EBAA Iron 1600 User Manual

Series 1600

Bell Restraint Harness for C900 PVC Pipe

Split Serrated Ring on the Plain End Pipe;

Split Non-Serrated Ring behind the Bell

Features and Application:

• For use on AWWA C900 PVC pipe bells

• Minimum 3 to 1 Safety Factor

Series 1610 on 10 inch AWWA C900 PVC Pipe.

Pressure Rating (AWWA C900 PVC)

Nominal

Pipe Size

Series

Number

Approximate

Shipping Weight

DR14

Class 200

DR18

Class 150

Class 100

4 1604 13.9 200 150 100 6 1606 20.7 200 150 100

8 1608 26.6 200 150 100 10 1610 54.1 200 150 100 12 1612 59.9 200 150 100

NOTE: For applications or pressures other than those shown, please contact EBAA

for assistance.

Packaged Items

DR25

• MEGA-BOND

Restraint Coating System For more on MEGA-BOND refer to www.ebaa.com

• Split design for ease of installation

• Constructed of ASTM A536 Ductile Iron

• Available in accessory packages

For use on water and wastewater pipelines subject to hydrostatic pressure and tested in accordance with either AWWA C600, C605 or ASTM D2774.

Sample Specication

Restraint for PVC pipe bell (AWWA C900) shall consist of the following: The restraint shall be manufactured of ductile iron conforming to ASTM A536. The restraint devices shall be coated using MEGA-BOND. (For complete

specications on MEGA-BOND visit

www.ebaa.com.) A split ring shall be used behind the pipe bell. A split serrated ring

shall be used to grip the pipe, and a sufcient

number of bolts shall be used to connect the bell ring and the gripping ring. The combination shall have a minimum working pressure rating shown in the Pressure Rating Table on the product brochure. The restraint shall be the Series 1600, as manufactured by EBAA Iron, Inc., or approved equal.

Serrated I.D.

Restraint Ring

Non-serrated I.D. Backup Ring

Thrust Bolt

EBAA IRON Sales, Inc.

P.O. Box 857, Eastland, TX 76448

Tel: (254) 629-1731

Fax: (254) 629-8931

(800) 433-1716 within US and Canada

contact@ebaa.com

www.ebaa.com

Series 1600 Submittal Reference Drawing

EBAA IRON

A B C D

Nominal

Pipe Size

Series

Number

Pipe O.D.

4 1604 4.80 6.75 9.25 13 2 - ¾ x 13 6 1606 6.90 8.75 11.25 18 2 - ¾ x 18

8 1608 9.05 12.25 14.75 18 2 - ¾ x 18 10 1610 11.10 14.20 16.85 22 4 - ¾ x 22 12 1612 13.20 16.90 19.45 22 4 - ¾ x 22

Installation Instructions

MADE IN USA

Maximum Bell

O.D. Cleared

NOTE: Dimensions are in inches and are subject to change without notice.

Max. Restraint O.D.

(Casing Clearance)

Overall Length

Thrust Bolt

(Number - Size)

The Series 1600 is designed for restraining push-on, C900 PVC pipe bells. It has a split, serrated restraint ring on the spigot and a split non-serrated ring behind the bell.

1. Assemble the push-on joint per the pipe manufacturer’s instructions.

5. Install both halves of the restraint ring at the proper location, tapping each half into place. Make sure that the complete ID of the ring is touching the pipe before installing the side bolts. Tighten the side bolts evenly to 60 ft-lbs torque (110 ft-lbs on 8 inch, 10 inch and 12 inch).

2. Install both halves of the non-serrated bell ring around the pipe behind the bell. Install the side bolts and tighten each to 60 ft-lbs (110 ft-lbs on 8 inch, 10 inch and 12 inch).

3. Slide the bell ring toward the bell so

that it ts snugly behind the bell.

6. Place nuts on the tie bolts and tighten until they are snug. Allow enough room on the tie bolt to fully engage the nut with several threads showing. Do not tighten these bolts enough to force the spigot further into the bell of the joint.

4. Remove the side bolts from the serrated restraint ring. Use the tie bolts to determine the proper location of the restraint ring on the spigot. Allow enough room on the tie bolt to fully engage the nuts.