pcs
#E x 8 pcs
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.
I. Align the two HB/FB feet (#5) with the pre-drilled holes underneath
the headboard (#1).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#D) onto the bolt (#C) and then the flat washer (#E) onto the
SAME bolt (#C), in that order.
III. Insert the bolt assemblies through the holes of the two HB/FB feet
(#5) and secure those bolts using the Allen wrench (#H) to lock
them with the headboard (#1).
IV. Repeat the process above to assemble the remaining two HB/FB
feet (#5) onto the footboard (#3).
Turn right (clockwise) to tighten
Page 5 of 6
#B x 2 pcs
#D x 2 pcs
#E x 2 pcs
#A x 8 pcs
#D x 8 pcs
#E x 8 pcs
I. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#D) onto the bolt
(#A) and then the flat washer
(#E) onto the SAME bolt (#A),
in that order.
II. Insert the bolt assemblies
through the right and left side
of the pre-drilled holes of the
headboard (#1) using the
Allen wrench (#H) but expose
about ½” of the bolts’ threads.
III. Mount the brackets on the
side rails (#2) onto the bolts
(#A) on each side of the
headboard (#1). Make sure all
the washers are in the
FRONT of the brackets. Use
the Allen wrench (#H) to
further tighten the bolts to
secure the two parts together.
IV. Repeat the process above to
assemble the other ends of
the 2 side rails (#2) onto the
footboard (#3).
I. Align the 2 support rail legs (#7)
with the pre-drilled holes of the
support rail (#4).
II. Prepare 2 bolt assemblies by
inserting FIRST the lock washer
(#D) onto the bolt (#B) and then
the flat washer (#E) onto the
SAME bolt (#B), in that order.
III. Insert the bolt assemblies
through the pre-drilled holes of
the support rail (#4) using the
Allen wrench (#H) to lock them
with the 2 slat support legs (#7).
Turn right (clockwise) to tighten
Adjust the levelers on the support rail legs
(#7) according to the ground level on Step 4.
#H
Turn right (clockwise) to tighten
Page 6 of 6
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs
I. Align the assembled
support rail (#4) with the
pre-drilled holes on the
center of the headboard
(#1) and the footboard (#3).
II. Prepare 4 bolt assemblies
by inserting FIRST the lock
washer (#D) onto the bolt
(#B) and then the flat
washer (#E) onto the SAME
bolt (#B), in that order.
III. Insert the bolt assemblies
through the brackets of the
support rail (#4) using the
Allen wrench (#H) to lock
them with the headboard
(#1) and the footboard (#3).
I. Prepare a bed slat using two slats (#6), one
center connector (#F) and two end caps
(#G). See diagram for the correct sequence
in connecting those parts.
II. Align the end caps (#G) with the pre-drilled
holes on each side of the side rails (#2) and
press firmly down on both end caps (#G) to
lock with the side rails (#2). Then press
firmly down on the center connector (#F) to
lock with the support rail (#4).
III. Repeat the process above to assemble the
remaining bed slats onto the side rails (#2)
and the support rail (#4).
IV. Make sure the bed is rested on a flat
surface and does not feel loose or wobbly.
If it does, double check that the
bolts/screws are secured and properly
tightened.
ASSEMBLY IS COMPLETED
Note: The correct position of the bed
slats should be arcing UPWARD when
placing on the rails.
#F x 13 pcs
#G x 26 pcs
Adjust the levelers according to the ground
level. To lower or to raise the support rail
legs, turn the levelers clockwise or
counterclockwise, respectively.
#H
Loading...