Page 1
G
&
N
I
F
T
H
G
I
L
A
N
S
EASY CONNECT®
INSTALLATION INSTRUCTIONS
E
C
L
A
I
R
A
G
E
S
N
&
E
V
!
INSTALL EASY CONNECT MOUNTING BRACKET:
STEP 1
Electrical
Box
Black (Live)
Green (Ground)
S
R
U
E
T
A
L
I
T
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) • 1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
Attach easy connect
mounting bracket
to electrical box with
electrical box screws
(not included).
L
Easy Connect
N
mounting
bracket
White
(Neutral)
EO -1
12/12
SAFETY PRECAUTIONS:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF
LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
NOTE: Product May Not Look Exactly As Shown In Figures.
STYLE #1
N
L
STYLE #2
CONNECT HOUSE WIRES
STEP 2 - Option 1
(N)
White
(Neutral)
(L)
Black
Green
(Ground)
N
L
(Live)
CONNECT LIGHT FIXTURE
STEP 3
(N)
White
(Neutral)
N
L
Green
(Ground)
(L)
Black
(Live)
Light
Fixture
STEP 5
Wheather
Resistant Caulking
Cap Nut
Wheather
Resistant Caulking
Option 2 - MULTIPLE ELECTRICAL BOX WIRES
Connect (push) electrical
wires from electric box
(house wiring) into correct
inserts. Black (Live),
White (Neutral),
Green (Ground)
Green
(Ground)
STEP 4
Connect (push) electrical wires
from fixture into correct inserts.
Black (live), White (neutral),
Green (ground)
Fixture
After Installation, seal around the
top and side perimeter between
the fixture and the wall surface
with weather resistant caulking.
The bottom should be left un-caulked
to prevent moisture build-up. Apply a
small amount of weather resistant
caulking around the side perimeter
between the cap nut and mounting plate.
L
(L)
Black (Live)
Stud
Or
Nipple
Star
Washer
Jumper Wire
N
(Neutral)
(N)
White
For multiple black (live) &
white (neutral) wires joined
in the electrical box
(house wiring), attach a single
“black” and “white” Jumper Wire
before connecting. Strip 7mm
Jumper
Wire
from a 6” Jumper Wires (AWG 12-24)
supplied. Then connect (push) wires
into correct inserts.
Tuck electrical wires into outlet box
Cap
and position fixture over studs or
Nut
nipple on mounting bracket assembly.
Secure fixture in place with star
washer(s) and cap nut(s).
Note: If required, assemble body and
spread the arms of the fixture out
evenly.
STEP 6 - Optional for some models (
STYLE#1
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: (613) 342-5424, Fax: (800) 263-4598
STYLE#1 - Install proper bulb type
and wattage. Slide the glass down.
Note: Refer to the style of assembly that matches the style of your fixture.)
STYLE#2 - Install proper bulb type
STYLE#2
and wattage.
Unscrew glass cylinder
to install bulb. Screw glass cylinder
back on to the fixture.
Loading...