EBA 430 E, 430 EP Operating Instructions Manual

EBA 430 E
EBA 430 EP

Operating Instructions

Printed in Germany • EBA 04/2002 • DPrinted in Germany • EBA 04/2002 • D

EBA 430 E • EBA 430 EP

-3-

Read through the operating instructions
carefully

Table of contents

Pages

Safety precautions 4 – 11
Installation 12 – 13
Operation 14 – 25
Blade replacement 26 – 34
Maintenance and cleaning 35 – 36
Possible malfunctions 37 – 42
Accessories 43
Manufacturer´s Declaration 45

-5--4-

The machine must not be located outside!

The machine must be installed on a sturdy, dry

and level floor!

Do not use in the vicinity of inflammable

liquids or gases!

-7--6-

This machine is only constructed for "one-man
operation"!

Disconnect from the mains before starting any
service work or before removing the panels!

Replacement of blade and cutting stick may
only be performed when the main switch is
switched off!

B

A

B

C

A

≤15mm
≤0.59inch

-9--8-

The dangerous cutting movement is
safeguarded by a movable guard (A) and a
safety two-handed control system! (B)

Before working with the machine and after
every blade replacement the automatic cut-off
function of safety guard (A),(correct if distance
between cover and table is < 15 mm) main
switch (B) and control panel (C) must be
checked.

-11--10-

When not in use for a longer period switch off.
(Main switch to "0").

-13-

C

A

B

Only on EBA 430 E

Screw on the backgauge crank (A) and
operating handle (B) (found together with
tools in the tool set).

Plug into socket.

-15-

B

A

C

D

Position the main switch to "I" (A). Insert the
key for the control system and move it to the
right (B). Open the safety guard (C). The
machine is now ready for use.

Only EBA 430 EP

Press

S button (D).

(Reference point is driven to).

B

C

A

EBA 430 E

EBA 430 EP

-17--16-

EBA 430 E

Measurement is indicated on the back side-lay
(A). The fine adjustment is achieved by using
the calibration ring (B). The scale is divided in
mm (One complete turn corresponds 10 mm =
1 cm).

EBA 430 EP

Measurement is shown in the display of the
control device in inches or cm (C).

B

A

C

-19-

Position the paper on the back gauge (A) and
side-lay (B). To move paper stacks, please use
the stacking angle (C).
(Run backgauge to the front for turning the
paper stack).

Close the safety guard.

cm

inch

-21--20-

Operating elements

A

- Guard front

B

- Safety two-handed control system

C

- Overload switch
(Blade drive/Backgauge drive)

D

- Backgauge control

E

- Clamping

F

- Main switch

G

- Handwheel for backgauge setting

H

- Key switch

I

- Backgauge

J

- Side gauge left

K

- Display cutting size (cm or inch)

L

- Select program step down

M

- Select program step up

N

- Stop and delete input

O

- Start

P

- Eject function

Q

- Keypad

R

- Changeover cm/inch

S

- Clear program

T

- Select program

U

- Enter

V

- Program number

W

- Program step

X

- Specified size

-23--22-

• Move the pressing lever

E

to the left by a slight

swing.

• Release the cut.

Eject function

If the

z button is kept pressed the backgauge

I

moves to a measurement of 9 cm (Basic

adjustment) and when released the

z button

returns to the measurement last set.
If the

z button is released while the

backgauge moves to the front, the
backgauge stops and moves back to the
measurement which has been set last time.

Cutting activation

Warning!

• Run backgauge to the front for turning the

paper stack.

• Do not interrupt the upward movement of the

blade by performing switching procedures.

• Release blade only when LED "S" has gone

out.

• Close the front guard

A

.

• Blade must always be at the top and be

covered by the clamp. Do not touch the
blade - risk of injury! (see security
information on page 34).

-25-

Eject function

• Set the measurements ➞ push the z

button.

• g Store the dimension.

Backgauge moves in the program for
unloading paper to the front and then to the
measurement which has been set in the
panel.

Cancel a program

• p Press ➞ P appears in the display..

• 1 ... 9 Enter program number 1 ... 9.

• Press c twice.

Each program has to be cancelled separately.
Single program steps can only be overwritten.

Deleting the last program step

• Press 0 .

• Press g .

p + s Escape the program mode.

Working with programs

• Press

p ➞ P appears on the display

•

1 ... 9 Enter Program number 1 ... 9

With the button

r and h you are able to change

between several program steps.
With

S the backgauge moves to the indicated

dimension.
With

s the backgauge stops.

General

LED "S" blinks ➞ the basic position will appear.
LED "S" is off ➞ the actual dimension appears.
In the program mode the ejection of paper

z is

not possible. The ejection of the paper has to
be programmed.

After each cut pressing the button

S the

backgauge moves to the next dimension.

Escape the program mode

• Press p ➞ P appears on the display.

• Press s ➞ Escape the program mode.

Program buttons

h and

r programms

By means of buttons

h and r dimension of your

choice can be reached.
(Basic adjustment

h = 38,5 cm, r = 9 cm).

• p and simultaneously h resp. r ➞ ( h U resp.

r D appears on the display.

• Insert the desired dimension.

• g Store dimension.

Display in cm or inch

• Press i ➞ Display changes between cm

and inch. (See picture left).

Adjust the eject-dimension

The eject dimension is programmed to
29,50 cm. It may be changed as follows:

• Press p Press p + z ➞ e on Display.

• Insert the desired dimension.

• g Store dimension.

-27-

1.

2.

Lower the blade by pressing both cutting
buttons (1.). Keep one button pressed and
turn off the main switch (2.).

Turn the blade depth adjustment screw to the
left until it stops (Screwdriver found in tool set).

-29-

1.

2.

1.

3.

2.

Remove the 2 blade screws (1.). Then put the
blade changing tool (2.) into place and fasten it
to the blade.

The remaining screws should then be removed
(1.). Loosening the grips of the blade changing
tool lightly (2.) will now allow the blade to be
taken downwards out of the machine (3.).

-31-

4-5 mm

0.15-

0.20 inch

C

A

B

B

1.

2.

Place the blade to be exchanged with the
blade changing tool mounted (1.), into the
blade carrier and push it up to the top and
screw it into place with the grips (2.).

Screw the exchange blade to the blade
changing tool as follows: (A)

• make sure there is a space ot 4 - 5 mm

or 0.15 - 0.20 inches (B).

• blade must be covered (C).

2.

1.

-33-

2.

1.

3.

5.

A

4.

Turn main switch to position I. (1.) The blade
will return to the upper position and the blade
screws should be tightened firmly (2.).

Close the safety guard (1.) Lower the blade by
pressing both cutting buttons (2.). Keep one
button pressed and turn off the main switch (3.).
Open the safety guard (4.). With the special
wrench (B) the 3 eccentrics shall be screwed
so far down (5.)until the paper is cut along the
entire length of the blade (The blade must
remain parallel, not too deep into cutting stick).

-35--34-

A

D

B

E

F

C

Maintenance work may only be performed by
trained staff.

Disconnect the mains before starting any
service work or before removing the cover.

Oil the backgauge (A) control weekly i.e.
grease it. (Use non-resinous oil and grease).
Twice a year the remaining 14
grease parts (B) (see picture).
To do this switch please bring the main switch
to position "0" (E) and move the machine on its
left sidfe.

Danger! of tilting!

Remove cover (C) and lower panel (D) (tools
in tool set).

• Remove remaining paper

• Grease the machine

• Check the two joining bolts and
pushing bar for wear

• Mount the machine upright

-37-

B

A

Machine does not function

Machine is plugged in?

Main switch to position "I"? Control system
activated? (Turn key to the right)

B

C

A

-39--38-

Does not cut through the last sheet:

• Turn or turn around the cutting stick (A),
readjust the blade by means of the blade
adjusting knob (B)

Poor cutting quality or blade stays in the
paper stack.

• change the blade (C) (see page 26-34).

-41-

cm

inch

EBA 430 E
Cut cannot be made.

• If cover is open:

close it.

• If cover is closed:
open and re-close it. (Security check).

EBA 430 EP
Cut cannot be made.

• Measurement has not been driven to
correctly.

• LED "S"

X

does not turn off.

Push again the

S button.

Security check of the cover (see above)

• Measurement below 9 cm

Hold the

S button

O

until the measure is

achieved.

• Backgauge

I

does not move, the display

shows "

C "

Turn the pressing lever

E

to the right.

• Backgauge

I

does not move to position
(pressing lever has been turned to the right).
"

C " is in the display

➞ inform service people.

-43-

Recommended accessories:

• Blade Nr. 9000 120

• Cutting stick (6 pieces) Nr. 9000 220

• Paper knock-up block Nr. 9000 520

• Blade changing tool Nr. 9000 515

• Cabinet Nr. 42618001

• Stand Nr. 43051100

-45-

Wolfgang Priester

-General Manager-

MANUFACTURER’S DECLARATION

This machine is approved by independent
safety laboratories and is in compliance
with the EC-regulations 98/37, 73/23 and
89/336.

EBA is certified under the DIN EN ISO
9001 quality standards.

The exact technical specifications can be
found on the technical specifications
sticker on the machine. A wiring diagram
is found in the electric switch box.

Applied standards and technical
specifications: 230 Volt-Version:
EN 292; EN 294; EN 349; EN 27779;
EN 55014-1; EN 55014-2; EN 60204;
EN 61000-3-2;

EN 61000-3-3; prEN

1010-1; prEN 1010-3
Sound level information: The sound

level is 71 db (A) as defined by DIN
45635/Teil 27.