Page 1
INSTALLATION INSTRUCTIONS
READ IMPORTANT SAFETY TIPS BEFORE PROCEEDING WITH INSTALLATION
INSTALLATION INSTRUCTIONS
READ IMPORTANT SAFETY TIPS BEFORE PROCEEDING WITH INSTALLATION
SAFETY TIPS
Turn fixture off! (Place wall switch
in off position, if fixture has built-in
switch or chain pull, switch or pull
chain so fixture is off.)
outlet box screws
1 2 3
ground wire
cross bar
ATTACH cross bar to outlet box with
outlet box screws (8-32 x 1/2, 2 slotted
screws provided).
mounting screws
outlet box
4
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
ground wire
wire connectors
(not provided)
CONNECT THE WIRES. NOTE: Attach
black fixture wire to black supply
wire, white fixture wire to white
supply wire. Do not mix them up.
Use wire connectors (not provided).
Connect bare fixture ground wire to
ground wire from outlet box. NEVER
CONNECT GROUND WIRE TO BLACK
OR WHITE POWER SUPPLY WIRES.
5
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
POSITION THE FIXTURE over the
outlet box and secure in place with
the mounting screw (1/4-20 x 1,1
provided). Screw lamp into lampholder.
Use lamp type and wattage specified on
fixture
mounting
screw
washer
cross bar
SAFETY TIPS
Turn fixture off! (Place wall switch
in off position, if fixture has built-in
switch or chain pull, switch or pull
chain so fixture is off.)
outlet box screws
1 2 3
ground wire
cross bar
ATTACH cross bar to outlet box with
outlet box screws (8-32 x 1/2, 2 slotted
screws provided).
mounting screws
outlet box
4
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
ground wire
wire connectors
(not provided)
CONNECT THE WIRES. NOTE: Attach
black fixture wire to black supply
wire, white fixture wire to white
supply wire. Do not mix them up.
Use wire connectors (not provided).
Connect bare fixture ground wire to
ground wire from outlet box. NEVER
CONNECT GROUND WIRE TO BLACK
OR WHITE POWER SUPPLY WIRES.
5
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
POSITION THE FIXTURE over the
outlet box and secure in place with
the mounting screw (1/4-20 x 1,1
provided). Screw lamp into lampholder.
Use lamp type and wattage specified on
fixture
mounting
screw
washer
cross bar
hood
reflector
Place diffuser on fixture base. Then place bar grill or frame
bar grill
(depending on fixture model) over diffuser and attach to base
with mounting screws (8-32x1/2, 4 combination head screw
provided). NOTE: On models with hood, attach diffuser to
base with one combination head mounting screw at center
top of base only. Place hood over diffuser and secure to base
with remaining three mounting screws. NOTE: Outdoor wall
fixture MUST be caulked with an acrylic caulk where base of
fixture meets mounting surface. This provides a water tight
seal when fixture is installed.
Clean only with mild soap and water. Avoid spraying with cleansers, insecticides, and pesticides that are petroleum
based hydrocarbon products. These will degrade Luminaire.
basediffuser
diffuser
wall
ON MODELS WITH HOOD, attach to wall with reflector up.
Hood is to be placed above reflector as shown.
hood
reflector
Place diffuser on fixture base. Then place bar grill or frame
bar grill
(depending on fixture model) over diffuser and attach to base
with mounting screws (8-32x1/2, 4 combination head screw
provided). NOTE: On models with hood, attach diffuser to
base with one combination head mounting screw at center
top of base only. Place hood over diffuser and secure to base
with remaining three mounting screws. NOTE: Outdoor wall
fixture MUST be caulked with an acrylic caulk where base of
fixture meets mounting surface. This provides a water tight
seal when fixture is installed.
Clean only with mild soap and water. Avoid spraying with cleansers, insecticides, and pesticides that are petroleum
based hydrocarbon products. These will degrade Luminaire.
basediffuser
diffuser
wall
ON MODELS WITH HOOD, attach to wall with reflector up.
Hood is to be placed above reflector as shown.
Loading...